Qvis PX-SDH2010 User manual

Infrared Speed Dome
Manual V2.1

1. Precaution
1
Precaution
Environmental requirements
Electrical safety
Conform to country and local electrical safety standard when using or installing the product.
Using local special power adapter.
Transportation
The dome should be protected against extremes of pressure, vibration and humidity during
storage and transportation. It should be shipped in parts disassembled as the original packing did.
Damage caused by improper transportation is not within the warranty.
Installation with care
Do not install it in any other orientation. Do not squeezed structure parts, which may cause
mechanical damage. Down cover is a precise optical product. Do not touch it directly to avoid
scratches which can affect image quality.
Requirements to service personnel
All the service work should be done by qualified technicians.
Don't place the camera to be shoot by strong light objects
Don't place the camera to be shoot by strong light objects. Don't point the dome to the sun or
other bright objects when in use or not. It may affect image quality.
Operation environment temperature：-10℃ ～+60℃/-40~+6 0
Humidity：< 90%
Air pressure：86-106Kpa
℃(bulid i n h e ater)
1. Connect the power line, video cable and RS485
cable.
Picture 2.2.1-1
Red
Black
Power connector
Video connector
2. 2 Product schematic drawing
2
3 Performance and feature
3.
Iron and carbon alloy structure, high intensity, and good heat dissipation.
Precise stepping motor, rotate smoothly, react sensitivity and orientate accurately.
Rotate slowly at pan 1°/s, and the image doesn't jitter.
Built-in pan/tilt
Exquisite mechanical drive, support pan 360°continuously and tilt 0-90°, and may rotate180°
with auto flip.
●
●
●
●
This product is high-technology surveillance product with high definition and color camera,
variable-speed pan/tilt and multifunction decoder. It can reduce the connection and installation
process between systematic parts at a max limit, and also can improve the stability and reliability
of the system. Meanwhile it is easy to install and repair, and it has the following advantages: beau-
tiful shape, rotate lightly and neatly, little noise, simple operation and so on.
1. Built-in digital camera
2. Integrated and multi-protocol decoder
●
●
●
●
●
●
Figure design, all the data are stored in the inner of camera pan/tilt,when power off, the storage
data can't be lose.
Built-in decoder, integrated multi-protocol，including PELCO-D, PELCO-P, FACTORY, etc.
128 presets can be stored, preset 1-80 support auto tour, and each tour can store up to 32 presets.
4 pattern, 4 scan, 4tour
Built-in direction indicator and temperature indicator
Rs485 bus controlling in series, and dome ID 1-255 optional
4. OS
All the menu option are displayed in English.
Video OSD menu. It is direct and simple to revise the dome information and parameter by
keyboard and menu display.
May set park action, and set power up action or carry out appointed action.
D menu
●
●
●
●
●
When the temperature exceeds the upper limit, the screen will display alarm information.
According to the real-time temperature, the fan will measure if it starts or not, and prolong the
life of fan.
5. Internal temperature test
● High sensitivity, high resolution, and integrated digital processing
● Auto-focus ● Auto-Iris
● Auto brightness control ● Auto white balance
● IR cut filter ● Auto back light compensation
● Auto slow shutter
Attention:
Different series product may have
different adaptor,Please refer to
the sticker on the wire or on the box
with your products, otherwise it may
damage the product.

4. Function instruction
Auto flip
If user holds the joystick in the down position, the camera rotates pan 180 degrees, he
camera rotates tilts up to 90 degrees, you may directly watch the rear view
ocesses in portrait 180 degrees . In the menu, you may set the system parameter setting AUTO
FLIP as ON, thus you may run this function.
●
then t
to realize surveillance
all pr
Function instruction
This passage mainly describes the main function and general principle of mini speed dome,
and does not refer to the operation methods.
4. 1 Auto-run motion
IDLE RUM
By the menu IDLE RUN and idle action , user may set auto-call preset or run tour, pattern,
and scan, etc after pointing a few minutes if the dome doesn't run any motions.
●
“ ” “ ”
● Focus/speed proportion pan
When manually adjusting, for far focus situation, the dome responds at a high-speed so that
touching rocker slightly may make picture move rapidly, thus cause the picture to lose. To base
on humanized design, the dome automatically adjust pan and tilt rotation according to zoom near
and far, which make it is convenient to operate manually to make tracks for the object. In the menu,
you may change system parameter setting proportion pan as ON, thus you may run this function.
● Magnification control
The user can control Wide/Tele to adjust zoom far and near of the image by keyboard controller to
obtain panoramic image or close view that you need. The speed dome support digital zoom and optical
zoom.
●Focus control
System defaults Auto focus. When the lens changes, camera will auto-adjust focus according to the
centre of the image to get legible image; user also can manually focus to get desire image by operating
keyboard FAR/NEAR . When operating keyboard joystick, camera resumes to auto focus.
The camera cannot auto focus in the following status:
●Target is not the centre of the image
●Observation the target near and far at the same time, can not be clear at the same time.
●Target is a strong light object, such as spotlight etc.
●Target moves too fast
●Target is subfusc, such as wall
●Target is too dark or vague
●Target image is too small
" "
" "
4. 2 Camera control
● Power up run
By the menu power up run , after the dome powers up or restarts, user may set auto- resume
motions before power up and auto- call preset or run tour, pattern, and scan etc .
“ ”
3
ØIris control
System defaults Auto Iris. Camera can rapidly adjust size of Iris, through the automatically induct the
changing of environment ray, and thus make the brightness of deferent image stable.
User may adjust iris by controlling keyboard to get required brightness that you
need. User also can resume auto Iris by joystick operation. When controlling the Iris manually, the dome
locks current position you manually controlled; when operating joystick, the dome resume auto Iris.
ØAuto back light compensation
Camera sub-area can carry out auto back light compensation. Under a strong light background, camera
will auto compensate light for the darker object and adjust daylight to the bright background. In order to
avoid making the image lack fidelity by the back line is too bright, and the object is unable to recognize
because of darkness, thus gain legible image.
ØAuto white balance
Camera can automatically adjust white balance in accordance with the alteration of background light-
ness to reach a true colour.
"OPEN/CLOSE"
4. 3 Monitor function
Tour
Tour is the built-in function in the speed dome. It can appoint setting in advance, and make pre-
sets arranged in needful order in tour dwell. By inserting presets in tour dwell, to make the camera
tour between these presets. Tour order can be programmed, each time you run tour, you can set park
time. A tour can store 32 preset.
Scan
User can easily preset right limit and left limit by controlling menu and menu, in order to make
the camera scanned between right limit and left limit at a setting speed.
Pattern
Pattern is built-in function in the speed dome; the dome can record the tracks that are no less than
180s, when running pattern, the dome moves repeatedly according to the recorded tracks. Each dome
can set up to 4 pattern.
Lens position display
The position that the speed dome has finished to self-testing as 0 point of pan rotation and tilt
rotation. The pan range is 0-360°, and tilt range is 0-90°. According to the displayed information,
to set the position of camera lens, and the position can display on the screen.
Ø Set and call preset
Preset function is that dome stores current pan/tilt angle, zoom and other position parameters
into the memory. When necessary dome recalls these parameters and adjust camera to that position.
User can store and recall presets easily and promptly by using keyboard controlling. The dome can
store up to 128 presets.
Ø
Ø
Ø
Ø
4. 4 Constant temperature Function
Inner temperature sensor surveille temperature inside of the dome. When the dome work in
the high temperature, the dome will automatically to start-up the fan to reduce the heat, to make
sure the dome work in the reliable temperature environment, increase its stability and prolong the
life time of the dome.
4
Function Instruction

The dome conducts self-testing after current-carring,and it rotates slowly until displaying pan origin
that is default setting, then moving to tilt origin, when self-testing is finished, there is relevant system
information displaying on the screen, as follows:
5. 1. 2 Call the main menu
The system enters into the main menu by 95preset or twice transfer 9 preset in 3 seconds . All the menu
setting must enter into the main menu at first.
Ø Keyboard operation：
【OPEN】 ， it means to enter the next menu or enter into setting, or save after
finish to set.
【CLOSE】 ，it means to close to cancel, or exit to the former menu.
【 】
.
【 】
Press 【TELE】and 【WIDE】at the same time, it means 3D joystick rotates joystick cap.
Ø Menu operation：
“BACK”: Back to the former menu.
“EXIT”：Exit to menu
“ON”：Open some setting
“OFF”：Close some setting
The information will not disappear until you stop to operate the system. If you set“power up action”,
the dome will automatically activate motions after self-testing. How to operate the function? We will explain
detail introduction in following passages.
when choosing menu
when choosing menu
Joystick to up: When choosing menu, it means to choose the former one; when choosing picture, it
means camera tilt up.
Joystick to down: when choosing menu, it means to choose the next one; when choosing picture, it
means camera tilt down.
Joystick to left: when choosing menu, it is equal with Close , when choosing picture, it means
camera tilt left
Joystick to right: when choosing menu, it is equal with Open , when choosing picture, it means
camera tilt right.
5. 1 Basic operation
5. System setting
5. 1. 1 Power up and self-testing
5. 1. 3 Menu and keyboard operation
DOME S/N:
VERSION:
DOME S/N:
VERSION:
PROTOCOL: FACTOTYPROTOCOL: FACTOTY
DOME ID：001 DOME ID：001
BAUD RATE: 4800bpsBAUD RATE: 4800bps
MODEL:MODEL:
So ft w ar e ver si on
Protocol
Do me I D
Communication parameter
Se ri a l nu mbe r of t he do me
Mo de l
5
System setting
6
System setting
5. 3 Dome initial information
1. Call
2. to
SYSTEM , press to enter submenu.
3. to
DOME INFO , press to display initial information
as the left picture shows.
Initial information includes S/N of the dome, soft edition,
protocol, dome ID, communication parameter. SYSTEM may
change the numerical value of initial information.
95 preset or transfer 9 preset twice in three seconds to enter
the main menu.
【 】 【OPEN】
【 】 【OPEN】
Operate the joystick up and down and move the cursor
Operate the joystick up and down and move the cursor
DOME INFO
DOME S/N: 0001
VERSION : V1.00
MODEL :DOME
PROTOCOL:PELCO
DOME ID：001
BAUD RATE：4800bps
BACK
EXIT
SYSTEM SETTING
DOME INFO
ID SETTING
AUTO RUN
DEFAULTS
BACK
EXIT
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT

1. Call 95 preset or call 9 preset twice within 3 seconds, to enter into
main menu.
2. Operate the joystick up and down and move the cursor to SYS-
TEM 】, press OPEN to enter submenu.
3. Operate the joystick up and down and move the cursor to【
ID SETTING】, press【OPEN】to call dome parameter setting menu.
【S/N】: Series number of the dome
【CONF】: Confirm S/N and input the same number with S/N
【ID】: Set dome address (ID range: 001-255)
【
【 】
1.If [S/N] and [CONF] are different, the above operation
can't be implemented.
2.The dome address should be set as 255 by setting SW1
as ON at first, there will be display this item [DOME ID]
3.After setting dome address, the dome need to restart, then
the dome address will be effective.
5. 4 ID Setting
NOTICE
S / N : 0025
CONF : 0000
ID : 001
BAUDRATE : 9600
BACK
EXIT
ID SETTING
7
The shortcut of Dome ID setting: call 101-116 preset twice within
3 seconds, to set dome ID as 1 to 16. For example, call 103 preset
twice within 3 seconds, then dome ID be setted as 3.
SYSTEM
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
SYSTEM SETTING
DOME INFO
ID SETTING
AUTO RUN
DEFAULTS
BACK
EXIT
1
2. 【
】 【 】
Systematic motion controlling may control a series of canonical
movement of the dome, and plays an important role in controlling
the image of the dome.
. The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds.
Operate the joystick up and down and move the cursor to SYST-
EM , press OPEN to enter submenu.
5. 5 AUTO RUN
AUTO RUN
AUTO FLIP ON
PROPORTION ON
POWER UP RUN NONE
IDLE RUN
BACK
EXIT
SYSTEM
Operate the joystick up and down and move the cursor to
Operate
the joystick " ", and
" "
【PANT-
ILT SETTING】, press【OPEN】to enter【AUTO FLIP】.
up and down to choose ON to open auto flip choose
OFF to close auto flip . Press【OPEN】to save.
When manually adjusting, for far focus situation, the dome
responds at a high-speed so that touching rocker slightly may
make picture move rapidly, thus cause the picture to lose. To
base on humanized design, the dome automatically adjust pan
and tilt rotation according to zoom near and far, which make it
is convenient to operate manually run after object.
OPERATION KNACKS
Operate joystick and move the cursor to【PROPORTION】,
press【OPEN】to enter "proportion" setting, operate joystick up
and down to choose, if choosing【ON】, it means to open proportion
pan. If choosing【OFF】, it means to close proportion pan , press
【OPEN】to save.
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
SYSTEM
DOME INFO
ID SETTING
AUTO RUN
DEFAULTS
BACK
EXIT
5. 5.1 AUTO FLIP
8
5. 5.2 PROPORTION

5. 5. 3 Power up run
The dome startup to run actions after self-testing, if nobody
intervenes with it , the dome will repeatedly run this action continu-
ously , if default sets as 【NONE】.
Operate joystick, move the cursor to 【POWER UP ACTION】:
press【OPEN】 to jump to the following choice, tilt up/down joystick
to choose power up action , press 【OPEN】 to save.
●【NONE】: none action
●【AUTO】: the dome resumes the primary action and
direction before power up.
●【PRESET】: use preset
●【SCAN】: run scan
●【PAT】: run pattern
●【TOUR】: run tour
" "
9
SYSTEM
AUTO RUN
AUTO FLIP ON
PROPORTION ON
POWER UP RUN NONE
IDLE RUN
BACK
EXIT
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
SYSTEM
DOME INFO
ID SETTING
AUTO RUN
DEFAULTS
BACK
EXIT
This setting allows the dome to run an appointed action after
it enters vacancy for a few time (1-240minutes). If default sets as 0,
it means not to run this action.
1. Operate the joystick up and down and move the cursor to
, press OPEN to tilt up/down joystick to set
idle time, the range is 0-240 (minute), press OPEN to save.
PARK ACTION is running action at park time, when PARK
TIME sets as 0, this item can't be set.
2. Operate the joystick up and down and move the cursor to
ACTION , press OPEN there will be a sign in the front
of , the cursor jump to right, after tilting up/down
joystick to choose "idle action", there are options for choosing as
follows, press OPEN to save.
【IDLE
RUN 】【 】
【 】
【】【
】
【IDLE
】【 】 “ ”
【IDLE ACTION】
【 】
5. 5. 4 IDLE RUN
●【NONE】: (default)
●【PAT】:
●【TOUR】:
●【SCAN】:
●【PRESET】:
no action
run pattern
run tour
run scan
use preset
IDLE RUN
IDLE TIME : 000
IDLE ACTION : NONE
BACK
EXIT
5. 6 Defaults
1
2. 【
】 【 】
3. 【DEFA-
ULTS】 【 】
● 【CLEAR ALL PRESETS】
● 【CLEAR ALL PATTERNS】
● 【CLEAR ALL TOURS】
● 【FACTORY DEFAULTS】:
● 【RESTART】 ：restart the dome
. The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds.
Operate the joystick up and down and move the cursor to SYST-
EM , press OPEN to enter submenu.
Operate the joystick up and down and move the cursor to
, press OPEN to enter submenu, as left picture shows
resume the factory default.
Run this function, the camera parameter and system parameter will
resume before production, clear all windows and alarm setting.
Please be cautious to use this function.
DEFAULTS
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
FACTORY DEFAULTS
RESTART
BACK
EXIT
NOTICE
Once clear all commands in the controlling menu,
they don't resume, so please be careful of using.
1 0
SYSTEM
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
SYSTEM
DOME INFO
ID SETTING
AUTO RUN
DEFAULTS
BACK
EXIT

1 1
6. 1 Preset
6. Function setting
1
Define
【
】 【 】
【 】
【 】
【 】
【 】
【 】
5【 】
【 】
. The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds. Click each command to
enter "preset menu" according to the order of the left picture. As
follows:
preset and call preset function can be set by keyboard
operation, input preset number at first, then click the key "save /call
preset" to carry out.
2. Define current preset number: move the cursor to PRESET NUM
-BER , press OPEN to choose preset number, the range is 01-
128 as the left picture shows, here chooses number 5 as current preset,
the following operations aim at the current preset.
3. Define current preset: move the cursor to SET PRESET ,press
OPEN , by operating joystick to adjust magnification, to choose
good objective image, press OPEN to save. If the image is very
near, the image is belong in digital zoom; when setting preset, the
image will jump to maximal optical zoom.
4.Display current preset: move the cursor to SHOW PRESET ,
press OPEN , the screen will display the current preset.
.Clear current preset: move the cursor to CLEAR PRESET ,
press OPEN , the current preset is cleared.
Preset function is that dome stores current pan/tilt angle, zoom
and other position parameters into the memory. When necessary dome
recalls these parameters and adjust camera to that position.
OPERATION KNACKS
● 【PRESET NUMBER】
● 【SET PRESET】
● 【SHOW PRESET】
● 【CLEAR CURRENT PRESET】
PRESET NUMBER 001
SET PRESET
SHOW PRESET
CLEAR PRESET
BACK
EXIT
PRESETS
FUNCTION
PRESETS
SCAN
PATTERNS
TOUR
BACK
EXIT
1 2
Function setting
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
6. 2 Scan
1.
● 【SCAN NUMBER】
● 【SCAN SPEED】
● 【SET LEFT LIMIT】
● 【SET RIGHT LIMIT】
● 【RUN SCAN】
● 【CLEAR SCAN】
2. Define current scan number: operate joystick ,move the cursor to
【scan number】, press【open】,tilt up/downjoystick to choose scan
number, press【open】to save. The following operations aim at the
current scan number.
3. 【 】
【 】 【 】
【 】
【 】 【 】
【 】 【 】
Scan is that pre-set two points , then the camera repeatedly scan
between the two points at a stable speed, the same magnification and
pan. Each dome has four scan.
The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds. Click menu to enter "scan"
menu, as the left picture shows.
Scan speed setting: operate joystick to SCAN SPEED , press
OPEN , tilt up/down joystick to adjust scan speed, press OPEN
to save.
4. Left limit setting: operate joystick to SET LEFT LIMIT , press
OPEN , operate joystick to choose objective image, press OPEN
to save. Right limit setting is the same as left limit setting..
5. Run scan: operate joystick to RUN SCAN , press OPEN
to exit the menu, and it starts to run scan.
FUNCTION
PRESETS
SCAN
PATTERNS
TOUR
BACK
EXIT
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
SCAN
SCAN NUMBER 1
SCAN SPEED 20
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR SCAN
RUN SCAN
BACK
EXIT
Function setting

1 3
Function setting
6. 3 Pattern
2【
】 【 】
3【
】 【 】
4【 】
【 】
5【RECORD
】 【 】
【 】
6【 】
【 】
Pattern is built-in function in camera; the speed dome can record
tracks that are no less than 180s. (A series of pan/tilt controlling and
lens controlling command). Each dome may set up to 4 patterns.
1. The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds.
. Operate the joystick up and down and move the cursor to FUN-
CTION SETTING , press OPEN to enter submenu.
. Operate the joystick up and down and move the cursor to PAT-
TERN , press OPEN to enter menu "Pattern".
. Choose pattern number: move the cursor to PATTERN NUMBER ,
press OPEN , the pattern you choose as current one, the following
operations aim at the current pattern.
. Define current pattern tour: move the cursor to PAT-
TERN , press OPEN to set pattern track, move the image
random, and draw the focus. Each dome has a tour that is no less than
180s, a series of park time, magnification, focus will be recorded,
press OPEN to save.
. Run pattern: operate joystick to RUN PATTERN , press
OPEN to run, the dome will continuously and repeatedly record
the specific track.
PATTERNS
PATTERN NUMBER 1
RECORD PATTERN
RUN PATTERN
CLEAR PATTERN
BACK
EXIT
● 【PATTERN NUMBER】
● 【 PATTERN】
● 【RUN PATTERN】
● 【CLEAR PATTERN】
RECORD
FUNCTION
PRESETS
SCAN
PATTERNS
TOUR
BACK
EXIT
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
6. 4 Tour
TOUR
PO-S-TM PO-S-TM
00-00-00 00-00-00
00-00-00 00-00-00
00-00-00 00-00-00
00-00-00 00-00-00
BACK
EXIT
Tour is the built-in function in the speed dome, it will arrange
the presets into the queue of auto-tour, and can set how long it will
park at preset. Operate auto-tour is a process of incessantly transfer
each preset. One tour can store 32 presets at most.
The system enters into the main menu by calling 95 preset or by
calling 9 preset twice within 3 seconds.
Operate the joystick up and down and move the cursor to
FUNCTION , press OPEN enter submenu.
Operate the joystick up and down and move the cursor to
TOUR , press OPEN to enter menu "tour".
5 Run tour: Operate joystick, move the cursor to RUN TOUR ,
press OPEN to exit the menu, it starts to run tour.
1.
2.
【 】 【 】
3.
【 】 【 】
4. Set tour: move the cursor to【EDIT TOUR】, press【OPEN】
to set tour interface,【PO-S-TM】set preset, speed and time, press
【OPEN】, the first dwell is activated , tilt up/down joystick to
choose preset number, the preset numerical value should be within
1-80 preset, a tour can set up to 24 presets. Press【OPEN】,the
cursor jump to the next dwell, tilt up/down joystick to choose
current arrival preset speed , total 8 level of speed , increasingly
from level1 to level 8. Press【OPEN】, the cursor jumps to the
next dwell, tilt up/down joystick to set current preset maintaining
time, 60 seconds maximum. If set the presets of the second line ,
move the cursor to the second line, press【OPEN】to continue
edit. Press【OPEN】to save after setting, press【CLOSE】 to exit.
. 【 】
【 】
● 【TOUR NUMBER】
● 【 TOUR】
● 【RUN TOUR】
● 【CLEAR TOUR】
EDIT
1 4
TOUR
TOUR NUMBER 1
EDIT TOUR
RUN TOUR
CLEAR TOUR
BACK
EXIT
FUNCTION
PRESETS
SCAN
PATTERNS
TOUR
BACK
EXIT
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
Function setting

1 5
No action, no
video after
power up
Possible causesTrouble Solution
8 Trouble shooting
Power line connected wrong Correct
Engineering line is malfunction
Self-testing and
image are normal
but the dome is
uncontrollable
The dome DIP switch setting
is incorrect
Refer to switch setting,reset the switch
Rs485 may carve out a way Check Rs485connection, confirm
the connection is correct and
good in contact
Rs485 is in malfunction Pls consult appendix“Rs485
Bus acknowledge”
Video image
is not steady.
Video line is bad connection
Eliminate
Power consumption is not enough
Video image is
not steady and the
motor is faulted
Power consumption is not enough
Replace the power
Dome controlling
is not smooth.
Controlling line connected
wrong, or Rs485 loads too
much or the distance of
communication is too far
1.Connect 120Ω resistance in the dome pan/tilt
that is far from the controller
2.Increase distributor
Power supply is damage or
power consumption is not
enough
Replace
Replace right power adapter, it is better to put
the switch and power adapter near the dome
To obtain constant clear videos, user should
clean the down cover periodically.
● Be caution when cleaning, hold the down cover
ring only to avoid direct touch to the acrylic down
cover. The acid sweat mark of fingerprint will corrode
the coating of down cover and scratch on down cover
will cause vague image.
● Use soft dry cloth or the substitute to clean the inner
and outer surfaces
● For hand contamination, use neutral detergent. Any
cleanser for high grade furniture is applicable.
8.1 The cleaning of clear down cover
Check and repair
1 6
Appendix
Infrared setting
7.Infrared led setting
7.1 IR SENSITIVITY:
infrared automatic open sensitivity settings, range 0~100, the user can
according to the environmental illumination status modulates infrared
automatic open
7.2 MANUAL DELAY:
infrared light manual opening, closing time, if time is 0,Do not
automatically close infrared lamp
7.3 IR ON/OFF:
IR control mode, can be divided into a, AUTO, MANUAL, TIME
three models,In TIME model, according to the user set time to switch
IR; in MANUAL mode,Call the 62 preset command to open the
infrared light, open the63 preset closed lamp
7.4 IR LUMINANCE:
infrared brightness control method in infrared light,open effect after,
Divided into: AUTO, GROUP, MANUAL, three states AUTO mode,
infrared automatic brightness matching lens distance, according to the
cameralens changes,Infrared high beam and dipped beam headlights
will automatically adjust the brightness, reach the intensity of
illumination and brightness automatic matching,And can improve the
infrared lamp life.
GROUP mode：packet mode,in a packet mode,infrared high beam and
dipped beam headlights will match According to the lens distance packet
opened at the same time.
MANUAL mode: the manual control mode, infrared brightness from
the lens parameters influence,The user can set the high beam and dipped
beam brightness, range 0~100
MAIN MENU
SYSTEM
CAMERA
FUNCTION
INFRARED LED
EXIT
INFRARED LED
MANUAL DELAY
IR ON/OFF
LUMINANCE
BACK
EXIT
SENSITIVITY
IR ON/OFF
ON TIME N/A
OFF TIME N/A
BACK
EXIT
IR ON/OFF AUTO
LUMINANCE
TELE LED N/A
WIDE LED N/A
BACK
EXIT
LUMINANCE AUTO

Connection and termination resistor
The Rs485Bus standards require a daisy-chain
connection between the equipment. There must be
termination resistors with 120Ω(as the picture 9.4
-1). Please refer to picture 9.4-2 for simple
connection. D should not exceed 7m.
8.2 RS485Bus basic knowledge
120Ω
1# 2# 3# 4# 32#
Picture 9-4.1
120Ω
2400bps
4800bps
9600bps
1800m
1200m
800m
Baud rate Max distance
19200bps 600m
As specified by Rs485 standard, Rs485 Bus
is of half-duplexed data transmission cables with
characteristic impedance as 120Ω. The maximum
load capacity is 32unit loads(including main
controller and controller equipment)
Characteristics of Rs485 Bus
Transmission distances of Rs485 Bus
When user selects the 0.56mm(24AWG) twist
pair wires as data transmission cable, the max
theoretical transmitting distance are as follows:
If user selects thinner cables, or installs the
dome in an environment with strong electroma-
gnetic interference, or connects lots of equipment
to the Rs485Bus, the max transmitting distance
will be decreased. To increase the maximum
transmitting distance, do the contrary.
120Ω
1# 2# 3# 4# 32#
D
A+
B-
A+ B-
Picture 9.4-2
120Ω
Problems in practical connections
In some circumstances user adopts a star
configuration in practical connection. The
termination resistors must be connected to
the two equipment 1# and 15# in picture 9.4-3.
As the star configuration is not in conformity
with the requirements of RS485 standards,
problems such as signal reflections, lower
anti-interference performance arise when
the cables are long in the connection. The
reliability of control signals is decreased
with the phenomena that the dome does not
respond or just responds at intervals to the
controller, or does continuous operation
without stop.
1#
32#
15#
6#
Main controller
Picture 9.4-3
120
120
In such circumstances the factory reco-
mmends the usage of RS485 distributor.
The distributor can change the star config-
uration connection to the mode of connection
stipulated in the RS485 standards. The new
connection achieves reliable data transmi-
ssion (Refer to Picture 9.4-4).
RS 485 D i str i but o r
B-
1#
2#
3#
120Ω
120Ω
120Ω
A+ 120
120
120
Picture 9.4-4
1 7
Trouble Possible cause
Solution
Dome can
do self-
testing
but can
not be
controlled
The dome can
be controlled
but the opera-
tion is not
smooth
1. Chage the address and baud rate of contro-
ller or dome
2. Adjust the + and -connection of Rs485
3. Make sure the connections are fully seated
4. Change RS485 Bus wires
1. Secure the connection
2. Replace RS485 bus wires
3. Add termination resistors to the
system
4. Install RS485 distributor
RS485Bus troubles shooting
1. The address and baud rate setting
of dome are not in conformity with
those of controller.
2. The + and - connection of RS485
Bus is incorrect
3. Bad connection
4. There are circuit in the RS485
Bus.
1. The RS485Bus is not in good contact with
the connectors
2. One wire of RS485bus is broken
3. The dome is very far from controller
4. There are two many domes connected in the
system
1 8
Appendix Appendix
CALL+”N”+PRESET Show preset
SET+”N”+PRESET Save preset
CALL+”95”+PRESET Enter menu
CALL+”94”+PRESET Restart
CALL+”92”+PRESET Set scan1 Left limit
CALL+”93”+PRESET Set scan1 Right limit
CALL+”97”+PRESET Run scan1
CALL+”99”+PRESET
CALL+”62”+PRESET Open IR LED(manual state)
CALL+”63”+PRESET Close IR LED(manual state)
CALL+”98”+PRESET Run tour1
Run scan1
9.Shortcut key:

1 9
9. Maintenance
(1) Range of warranty
(2) Warranty terms
(3) Shipping
●
●
●
●
●
●
●
●
● For the damage and loss which was caused by the user's specifically application, factory won't
bear any risk and responsibility. The factory compensation made by breach of faith, negligence
or tortious won't exceed the amount of the products. The factory won't bear any responsibility
for the special, unexpected and continue damage caused by any other reasons.
● Our company has the final right of explanation for the above terms.
If the products are within the warranty time, the buyer should fill in the warranty card and send
back together with the products.
If the product needs repaired , you can return it to the manufacturer through the supplier or
directly. If you choose the later , please contact us in order to speed up the process. And our
company only undertake the one-way freight from manufacturer to customer after maintenance.
The product will be maintained free for one year.
The product will be obtained the free maintenance service if the same malfunction appears
again within three months.
Malfunction of products caused by force majeure (such as war, earthquake, lightning strike
and so on ), abuse, non- standard operation, change of construction, non-normal wear or accident
are non-free of warranty.
Please prevent from the damage which is caused by heavy pressure , the fierce vibration and
soaks in the process of transportation and storage, which does not belong to the free maintenance
scope.
Please adopt the way of fission package or original package to transport because the product
damage dose not belong to the free maintenance scope if you use the whole packing way , not the
original packing way.
The maintenance services will not be free when the pan/tilt module is disassembled or
serviced by the user voluntarily.
Our company implements the lifetime payable service if the product in malfunction has
surpassed the warranty period.
To the products with defect :if it's in the period of warranty, please fill in the form of warranty
information correctly, describe the trouble in details , and provide the trouble in details , and
provide original sales invoice or its copy.
Maintenance