Quooker PRO3 User manual

Installation guide PRO3
Before installing read this guide rst

Introduction
The operation of the Quooker PRO3
The Quooker system consists of a small tank which is connected to the cold water supply under
the sink and to the Nordic single tap, the Fusion tap or the Flex tap. Both boiling water and
mixed water can be drawn o from the Fusion and Flex tap. Inside the tank the water is heated
electrically to approx. 110°C and is kept at this temperature. The Quooker PRO3 has a capacity of
3 litres. Before the water leaves the tank it is puried by the HiTAC® water lter (High Temperature
Activated Carbon).
The Nordic single tap, the Fusion tap and the Flex tap are tted with a childproof push-and-turn
handle (see 'Tips for use'), which is clearly recognisable by its industrial ribbing. The Nordic single
tap is height adjustable to guarantee safe use. Both the Fusion tap and the Flex tap are well
insulated. Despite all the safety features incorporated in the product, anyone using the Quooker
system must keep in mind the risks of using boiling water in general. Incorrect use can lead to
injury. Therefore always read the manual carefully before use.
Installation, maintenance and warranty
The Quooker can be installed in almost any location provided there is sucient space for the tank
as well as a 13 amp socket, water supply and waste pipe.
The Quooker tank must be tted in an upright position. If the tank is to be tted in a cabinet with
drawers, an optional bracket can be purchased to suspend the tank from the cabinet wall.
The HiTAC® lter inside the tank should be changed once every 3-5 years depending on your
water hardness. If you live in a hard water area, lime scale will collect at the bottom of the tank
and will need to be cleaned out by one of our engineers approximately once a year depending on
usage and the quality of the water in your area. Alternatively, you can install a suitable descaling
system. This system must not reduce the pH level of the water below 7 or remove all the minerals
from the water (reverse osmosis) as this can be harmful to the tank and would void the warranty.
Suitable descaling systems are also available directly from Quooker as an optional extra.
The warranty period is two years and covers parts and labour. It does not cover issues resulting
from insucient lime scale maintenance.

Users
The Quooker tap can be used by children above the age of eight and people with diminished
physical, sensory or intellectual abilities provided they are supervised or have been instructed
on the safe use of the device. Inform people who are unfamiliar with the Quooker system about
safe use and the possible dangers associated with the use of the boiling-water tap. Please note:
incorrect use may result in injury. Prevent children from using the tap as a toy and do not allow
children to clean or maintain the product unsupervised. Keep the plug out of reach of small
children.
The Quooker system is suitable for household use and commercial use such as in sta kitchens
at shops, oces, farms and other business premises and for use by visitors at hotels, motels,
bed & breakfasts and other residential accommodation.
Always follow the installation method described in the manual. Avoid spilling water on the plug. If
defective, the power plug may only be replaced by a qualied technician. Make sure you let the
tank cool o adequately before disconnecting it. The fastest way to do this is as follows: turn
o the Quooker, but leave the plug in the socket. Then open the boiling-water tap and turn it o
once the water runs cold. You can nd a more detailed explanation for disconnecting the tank in
chapter F.
The installation manual can also be found on our website quooker.hk

Declaration of conformity
Quooker Nederland b.v., Staalstraat 13, 2984 AJ Ridderkerk (The Netherlands) herewith declares,
on our own responsibility, that the product Quooker PRO3 is in accordance with the conditions
of the following directives:
2014/35/EU Low Voltage Directive (LVD)
2011/65/EU Restriction of Hazardous Substances (RoHS) Directive
2014/30/EU Electromagnetic Compatibility Directive (EMCD)
2009/125/EC Ecodesign energy-related products Directive
2014/68/EU Pressure Equipment Directive
And are in conformity with the following standards:
General product safety household and similar electrical appliances
EN 60335-1:2012 + AC:2014 + A11:2014
EN 60335-2-15:2002 + AC:2005 + A1:2005 + AC:2006 + A2:2008 + A11:2012 + A11:2012/AC:2013 +
EN 60335-2-15:2016
EN 60335-2-21:2003 + A1:2005 + AC:2007 + A2:2008 + AC:2010
Public exposure to electromagnetic elds (EMF)
EN 62233:2008 + AC:2008
Electromagnetic compatibility (EMC)
EN 55014-1:2017 + EN 55014-1:2006 + A1:2009 + A2:2011
EN 55014-2:2015 + EN 55014-2:1997 + AC:1997 + A1:2001 + A2:2008
EN 61000-3-2:2014
EN 61000-3-3:2013
Restriction of hazardous substances
EN 50581:2012
The Netherlands, Ridderkerk, 1st of August 2020
Niels Peteri, Director

Technical specications
Tank PRO3
Voltage 230 V
Wattage 1600 W
Capacity 3 litres
Heating-up time* 10 minutes
Standby power consumption 10 W
Tank height 46 cm
Required working height 52 cm
Tank diameter 15 cm
Min. mains pressure 200 kPa (2 bar)
Max. mains pressure 600 kPa (6 bar)
Max. working pressure 800 kPa (8 bar)
Mounting bracket optional yes
Safety features - maximum temperature fuse
- pressure relief valve 800 kPa (8 bar)
Water shut-o valve electric
HiTAC® water lter High Temperature Activated Carbon
*These are average values.
Tap Nordic Fusion, Flex
single tap and mixer tap
Tap hole size 32 mm 35 mm
Recomm. temp. mixing water - 60°C
Tap base ring available yes yes

1
Contents of the pack
1. - Nordic single tap, packing ring, centring ring, steel ring, brass sink nut and two screws
- or Fusion tap, packing ring, brass xing plate, xing nut, white tap support (for thin work tops)
and two inlet hose screens
- or Flex tap, hoses, bre washer(s), steel washer, screw ring with two screws, coupling with
boiling water hose, white tap support, two inlet hose screens and quick-release tool.
Fusion Flex
Nordic single tap

1
4
2
5
2. PRO3 tank
3. Quooker inlet valve with packing ring
4. Angle stopcock with lter and packing ring
5. Inlet couplings and packing rings

Warm Cold
A
C
D
B1
Overview of Nordic single tap installation
It is recommended that you install the Quooker in the following order:
A. Drilling hole
B1. Fitting Nordic single tap
C. Connecting water
D. Connecting waste
E. Connecting tank
Note: Bear in mind that the tank, inlet valve and socket must remain easily accessible for servicing.
For an overview of the Fusion tap installation, please refer to the next page and for the Flex tap to
the page after that.

Overview of Fusion tap installation
It is recommended that you install the Quooker in the following order:
A. Drilling hole
B2.Fitting Fusion tap
C. Connecting water
D. Connecting waste
E. Connecting tank
Note: Bear in mind that the tank, inlet valve and socket must remain easily accessible for servicing.
For an overview of the Flex tap installation, please refer to the next page.
Warm Cold
A
C
B2
D

Overview of Flex tap installation
It is recommended that you install the Quooker in the following order:
A. Drilling hole
B3.Fitting Flex tap
C. Connecting water
D. Connecting waste
E. Connecting tank
Note: Bear in mind that the tank, inlet valve and socket must remain easily accessible for servicing.
Warm Cold
A
C
D
B3

1
3
2
A
1. Select position Nordic single tap
Select a suitable position for the Nordic
single tap based on the type of sink and
position of the mixer tap.
2. Drilling hole for Nordic single tap
Using the correct drill bit, drill a hole of
32 mm through the work top for the Nordic
single tap. Note: For the Nordic mixer tap
please refer to the separate guide. In the
case of a hole of 35 mm or larger, use the
centring ring provided.
3. Drilling hole for Fusion or Flex tap
Select a suitable position for the tap.
Using the correct drill bit, drill a hole of
35 mm through the work top. In this, take
account of the range of the tap’s spout
from the centre of the tap hole.
Drilling hole
• Note: The tap hole for the Nordic single tap should be 32 mm in diameter.
The Fusion and Flex tap hole should be 35 mm in diameter.
• The Nordic single tap should ideally be positioned at the corner of the sink to enable use
above the sink or the work top.
• Note: It must be possible to move the spout of the Nordic single tap freely up and down.
When the spout is in its lowest position it projects ca. 25 cm below the work top. Bear this in
mind when tting the inlet combination, sockets and the like.
• Note: The Flex tap coupling must be able to move freely. When the hose is not withdrawn it
hangs approximately 40 cm below the work surface top. Make allowances for this when tting
the inlet combination, power sockets and so forth.
Dimensions in mm
Max. thickness 60
Ø52
Hole
Ø35
220
±70
Dimensions in mm
Max. thickness 50
Ø50
Hole
Ø32
±70
160
Dimensions in mm
Max. thickness 50
Ø50
Hole Ø35
220
±70
Q
M
QM
Nordic single tap
Mixer tap

1
3
21. Tap through work top
Push the tap through the hole in the work
top. Note: When tting the tap in a 32 mm
hole, the black plastic ring needs to be
removed from the tap rst.
2. Securing the tap
Set the tap to the desired position and
secure it with the metal ring and screw ring
supplied.
3. Securing tap screws
Tighten the screws in the screw ring.
Fitting Nordic single tap
• The total length of the hose between the boiling-water tap and tank is only 70 cm. The tank
must therefore be tted close to the tap. Extension hoses are available in dierent lengths but
are not normally required.
• The small bre washers supplied with the tap rings are not required yet at this point. One will
be used for connecting the tap and tank hose (see section E), the second one is a spare.
B1

1
3
2
4
1. Mount the hoses
Mount the hot water and cold water hoses
on the tap.
2. Tap through work top
Push the tap through the hole in the
work top.
3. Securing tap
Position the brass xing plate around the
hoses. Screw the xing nut onto the tap
thread. Adjust the position of the tap to
ensure that the Quooker logo is facing
the user. When the handle is in the cold
position, it will be parallel to the edge of
the work top. Tighten the xing nut with a
pipe wrench, socket wrench or spanner.
4. Fitting to thin work top
When tting to a thin work top, use the
white tap support underneath the brass
xing plate.
Fitting Fusion tap
B2

1
3
2
4
1. Fit hoses
Fit the hot, cold and mixer water hose to
the tap.
2. Tap through work top
Push the tap through the hole in the work
top.
3. Tighten the brass plate
Put the tap in the required position and
fully tighten the brass plate.
4. Securing tap screws
Tighten the screws in the screw ring.
Fitting Flex tap
• When installing the reservoir it is necessary to take into account that the Flex tap coupling
must be able to move up and down freely.
B3

655. Attach the coupling
Click the pull-out hose into the coupling’s
quick-release tting while ensuring that
the hose pillar is fully inserted.
6. Fit the mixer water hose
Click the mixer water hose into the
coupling’s quick-release tting while
ensuring that the hose pillar is fully
inserted.
If necessary
Detach coupling. Use the quick-release
tool to detach the mixer water hoses from
the coupling. Press the quick-release tool
at against the coupling to hold it still.
This enables the hose to be extracted.

1
3
21. Shut o water
Before installation, shut o the angle
stopcock or water supply to the main
water tap. If necessary, t supplied angle
stopcock.
2. Connect inlet valve
Connect the inlet valve to the angle
stopcock with the bre washer.
3. Connect hot and cold water hose
Connect the hot water hose with the water
lter to the angle stopcock. Connect the
cold water hose with the hose lter to the
inlet valve.
If necessary
If only a G½” connection is present,
use one of the G½” couplings with the
supplied packing rings.
Connecting water
• The Quooker operates under mains water pressure and must always be tted to the water pipe
with the supplied inlet valve.
• The Nordic single tap, the Fusion tap or the Flex tap must be installed according to the locally
applicable regulations.
C
Warm
C
old
Cold
Warm
Cold

2
4
1
3
1. Connecting tank and tap
Position the tank and connect to the inlet
valve using the washer provided. Using
size 10 and 14 socket spanners, connect
tap hose to tting at the top of the tank.
2. Electrical connection
Insert the LED cable into the relevant
opening. Connect the tank to an earthed
socket. Do not switch on until the tank is
lled with water.
3. Filling tank
Open tap and angle stopcock. Check for
leaks. Rinse Quooker for a few minutes,
until the water is clear. The initial black
colouring is activated carbon from the
lter and completely harmless.
4. Switching on
Switch the tank on. After the Quooker has
heated up, the entire content of boiling
water must be ushed out once before use.
Connecting tank to tap
• The Quooker tank is supplied with a UK 3 pin plug and requires a standard 13 amp
earthed socket.
• If the mains lead is damaged, it must be replaced by the manufacturer, their agent or a
qualified technician.
• The ‘Q’ on the lid is the on/off switch.
D
On/o ff
10
14

2
4
1
3
1. Switching o
Press the on/o switch at the top of the
tank to switch it o. Do not unplug the tank
from the socket yet.
2. Draining
Open the boiling-water handle of the tap
and leave the water running until it is cold.
Then close the tap again. Note: At rst, the
water is very hot.
3. Isolating
Close the main shut-o valve or the angle
stopcock for cold water. Check that the
Quooker is depressurized by opening the
Nordic single tap or the boiling-water
handle of the Fusion or Flex tap again. If
it is depressurized, no water should ow
out of it.
4. Disconnecting
Unplug the LED cable from the lid. Release
the hose connections and pull the plug
out of the socket. Remove the inlet
combination and reconnect the cold water
hose to the angle stopcock.
Disconnecting tank
• In case of service.
E
On/o ff

HK 30.398.15 V01
Quooker Hong Kong Ltd.
10/F, YF Life Tower
33 Lockhart Road
Wanchai
Hong Kong
[phone]
[e-mail]
www.quooker.hk