Rabbit Air BioGP SPA-421A User manual

User's Guide
Model No. SPA-421A and SPA-582A
www.RabbitAir.com
RabbitAir
TM

1
TM
•Read all instructions before using the BioGP air purifier.
TM
•Use only as directed by the BioGP air purifier user's guide. To reduce the risk of electric shock, do not attempt to service the product
in any way other than in the manner described in this user's guide.
TM
•Please observe extreme caution when the BioGP air purifier is used by or near children.
TM
•The BioGP air purifier is for indoor use only.
TM
•BioGP air purifier operates at 120V AC and 60Hz only.
TM
•The BioGP air purifier is not intended for use in bathrooms, laundry areas and other damp indoor environments. Keep the BioGP
air purifier away from water at all times. Never place the unit anywhere near bathtubs or sinks.
TM
•Do not use the BioGP air purifier near fireplaces or in areas where flammable or combustible products or vapors may be present.
TM
•Turn off the BioGP air purifier before unplugging it from power outlet.
TM
•Always unplug the BioGP air purifier from power outlet when not in use and before servicing or cleaning the unit.
TM
•To reduce the risk of electric shock, the BioGP air purifier has a polarized plug. This plug will fit in a polarized outlet only one way. If
the plug does not fit into the outlet, reverse the plug. If it still does not fit, contact qualified personnel to install the proper outlet. Do
not alter the plug in any way.
TM
•To reduce the risk of electric shock, do not touch the BioGP air purifier or its power plug with wet hands.
TM
•Always keep the BioGP air purifier cord away from heated surfaces.
TM
•Do not operate BioGP air purifier if the plug or cord appears damaged or is damaged. Return the unit to authorized service facility
for examination and repair.
TM
•Any attempts to open or repair the BioGP air purifier without written permission from Rabbit Air will void the warranty and could
cause serious personal injury to the user and/or result in severe damage to the unit.
•Do not use the power cord to lift, pull, carry or drag the BioGP air purifier, Avoid pulling the power cord against or around sharp
corners or edges.
TM
•Do not unplug the BioGP air purifier by pulling its power cord. Remove the power plug from its outlet by grasping the plug itself and
pulling gently.
TM
•When the BioGP air purifier plugs into the power outlet, do not put any object into the openings of the unit. Also keep all fingers,
body parts, hair, jewelry and loose clothing away from the openings.
TM
TM
WARNING: When using electrical appliances, basic precautions should always be followed to
reduce the risk of fire, electric shock, and injury to persons, including the following:
Safety Instructions

2
TM
Cautions Concering the Operation of BioGP Air Purifier
•Do not block the intake and air outlet.
•Do not use the unit near or on hot objects such as a stove.
•Do not use the unit where it may come into contact with steam.
•Do not use the unit on its side.
•Do not install the unit in a location where there is heavy generation of oily residue such as kitchen.
•Do not use detergent or soap to clean the unit.
•Do not operate the unit without installing the filters.
TM
•Do not wash & reuse the BioGP HEPA filter.
•When transporting the unit, always hold the handle on the back of the unit.
Remote Control Limitations
•Do not use the remote control near inverter lighting equipment or electronic light fixtures.
•Avoid leaving the remote control in direct sunlight. Heat may interfere with remote control signals.
Installation Guidelines
•Keep a distance of at least 3 feet of space between air purifier and any equipment which involve electric wave such as televisions,
radios or wave clocks.
TM
•Leave at least 2 inches of space between the wall and the BioGP air purifier.
TM
•Avoid locations where BioGP air quality sensors are exposed to direct wind.
•Avoid locations where excessive dirt comes into contact with the intake or air outlet.

3
Front View of Air Purifier
Air Outlet
Odor/Chemical Sensor
Detects odor such as
tobacco smoke, pets,
household chemicals
and etc.
Main Unit Display
Indicator lights and main control
button for the air cleaner.
Filter Reset Button
After replacing or cleaning the
filters, press the filter reset
button to reset the indicators.
Dust/Particle Sensor
Detects dusts, smoke, pollen,
animal dander and etc.
Washable charcoal based
activated carbon filter
Absorbs and removes common
household odors, VOCs,
chemical smells & cigarette odor.
TM
BioGP HEPA Filter
"Next Generation" HEPA filter
made of bio-engineered fiber
traps and destroys the allergens
such as pet dander, dust mite
and pollen which accumulate on
the filter.
Nano-Silver Pre-Filter
Aids in Sterilization and collects
pet hair, Large size allergens
and dust.
Front Panel
Part Names
Back View of Air Purifier
Handle
Slot to place remote control
Power cord
Power plug

4
Main Unit Display
Remote Control Operation
Transmitter Standby Button
Pressing this button will put the unit to standby mode.
Negative Ion Mode Button
Unit will generate negative ion by pressing this button.
Turbo Mode Button
Unit will operate at the highest fan speed for 10 minutes
and then changes to Auto mode.
Pollen Mode Button
This mode of operation is good for the pollen season.
The unit will alternate between low and medium fan
speed every 10 minutes
Fan Level Button
The fan speed can be switched between Low, Medium,
High and Turbo.
Auto Mode Button
Silent or Sleep Mode Button
Timer Button
The fan speed of the air cleaner will
change automatically depending on the
amount of impurities in the air as detected
by the dust and odor sensors.
Unit will operate at a lower fan speed and
the operation is totally silent.
Us d to set the Off Timer.
The set time switches every time the button
is pressed as shown below.
e
1 hours 2 hours
off timer
4 hours
The indicator light shows the remaining time.
The unit stops operating when the timer is up.
Remote Control Receiver
RabbitAir
Negative Ion Indicator
Unit will generate negative ion when this
indicator is on.
Filter Cleaning Indicator
The filter cleaning indicator will illuminate
when it is time to clean the filters and reset
the indicator.
Filter Replacement Indicator
The filter replacement indicator will illuminate
when it is time to replace the filters and reset
the indicator.
Particle/Dust Level Indicator
Indicates level of dust or patricles by
changing color in five steps from light green,
green, yellow, orange to red. (Light Green
represents good air quality & Red represents
poor air quality)
Fan Level Indicator
Indicates the fan speed of the air purifier.
Main Control Button
You can change operation modes, turning
the unit on and off or changing the fan
speed of the unit by using this control button.
Operation Mode Indicators
Indicator lights for Auto Mode, Turbo
Mode, Sleep Mode and Pollen Mode.
Timer Display Indicator
Unit will turn off automatically after pre-
set time duration.
Odor/Chemical Level Indicator
Indicates chemical and odor levels by
changing color in five steps from light
green, green, yellow, orange to red.
(Light Green represents good air quality
& Red represents poor air quality)
Unit Status Indicator
Unit status indicator will stay on when the air purifier
is on standby or is operating. The indicator will flash
for 15 seconds when the air purifier is detecting the
air quality baseline.

5
Preparation
List of Parts
Remote Control
1. Filter Installation
CAUTION
To maintain the quality of the filters, they are placed in the unit within plastic bags.
Please remove the filters from the plastic bags before using the unit.
Step 1 Place the unit facing up and Remove the front panel
Lay the unit on a flat surface such as table or floor. Make sure not to pinch the power cord on the rear of the unit.
Put your hands at the bottom of the front panel and lift the panel up gently.
Step 2 TM
Remove Plastic bags from the BioGP HEPA filter and Washable charcoal based
activated carbon filter.
Remove the pre-filter from the unit.
TM
Remove Plastic bags from the BioGP HEPA filter and Washable charcoal based activated carbon filter.
First, install the Washable charcoal based activated carbon filter. The filter handle should be facing the front panel.
Step 3 Re-insert the pre-filter and the front panel.
First, install the pre-filter. The filter handles should be facing the front panel.
Re-insert the front panel back to the unit. Press in the hooks on the bottom of the front panel into the unit.
You should hear a "click" sound if installed properly.
Inserting Battery in the Remote Control.
Flip over the remote control. Press and
slide out the battery holder
1Insert battery with positive side facing up. 2Close the battery holder. 3
Nano-silver
Pre-Filter
TM
BioGP HEPA
Filter
Washable charcoal
based activated
carbon filter
3V Lithium
Coin Battery
TM
Install the BioGP HEPA filter with the word "Front" on the filter frame face toward you.
1
2
1
2
3
4
1
2
Battery Information
The batteries for this remote control are for initial use only. Change the batteries when necessary.
Incorrect usage of the batteries may cause battery fluid leakage and/or damage.
When replacing battery, replace battery with new one of the same type (Use 3V Lithium Coin Battery).
When not using the unit or remote control for an extended period, remove the batteries.
(This prevents malfunction of the remote control from battery fluid leakage.)
The batteries are for initial use only and may be depleted within 1 year.
RabbitAir

6
How to set up Home Air Quality Baseline.
When the power plug is inserted into the wall outlet, the unit will register the current home air quality as a baseline (reference point).
It will take 15 seconds for the Air Quality Level Sensors to indicate the air quality level. You will see the unit status indicator on the
main unit display flashing for 15 seconds.
The Air Quality Level Indicator displays a color-coded indicator light depending on relative changes to the environment from the
time the power plug is inserted into the wall outlet and thereafter.
The Air Quality Level Indicator can be turned off using the Standby button on the remote control.
Important
When the air is heavily polluted at the time the power plug is inserted, the unit may not work properly in auto mode because
the baseline or reference point is too high. To reset the air quality baseline, unplug the unit and re-insert it when the air
quality is in normal condition.
Operation
1. Remote Control
2. Main Unit Control Button. (Some features will not be available by using just the unit control button.)
Unit can operate by using either:
The remote control or main unit control button can activate the following modes.
Automatic mode
Silent mode
Manual mode
1
2
3
Start operation.
Auto mode Unit automatically select fan speed based on air quality.
Remote Main
1
2
3
4
5
6
7
Turbo mode Unit operates at turbo speed for 10 minutes and then returns to auto mode.
Silent mode Unit operates at the lowest and the quietest fan speed.
Manual mode Unit operates at the pre-set fan speed.
Pollen mode The unit will alternate between low and medium fan speed every 10 minutes.
Timer mode Unit operates for a pre-determined time, then shuts off.
Negative Ion mode Turns negative ion generator on/off.
Remote control operation
Activate remote control by pressing the any button. Be inline with the front side of the
unit. (The maximum range of effectiveness is 23 feet)
Avoid exposure to direct sunlight; inverter lamp and high frequency equipment. It might
affect performance of remote control.
If air purifier responds properly, a short beep will sound and operation will start.
Please try to replace the battery if the remote control does not work properly.
r
aAi bitRb

7
Auto Mode
The fan speed of the air cleaner will change automatically depending on the amount of impurities in the air as
detected by the dust and odor sensors.
Press the Auto Mode button on the remote control to start the Auto Mode operation.
Strat operation
Air Quality
Level Indicator
Fan Speed Silent Low Med High Turbo
Mode of Operation
ATTENTION
When the air is heavily polluted at the time the power plug is inserted, the unit may not work properly in
auto mode because the baseline or reference point is too high. To reset the air quality baseline, unplug
the unit and re-insert it when the air quality is in normal condition.
The unit will operate at silent fan speed when the air quality level is normal or is below the baseline level.
Turbo Mode
The air purifier operates at turbo fan speed for 10 minutes and
then changes to Auto mode.
Press the Turbo Mode button on the remote control to start
the Turbo Mode operation.
First 10 Minute After 10 Minute
Mode of
Operation
Silent Mode
The air purifier operates at silent fan speed continuously.
Press the Silent Mode button on the remote control to start
the Silent Mode operation.
Silent Mode
Turbo Mode
Mode of
Operation
Manual Mode
The air purifier operates at the selected fan speed continuously.
Press the Fan Level Button on the remote control to start the
Manual Mode operation.
Manual Mode
Mode of
Operation
Low Medium
High
Turbo
1
2
3
4
RabbitAir

8
Pollen Mode
This mode of operation is recommended for the pollen season.
The unit will alternate between low and medium fan speed every
10 minutes.
Press the Pollen Mode button on the remote control to start
the Pollen Mode operation.
Pollen Mode
Mode of
Operation
Timer
settings
Timer Mode
Timer Mode
The unit will stop operating when the timer is up.
Press the Timer Mode button on the remote control to start
the Timer Mode operation.
Used to set the Off Timer.
The set time switches every time the button is
pressed as shown below.
1 hours 2 hours
off timer
4 hours
The indicator light shows the remaining time.
The unit stops operating when the timer is up.
Negative Ion Mode
Unit generates negative ion by pressing Negative Ion Mode
button.
Negative Ion Mode
Mode of
Operation
ATTENTION
TM
The BioGP Air Purifier produces millions of healthy
"negative ions" to improve the air you breathe and freshen
your indoor environment through the use of anion
generator inside of the unit discharge. The negative ions
help reduce suspended particulate, and at the same time,
make it difficult for pollutants to become airborne in the first
place. Negative ions are odorless, tasteless, and invisible
molecules that we inhale in abundance in certain
environments. Think mountains, waterfalls, and beaches.
Scientific research shows negative ions may help to
alleviate depression, relieve stress, and boost our daytime
TM
energy. The Rabbit Air BioGP air purifier uses non-ozone
clusters to produce negative ions, therefore, our unit has
zero ozone emission and it is harmless to human and the
environment.
Standby
Press the Standby button on the remote control to stop the unit.
5
6
7
8
RabbitAir

9
Main Unit Control Button
You can control the air purifier by the main unit control button. When you press
the button, the operation mode of the air purifier will be changed according to
the following diagram.
Cleaning and Maintenance
Auto Mode Silent Mode Low Speed Medium Speed High Speed Turbo Speed Standby
To maintain optimum performance of this product, please clean the unit and filters as recommended.
CAUTION
When cleaning the unit, be sure to unplug the power cord, and never handle the plug with wet hands.
Electrical shock and/or bodily injury may occur as a result.
1. Cleaning the Unit Surface and Air Quality Sensors
The unit surface should be cleaned at least once a month or sooner depending on the air
quality of the room.
Use a clean, dry cloth to wipe the external surfaces of the air purifier.
Use a damp cloth to remove stubborn stains and dirt build up if necessary.
Do not use commercial cleaning agent as it may damage the unit surface.
Clean the air inlet and outlet with a dry cloth or a vacuum cleaner. (Fig. 1)
To clean the unit surface:
(Fig. 1)
The air quality sensors should be cleaned at least once a month or more depending on
the air quality of the room.
Take off the front panel.
Clean the surface of the sensor opening with a vacuum cleaner.
To clean air quality sensors:
2. Cleaning the Pre-Filter
The pre-filter should be cleaned at least once a month or when the filter cleaning indicator
illuminates.
After removing the front panel from the air purifier, run a vacuum cleaner with a nozzle or
brush attachment on low power setting along the filter to pick up the pet hairs or particles.
(Fig. 2)
To clean the pre-filter:
(Fig. 2)

10
TM
3. Cleaning the BioGP HEPA Filter
TM
The BioGP HEAP filter should be cleaned when the filter cleaning indicator illuminates.
After removing the pre-filter from the air purifier, run a vacuum cleaner with a nozzle or brush
attachment on low power setting along the HEPA filter to pick up the dust and particles (Fig 4).
TM
To clean the BioGP HEPA filter:
4. Cleaning the Washable Activated Carbon Filter
To clean the washable activated carbon filter:
Remove the pre-filter from the unit. (Fig. 3)
Fill the sink with lukewarm water and gently wash the filter under the water for 2-3 minutes or until it is
completely clean.
Rinse the filter with clean tap water.
Use towel to remove any excess water from the filter.
Allow the filter to dry for a few hours or overnight.
When the filter is completely dry, place back into the air purifier.
If your pre-filter appears to have dirt that has not been removed by vacuuming, please follow
the steps below to wash the pre-filter.
(Fig. 3)
The activated carbon filter should be cleaned when the filter cleaning indicator illuminates.
Remove the filter from the unit.
Fill the sink with lukewarm water and add a few drops of mild household detergent (Fig. 5).
Soak the filter for 10 minutes. Do not leave for an extended period of time.
Rinse the filter with clean tap water.
Use towel to remove any excess water from the filter.
Allow the filter to dry for a few hours or overnight.
When the filter is completely dry, place back into the air purifier.
To reset the Filter Cleaning or Replacement Indicator
Remove front panel.
With the power on, press and hold the filter reset button for 3-5 seconds, or until the "red" filter
cleaning or replacement indicator clears itself (Fig.6).
(Fig. 4)
(Fig. 5)
(Fig. 6)

11
TM
When the filter replacement indicator light comes on, replace the old BioGP HEPA filter with a new one.
To maintain optimum performance of this product, please replace the filters as recommended.
The air quality and surrounding environment determines the duration and life span of the filter and while it may last longer than
TM
expected, it is advisable to change the BioGP HEPA filter at least every 18 months or 1.5 year of unit operation.
The higher the level of pollutants, the shorter the lifespan of the filter.
TM
Replacing the BioGP HEPA filter
Remove the front cover and the pre-filter
TM
Install a new BioGP HEPA filer by following the instructions on step 1 and 2 (page 5).
After replacing the filter, reset the filter replacement indicator as indicated in page 10.
Follow the instruction on step 3 (page 5) and complete the filter change.
1
2
3
4
ATTENTION
TM
Discard the used BioGP HEPA filter and do not store for re-use.
TM
For more information on the BioGP HEPA filter replacement or to buy replacement filter,
please contact Rabbit Air.
Replacing the washable activated carbon filter
Replacement indicator light will come on every 18 months, the washable activated carbon filter only need to be replaced every
other time when the indicator light comes on. A single filter can last up to 3 years.
To maintain optimum performance of this product, please replace the filters as recommended.
The air quality and surrounding environment determines the duration and life span of the filter and while it may last longer than
expected, it is advisable to change the washable activated carbon filter every 3 years.
The higher the level of pollutants, the shorter the lifespan of the filter.
Remove the front cover and the pre-filter
Install a new washable activated carbon filter by following the instructions on step 1 and 2 (page 5).
After replacing the filter, reset the filter replacement indicator as indicated in page 10.
Follow the instructions on step 3 (page 5) and complete the filter change.
1
2
3
4
ATTENTION
Discard the used washable activated carbon filter and do not store for re-use.

LIMITED WARRANTY
12
SPA-421A/582A
TM
Rabbit Air warrants that your BioGP Air Purifier will be free from defects in material or workmanship for a period of Five (5) years
from the date of purchase. To activate the warranty, please complete and return your warranty registration within 30 days of purchase
TM
of your air purifier to Rabbit Air. In order to ensure unit performance, the filters should be replaced with original BioGP replacement
filters as recommended in this manual (the 'Limited Warranty'). Otherwise the standard warranty time in your country applies.
Within the first 30 days of purchase, Rabbit Air will replace the defective unit at no additional cost and reimburse any shipping
charges. After 30 days, Rabbit Air's obligation and liability under this Limited Warranty is limited to repairing or replacing (at its sole
discretion) the defective unit. The Limited Warranty does not cover replacement filters.
TM
In the event of a malfunction or failure of your Rabbit Air BioGP Air Purifier, please contact Rabbit Air to obtain a return authorization
number and the address of the service center. The return authorization number must be clearly written on the outside of the shipping
box or the shipment may be refused.
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF
THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING
THE WARRANTIES OF MERCHANTABILITY, AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE APPLICABLE
WARRANTY PERIOD SET FORTH ABOVE.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to
you.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
If a problem with the product develops during the warranty period, we will repair or replace it without charge to you. A shipping and
processing fee may apply. To obtain service under warranty, please contact Rabbit Air at 1-888-866-8862 or by email at
[e-mail]
LIMITS AND EXCLUSIONS
1. Is operated in accordance with the instruction provided.
2. Is connected to a proper power supply (see voltage label on machine).
TM
3. Three is no evidence of tampering, mishandling, neglect, accidental damage, modification, and/or repair done to the BioGP Air
TM
Purifier by anyone other than authorized BioGP service personnel.
4. Your warranty registration has been completed and returned to Rabbit Air.
TM
Your Limited Warranty remains in effect only if your BioGP Air Purifier:
RabbitAir Ultra Quiet Air Purifier

13
Troubleshooting
Before calling for repair, please review the list below. The problem may not be due to unit malfunction.
Symptom Solution
Unit does not operate. Check if power plug is loose.
Press the main unit control button or any buttons on the remote
The remote control does
not work.
Check if the battery has been depleted. (Refer to P.5)
Check if the battery is inserted correctly. (Refer to P.5)
Point the remote control directly towards the main unit display.
Fluorescent lighting flickering in the room may affect the signal of the remote control. Please service the
fluorescent lights.
Odors and smoke are not
removed.
Clean the filters if they appear to be heavily soiled. (Refer to P.9)
Check if all the plastic bags that wrap the filters are being removed. (Refer to P.5)
The unit does not operate
when cigarette smoke is
in the air or when the air is
highly polluted.
Check if the unit is installed in a location that is difficult for the sensors to detect the smoke or the air quality.
Check if the odor or dust sensor openings are blocked or clogged. Clean the sensors (Refer to P.9)
The unit may not work properly in auto mode because the baseline or reference point is too high. To reset
the air quality baseline, unplug the unit and re-insert it in a well-ventilated area.
In auto mode, the unit
operates at high speed
even when the air is
clean.
The sensitivity of the sensor becomes unstable when the sensor opening is blocked or clogged. Clean the
sensors (Refer to P.9).
Reset the air quality baseline, unplug the unit and re-insert it.
The filter replacement
indicator light remains
activated even after
replacing filter.
After replacing filters, connect the power cord to an outlet and press the filter reset button on the main unit.
With the power on, press and hold the filter reset button for 3-5 seconds, or until the "red" filter cleaning or
replacement indicator clears itself (Refer to P.10).
The negative ion mode
indicator light is flashing.
Clean the negative ion generator inside the discharge outlet with a vacuum cleaner.

1. 1. Mr. 2. Mrs. 3. Ms. 4. Miss
First Name Initial Last Name
Street
City
E-mail
Apt. No.
State/Province ZIP/Postal Code
2. Your date of birth:
Month Year
3. Marital status: 1. Married 2. Single
4. Date of purchase:
Month YearDay
5. Model number: (please refer to owner's manual or the back
of your product to locate the model number)
6. Serial number:
7. Name of store where purchased:
8. Do you own a house or rent?
9. Where did you first learn about Rabbit Air
products?
1. Received as a gift
2. Newspaper
3. Salesperson
4. Friend/Relative
5. Online
6. Magazine
7. Prior experience with Rabbit Air brand
8. TV
9. Other
11. What is the primary reason you purchased this
product? (Check only one)
1. Relieve Allergy or Asthma Symptoms
2. Improve Air Quality for Kids
3. Improve Home Comfort in general
4. Germicidal Protection/Relieve Cold &
Flu Symptoms.
5. Reduce Smoking Odors in House
6. Reduce Pet Odors
7. Reduce Cooking Odors
8. Other
12. Where do you plan to use this Rabbit Air product?
(Check all that apply)
1. Living Room
2. Bedroom
3. Child's Room
4. Family Room
5. Kitchen
6. Office
7. Hallway
8. Bathroom
9. Home workshop area
10. Other
13. Which group describes your annual family income?
1. Under $29,999
2. $30,000-$39,999
3. $40,000-$49,999
4. $50,000-$59,999
5. $60,000-$74,999
6. $75,000-$99,999
7. $100,000-$124,999
8. $125,000-$149,999
9. $150,000-$174,999
10. $175,000-$199,999
11. $200,000-$249,999
12. $250,000 & over
10. What factors most influenced your decision to
purchase this Rabbit Air product?
(check up to 3)
1. Rabbit Air reputation
2. Prior experience with Rabbit Air
3. Value for the price
4. Quality
5. Size/dimension
14. Level of education: (check highest level completed)
1. Completed High School
2. Completed College
3. Completed Graduate School
www.RabbitAir.com
RabbitAir
Ultra Quiet Air Purifier
Country
Own Rent
15. If this product was available in different color, which
color would you prefer?
16. Are there other features that you would like to see on
this product?
6. Style/appearance
7. Product availability
8. Advertisement
9. Other

Please do not send products or
other correspondences to this address First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
WARRANTY REGISTRATION FOR
RETURN THIS CARD NOW FOR:
201 West Garvey Ave., Suite 102-168
Monterey Park CA 91754-7418
Product Protection
Copyright ©2007 All Rights Reserved
Please fold and seal with tape before mailing. Do not staple.
With the information you provide we can confirm the date of purchase of your product.
This confirmation is of benefit to you, especially if your original proof of purchase is lost.
Proof of Ownership
Your model number, serial number, and other information will be kept in our files.
Or register online at: www.RabbitAir.com
Please complete and return this registration within 30 days at purchase in order to receive
your 5 year Limited Warranty.
RabbitAir
Ultra Quiet Air Purifier