Qzeri Ultra Wind Series OZF1 User manual

With Smart LCD & Remote Control
Model No: OZF1
The images in this manual are for illustration purposes only and may vary slightly from actual product.

Important Safety Instructions
Thank you for purchasing the Ozeri Ultra 42”Fan. This product
haspassed extensive quality assurance tests for residentialuse.
Every care has been taken to ensure that it reaches you in perfect
condition.
Warning: When using electric appliances, basicsafety precautions
personal injury, including (but not limited to) the following:
Read all these instructions before attempting to operate this
product andsave theseinstructions for future reference:
THIS FAN HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN
THE OTHER). TO REDUCE THE RISK OF ELECTRICAL SHOCK, THIS
PLUG IS INTENED TO FIT IN A POLARIZED OUTLET ONLY ONE
WAY. MATCH THE WIDE BLADE OF THE PLUG TO THE WIDE SLOT
OF THE OUTLET. FULLY INSERT. IF THE PLUG DOES NOT FITFULLY
IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOESNOT FIT,
CONTACT A QUALIFIED ELECTRICIAN. DONOT ATTEMPT TO
BYPASS THIS SAFETY FEATURE.
Use this fan only asdescribed inthis manual.
Checkthe voltage indicated on the rating plate. This fan is
designed for a 120V-60Hz electric supply. Make certain the
power source conforms to these electric requirements. Make
sure the room where this fan willbe usedhas a working smoke
detector.
Do not use anelectrical extension cord with this fan. Do not plug
the fan into a power strip. The use of suchdevices may create

allow any foreign objects throughthe front of the case.
This product is not a toy. Do not allow children to tamper with
the fan.
Be careful not to allow hair, curtains, tablecloth, clothes or other
nearby objects block the airways of the fan or to enter the
openings of the fan. This can cause damage and/orinjuries.
Do not use this or any fan if the cord is found to be or becomes
damaged. Periodically check the electric cable of this fan.
If the electric cable is damaged, it must be replaced by the
2

person in order to avoid danger.
 Do not use this fan if itfalls and/or becomes damaged inany
way. If the fan becomesdamaged, it must be replaced by the
person in order to avoid danger.
 Do not use this fan outside, orin any commercial, industrial or
agricultural setting. This fan is only for residential use. Do not use
this fanwith any solid state speed control devices.
 Do not use this fan in a damp area such asa bathroom.
 Do not use this fan on a window, ledge, or on any unstable
platform. The fan should only be used standing on its base.
Never lay the fan on its side.
 Do not use this fan next to a window or anywhere where
exposure to rain ormoisture is possible. This may create an
electric hazard.
 Do not place the electrical cord under any objects, suchas
carpets, throw rugs or runners. Do not place electrical cord in
over it.
 The fan must always be unplugged when not in use. Before
 Do not operate the fanin an area where gasoline, paint supplies
stored.
 Do not try to repair or disassemble this fan. Doing so will void
the warranty and may result in damage and/or personalinjury.
There are noend-user serviceable parts.
 Remote control devices for other appliances may interfere with
this fanandvice-versa. If this occurs, move the fan to another
location.
 Always store the remote control inside the fan’s remote control
compartment.
 This fan is not suitable for use in agricultural facilitiesand
hazardous locations. Thisfandoesnot meet the requirements of
NEC Article 547-7 and 500 (2002).
 Keep this fan and all electrical appliances out of reachof
children at all times.
children unsupervised with access to this fan. There are no serviceable parts in
this fan. Do not attempt to disassemble or repair this product.
3

Parts of the Fan
1.Remote Control Compartment
with Control Panel
2.LCD Display
3.Grille
4.Extension Column (can be used
to extend the height of the fan)
5.Base
6.Remote Control
Assembly Instructions
Check contents – keep packaging
anduser instructions for future
reference.
NOTE: For shipping purposes,
the support column and the
base both have 2 separate halves
which need to be assembled.
4
STEP 1:
Assemble the extension column by
and snapping them together. If you
wish to use the fan without the added
height, proceed to Step 2, followed by
Step 4.
STEP 2:
half-circle plastic pieces and sliding
them together so that they interlock.
STEP 3:
fan body. Hold the support column upright (the side with screw
holes on top) and thread the power cord through it. Bring the
support column up to the bottom of the fan’s main body and

5
align the support column to the main fan
body so that the screw holes on both pieces
are matching. Secure with ¼”screws provided.
STEP 4:
in Step 3 in a similar fashion. Hold the base
upright (the side with a smooth surface) and
thread the power cord through the center hole.
Bring it up to meet the extension column and
ensure that the screw holes on both are aligned.
Secure together with nut wing-nut screws
provided. If using without the extension column, attach
directly to main fan body.
COMPLETED FAN (WITH EXTENSION COLUMN)
CAUTION: THIS FAN MUST OPERATE IN THE UPRIGHT
POSITION ONLY. DO NOT LAY FAN ON ITS SIDE OR IN
ANY OTHER POSITION. DOING SO MAY CAUSE DAMAGE
TO THE FAN AND/OR PERSONAL PROPERTY. DO NOT
USE THIS FAN WITHOUT ITS BASE.
Operating Instructions
1. Remove the cable tie and unravel the cord set before
operation.
2. DO NOT use outdoors.
3. Plug fan into a 120v, 60Hz outlet.
The control panel and the remote of this fan are equipped
with an LCD display and 6 functions (Power, Speed,
Oscillation, Timer+, Timer- and Mode). For your convenience,
the buttons on the remote are designed to function in the
same way as the keys on the fan’s control panel. The LCD
display has lights that illuminate to indicate the fan’s active
functions.
Press this button to power the fan ON. When the fan is
ON, the power light on the LCD display will be illuminated. Once
the fan is ON, you may proceed to set the following functions. To
power OFF, press this button again.

6
Osc: To activate the oscillation
function for widespread breeze
distribution, simply press this
function for a targeted breeze
setting, press the button again.
Timer+: This button sets the
duration of operation before
the fan automatically turns OFF.
Pressing this button will increase
the time of operation in 1 hour
increments to a maximum of 12
hours. The total time selected
is indicated by the light(s)
illuminating at 1H, 2H, 3H, etc.,
on the LCD display.
Timer-: This button sets the duration of operation before the
fan automatically turns OFF. Pressing this button will decrease
the time of operation in 1 hour decrements from 12 hours to a
minimum of 1 hour. The total time selected is indicated by the
light(s) illuminating at 1H, 2H, 3H, etc., on the LCD display.
Speed: Choose from 3 comfort settings (HIGH, MED, LOW) by
pressing this button until the speed you want is indicated on the
LCD display.
Night Mode LCD:
all icons on the LCD are dimmed except for the moon icon.
To activate the night mode feature, press and hold the MODE
button on the fan’s control panel for 3 seconds. To deactivate,
Mode: Choose from 3 dierent breeze patterns (Sleep, Nature,
Normal) by pressing this button until the type of breeze desired is
indicated on the LCD display.

Color LCD Display
Note: For fans purchased in the USA, the LCD will display the
room temperature in Fahrenheit.
Guidelines for using the remote control
 The remote control must be pointed towards the receiver on
the fan in order to work.
 The remote control may not operate in a room where a heavy
machine is operating.
 Do not block the line of sight between the remote control and
the receiver.
 Handle the remote control with care. Do not drop the remote
Guidelines for use of batteries
 If the remote control will not be used for a long period of time,
remove the batteries from the battery compartment.
 The remote conttrol uses two AAA batteries, both of which
should be new and replaced at the same time when they run
out.
 Clean the battery contacts and also those of the device prior to
battery installation.
 Ensure the batteries are installed correctly with regard to
polarity, matching +/- sides of the battery to corresponding
indications on the remote control.
 Remove used and dead/discharged batteries promptly.
7
F
F
Active

 Model Number: OZF1
 Voltage: 120V / 60Hz
 Wattage: 55 Watt
 Oscillation Angle: 80˚
 Weight: 4.70 kg (10.3 lb)
 Fan Plug Fuse Type: 2.5 Amp, 125 Volt
 Dimensions: D31cm x W31cm x H105 cm
(H89 cm without extension column)
CAUTION: THIS FAN HAS A POLARIZED PLUG (ONE BLADE
IS WIDER THAN THE OTHER). TO REDUCE THE RISK OF
ELECTRICAL SHOCK, THIS PLUG IS INTENED TO FIT IN A
POLARIZED OUTLET ONLY ONE WAY. MATCH THE WIDE
BLADE OF THE PLUG TO THE WIDE SLOT OF THE OUTLET.
FULLY INSERT. IF THE PLUG DOES NOT FIT FULLY IN THE
OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT,
CONTACT A QUALIFIED ELECTRICIAN. DO NOT ATTEMPT TO
BYPASS THIS SAFETY FEATURE.
NOTE: THIS FAN IS EQUIPPED WITH A FUSE. ALWAYS UNPLUG
THE FAN BEFORE REPLACING FUSES. IF THIS FAN LOSES
POWER AND YOU SUSPECT THE FUSE IN THE PLUG HAS
BLOWN, UNPLUG THE FAN, THEN SLIDE THE FUSE DOOR
FOUND ON THE SIDE OF THE PLUG TO THE OPEN POSITION.
SLIDE THE FUSE DOOR OUTWARD UNTIL THE BLOWN FUSE
IS FULLY VISIBLE. REMOVE THE BLOWN FUSE AND SNAP THE
REPLACEMENT FUSE INTO PLACE. FULLY CLOSE THE FUSE
DOOR. ONLY REPLACE WITH A FUSE RATED AT 2.5 AMPS,
125 VOLTS.
8

Cleaning Instructions
1. Always disconnect the cord from the electrical outlet before
cleaning your fan.
2. Dust may be removed by using a vacuum cleaner along the
back of the fan where the plastic grille covers the air intake.
3. Wipe the exterior surfaces of the fan occasionally with a damp
cloth (not dripping wet) and dry thoroughly with a soft dry
cloth before operating the fan.
4. Do not use harsh cleaners or materials to clean this unit, doing
so will cause damage.
CAUTION: DO NOT ALLOW WATER TO RUN INTO THE
INTERIOR OF THE FAN AS THIS COULD CREATE A FIRE OR
ELECTRIC SHOCK HAZARD. THE FAN MOTOR IS FACTORY
LUBRICATED FOR LIFE AND WILL REQUIRE NO FURTHER
LUBRICATION. NO OTHER USER MAINTENANCE IS REQUIRED
OR RECOMMENDED. IF SERVICE IS REQUIRED, SEND YOUR
FAN TO THE NEAREST AUTHORIZED SERVICE CENTER.
To Store
1. Follow cleaning instructions 1-4 above.
2. Retain the original packaging to store your fan.
3. Always store in a dry place.
4. Never store while still plugged in.
5. Never wrap cord tightly around the fan or put any stress on the
cord where it enters the fan as it could cause the cord to fray
or break.
Troubleshooting
If your fan fails to operate, please follow these procedures prior
to contacting customer service:
9

PROBLEM PROBABLE CAUSE SOLUTION
Fan is not
turning on.
A. Fan is not
plugged into a
120V AC, 60Hz
polarized outlet/
receptacle.
B. Breaker/fuse has
been tripped.
C. Fuse inside plug
of fan is blown.
A. Ensure unit is in the OFF
position. Plug in unit
and attempt to turn on
again.
B. Please check your
electrical box to
has not been “tripped”.
Ensure unit is in OFF
position. Plug in unit
and attempt to turn
on again. Attempt to
plug unit in another
receptacle in the house
C. First unplug fan from
outlet, then replace
fuse by following
fuse replacement
instructions in this
manual.
Fan is on but
air coming
out of it is
not strong
enough.
There is dust build
up at the back of
the fan.
Turn fan OFF and unplug.
Using a crevice tool
attachment, vacuum over
the grilles located at the
back of the fan to remove
dust build-up. Plug in unit
and turn fan back ON to
resume normal operation.
10