Racelogic RLACS277RLACS29 User manual

Quick Start Guide: Accel Mode - Performance Box Touch V1
https://en.racelogic.support//Product_ nfo/Performance_Meters/Performance_Box_Touch/
Performance_Box_Touch_V1/Quick_Start_Guide_%E2%80%93_Performance_Box_Touch_V1/
Quick_Start_Guide%3A_Accel_Mode_-_Performance_Box_Touch_V1
Performance Box Touch V1 features a 10 Hz GPS receiver and a responsive 4.3” colour touch screen.
The Accel Mode allows you to perform acceleration tests using either pre-defined configurations or your own specified
values.
Registration
Please register your Performance Box Touch so that Racelogic can continue to inform you about the latest software
releases and firmware upgrades and offer technical support.
Register your unit here.
What’s in the Box
Performance Box Touch V1 (RLPBT-V1)
Product Code Quantity Description
PBT-V1 1 Performance Box Touch Unit
RLACS184 1 Cigar Plug USB Adapter
1

Product Code Quantity Description
USB2-007241 1USB 2.0 A to Right Angle Micro B
data and Charging Cable, 1.5 m
RLACS313 18 GB SD Ultima Pro UHS-1 Memory
Card
RLACS277 1 Swivel Neck Richter Suction Mount
Performance Box Touch V1 Bundle (RLPBT/B)
Product Code Quantity Description
PBT-V1 1 Performance Box Touch Unit
RLACS184 1 Cigar Plug USB Adapter
USB2-007241 2USB 2.0 A to Right Angle Micro B
data and Charging Cable, 1.5 m
RLACS313 18 GB SD Ultima Pro UHS-1 Memory
Card
RLACS277 1 Swivel Neck Richter Suction Mount
RLACS290 1 Performance Box Touch Battery
2

Product Code Quantity Description
RLACS284 1GPS/GLONASS Low Profile
Antenna, 2 m
RLACS281 1 Plastic Carry Case
Hardware Overview
You can find more detailed connector information on the PIN OUTS page.
Left Side
Right Side
Logging
Performance Box Touch V1 logs data via an SD card inserted into the SD cad Slot on the left-hand side of the unit.
3

Depending on the Logging Strategy you have selected in the General Settings area, the unit will either
log continuously or when it detects movement.
You can manually override the configured logging strategy by tapping on the SD Card Icon when it is
green to start or stop the logging.
The Record Icon will show when the unit is logging data to the SD card.
f you have come to a stop, but the Record Icon is still on, you must press the SD Card Icon to stop
the logging before you remove the SD card.
Sometimes, due to poor satellite visibility, for example in a garage or close to a building, the box may start
recording even if the car is stationary. Always check the Record Icon to make sure the box is not recording
before you eject the card.
IMPORTANT
The SD card should not be removed when the Record Icon flashes red as it may cause you to lose
data.
Note: If the SD card is removed while the box is still recording, you may need to repair it on a PC before
you can use it again.
SD Card Format
Performance Box Touch is supplied with an 8 GB SDHC card in a FAT32 file format, which is the only file format it
supports.
f you are looking to purchase a new SD card, we recommend that any card you use has a write speed of above 7
MB/s (4 MB/s is the absolute minimum) and a speed class of 10 (4 is the absolute minimum). We recommend that
you use SD cards from quality brands such as Transcend, SanDisk, Kingston or Lexar to ensure the best results.
IMPORTANT
If you have an SD card that is formatted in the exFAT or NTFS file formats, you will have to reformat it to a
FAT32 file system before it will work with a Performance Box Touch unit.
4

SDHC cards (2 GB to 32 GB)
Supplied or purchased SDHC cards are formatted in the FAT32 file format. This format is
supported by Performance Box Touch.
SDXC cards (64 GB and above)
Purchased SDXC cards will be formatted in exFAT or NTFS file formats; these formats are not supported by
Performance Box Touch. Please reformat as per the instructions below.
SD Card Reformatting
• FAT32 reformatting for media with sizes up to 32 GB can be done directly in Windows by right-clicking on the
media and selecting 'Format'.
• f you would like to format media with sizes above 32 GB into a FAT32 file system, you cannot do it directly in
Windows as it is not the standard formatting for the file. However, there are many third-party software programs
you can use to reformat media so that they will work correctly with our products - we recommend This Tool as
a free option from the SD card organisation.
Logged Channels
Performance Box Touch logs channels to a .vbo file on an inserted SD card. The channel information is as follows:
•Satellites: This is the number of satellites in use.
•Time: This is UTC time since midnight in the form HHMMSS.SS.
•Latitude: Latitude in minutes MMMM.MMMMMMMM +ve = North e.g. 3169.30644410M = 52D, 49M, 18.4S.
•Longitude: Longitude in minutes MMMMM.MMMMMMMM +ve = West e.g. 00040.18164742M = 00D, 40M,
10.9S.
•Velocity: Velocity in km/h.
•Heading: Heading in degrees with respect to North.
•Height: Height above sea level in meters based on the model of the earth used by thye VBOX GNSS engines.
•Vertical velocity: Vertical velocity in km/h. +ve velocity uphill, -ve velocity downhill.
•Long accel: Longitudinal acceleration in g, +ve for forward acceleration.
•Lat accel: Lateral acceleration in g, +ve for acceleration to the left.
•Solution type: ndicator for what the unit is currently using to derive position: 0 = No sats; 1 = Standalone
using GNSS only; 2 = SBAS.
5

You can find more information on the VBO file format here.
Screen Overview
Setup
1. Performance Box Touch V1 has an internal patch antenna. This means that where the unit has a clear view of the
sky without any interference, an additional antenna is not required in most circumstances.
However, if it is required, you should mount the external GPS antenna (RLACS284) in the centre of the roof of the
vehicle, away from roof bars and other antennas. You can find more information about how to mount your external
antenna here.
2. f you are using an external antenna, connect it to the Performance Box Touch.
3. Connect the Battery (RLACS290) if required. You can find more information about the battery here.
4. Connect the Swivel Neck Richter Suction Mount (RLACS277) to the rear of the unit (or the battery if applicable)
and attach the suction mount to the vehicle's windscreen. You can find more information about the mounting of the
unit here.
5. Connect the power via the Power socket, or if you are using the battery independent of a power source, press
and hold the Power button on the battery for a few seconds.
6. nsert the SD card into the SD card slot. The SD Card Icon should display in green as long as the card has
available space.
6

7. When the unit has booted up, select the Mode Button and press ACCEL if it is not already selected.
8. Select which Accel screen you would like to display (Primary,Secondary or Best Result). Press
the Forward and Back arrows at the bottom right of the screen or swipe left or right to select.
Primary Secondary
7

9. Select the Settings Button, the Accel option and choose the Start and End Parameters of the 4 concurrent
tests. By default, these are 0–60, 0–100, 0–100–0 and 0–¼ mile.
10. f you would like an audible and visual alert when the test is completed or when the target speed is met during a
0-Speed-0 test, enable the Alert at End/Target in the Settings.
11. f you would like the test to start only after a distance of 1 ft or 0.305 m has been covered, enable One Foot
Rollout in the Settings.
Note: Cannot be used in conjunction with Slope Correction.
12. f you would like to apply DB Scanner slope correction method to the test, enable Slope Correct within the
Settings.
Note: cannot be used in conjunction with One foot rollout.
8

13. Press the Exit Button to return to the Accel Test screen.
14. Take the vehicle outside and wait for the Performance Box Touch to gain satellite lock.
The Satellite Icon should display as solid green .
Note: The first time that the unit is used, it may take up to 10 - 15 minutes to fully acquire satellites. After this, it will
usually take 1 - 2 minutes to acquire satellites.
15. The unit is now ready to display live Accel Test results.
16. By default, Performance Box Touch will automatically start recording when it detects moving in a speed of 0.5 km/
h or more. You can change this in the General Settings.
17. By tapping the SD Card Icon when it is green you can manually start or stop the logging of data and override the
Configured Logging Strategy.
18. The Record Icon will show when the unit is logging data to the SD card.
f you have come to a stop, but the Record Icon is still on, you must press the SD Card Icon to stop
the logging before you can remove the SD card.
Sometimes, due to poor satellite visibility, for example in a garage or close to a building, the box may start
recording even if the car is stationary. Always check that the Record Icon is not red before you eject the card.
IMPORTANT
The SD card should not be removed while the Record Icon is red as it may cause you to lose data.
Note: If the SD card is removed while the box is still recording, you may need to repair it on a PC before you can
use it again.
19. You can take a screenshot of what is displayed on the screen at any time by pressing the Screenshot Button.
20. You can reset all test results shown on the current screen by pressing the Reset Button.
21. When you have finished your testing, you can view your completed test results by pressing the Results Button.
9

You can find more information on Accel Mode testing here.
Data Analysis
The recorded session will be saved on the SD card as a .vbo file. You can do post-analysis on this file in the VBOX
Test Suite or Circuit Tools softwares, which you can download from the VBOX Motorsport Website. Features include
a graphical display of logged parameters, a full circuit plot, overlaid comparison laps and detailed performance analysis.
VBOX Test Suite Circuit Tools
10