Radia 5315 Speed Demon 5 User manual

Owner’s Manual:
5315 Speed Demon 5
Five-Gallon Vortex Mixer
Models 0-5315-PB (110V, 60 Hz Digital Display)
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
TM

2
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Table of Contents
Safety Information
1.1 Safety Precaution Labels
1.2 Saftey Precaution Summary
Introduction
2.1 Application
2.2 Specifications
Unpacking & Install
Operation
4.1 Control Panel
4.2 Install a Container
Care and Maintenance
5.1 Cleaning
1.
2.
3.
4.
5.
3
4
5
6
6
6
7
8
8
9
9
9
Trouble Shooting
Wiring Diagram
Exploded Views
8.1 Electrical Assembly
8.2 Enclosure Assembly
8.3 Drive, Bottom Assembly
8.4 Drive, Middle Assembly
8.5 Drive, Can Holder Assembly
8.6 Frame Assemblyl
Ordering
Replacement Parts
Warranty
6.
7.
8.
9.
10
11
12
12
13
14
15
16
17
18
18
19
10.

3
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
“WARNING!” indicates a hazardous situation, which, if not
avoided, could result in death or serious injury. These serious
injuries could include permanent loss of function or significant
disfigurement, disability, considerable pain and suffering,
amputations, se vere burns, and loss or impairment of vision or
hearing. Take all necessary precautions to avoid unnecessary
“CAUTION!” indicates a hazardous situation, which, if not avoided,
could result in minor or moderate injury.
“NOTICE” indicates practices that do not involve physical injury
but may damage the machine.
NOTICE
1. Saftey Information
Review this owner’s manual and read all warning labels on the machine prior to use.
The three main safety notifications used in this manual and on the warning labels are
WARNING, CAUTION and NOTICE. They have specific meanings and indicate the potential
dangers from misuse of the machine.
Safety Information, Continued..

4
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
1.1 Safety Precaution Labels
Safety Information, Continued..
Part No. 1780899
-This machine is not explosion proof rated.
-Review product label, Material saftey Data Sheet, and HMIS rating of
materials and exposures prior to mixing to determine potentional hazards.
-Use in dry and well-ventilated environment where dust and ammable
vapors are not present; risk of physical injury exists if used in hazardous
environment.
-All containers must be properly sealed and void of leaks.
-Esta máquina no tiene la clasicatión de prueba de explosion.
-Revise la etiqueta del producto, la hoja informativa de datos de
seguridad, su clasicatión HMIS antes de mezclar y exposiciones de
materiales peligrosos para determinar los peligros potenciales.
-Use en un ambiente seco y bien ventilado donde polvo y vapores
inamables no estên presentes; Riesgo de daño sco existe si es untilizado en
un ambiente peligrosos.
-Todos los contenedores deben estar bien sellados y sin fugas.
-Cette machine n'est pas classê antidêagrant.
-Examen e'tiquette du prodiut, Fiche de dane;es de se'curite', Et
mate'riel HMIS cote et expositions, avant de faire le me'lange pour
de'terminer les risques poteniels.
-Utilisation a'sec et bien aere' environnement ou'la possie're et les
vapeurs inammables ne sont pas presents; risque de blessure physique
existe si ultilise' en environnement dangereux.
-Tous les conteneurs doivent être concenablement scellês pour èviter
les fuites.
WARNING
ADVERTENCIA
AVERTISSEMENT
- Machine must be properly grounded before use; improper grounding could
cause electric shock and injury.
-Disconnect power cord before servicing, cleaning or removing any
cover, and follow lockout/ tagout procedures in owner manual; failure to
disconnect power could cause electric shock and injury.
-Review Owners Manual before installing or operating.
- La maquinaria debe ser apoyada correctamente en el suelo antes de usar,
el no apoyarla puede casuar choque elêctrico y daños.
-Desconecte la energía antes de dar mantenimiento, limpiar o quitar
caulquier cubierta, y siga los procedimientos de bloqueo/etiquetado del
manual, Fallar en desconectar puede causar choque eléctrico y daños.
- La machine doit e'tre correctement mis a' la terre avant de les utilizer
mise a' la terre incorrecte peut provoquer un choc e'lectrique et de
blessure.
- De'branchez le cordon d'alimentation avant de proce'der a'l'entretien,
le nettoyage ou le retrait des capots: suivez la proce'dure d'isolation/
consignation proce'dures dans le manul de l'opre'rateur; E'chec de
WARNING
ADVERTENCIA
AVERTISSEMENT
Part No. 1781570
Part No. 1784963
MOVING PARTS INSIDE
PARTES EN MOVIMENTO
PIE'CES EN MOVEMENT
-Do not open door until machine comes to complete stop;
moving parts inside could cause serious injury.
-No abra la puerta hasta que la marquina se detenga
completamente, las partes internas en movimiento pueden
causar heridas graves.
- Ne pas ouvrezla porte jusqu'a'ce que la machine esta
comple'tement arre'te'; pièces en mouvement à l'intérieur
pourrait provoquer des blessures grave.
WARNING
ADVERTENCIA
AVERTISSEMENT
Safety Information, Continued..

5
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
WARNING!
DO NOT attempt to replace any damaged
electrical wire or components. Improper
replacement could result in electric
shock and serious injury. Only a qualified
service representative should attempt to
repair or replace any damaged electrical
components.
Review this owner's manual before installing or
operating.
The machine must be properly grounded prior
to use. In the case of an electrical short circuit,
grounding reduces the risk of electric shock
by providing an escape wire for the electric
current.
The machine’s power cord has a grounding
wire with an appropriate grounding plug.
This plug must be inserted into an electrical
outlet that is properly installed and grounded
according to all local codes and ordinances.
If you must repair or replace the power cord
or plug, DO NOT connect the grounding
wire to either flat-blade terminal. The wire
with insulation having an outer surface that
is green (with or without yellow stripes) is the
grounding wire.
Check with a qualified electrician if you don’t
completely understand these grounding
instructions, or if you are not sure whether
the machine is properly grounded. DO NOT
modify the plug provided; if it won’t fit in the
outlet, have a proper outlet installed by a
qualified electrician.
Disconnect the power cord before servicing,
cleaning, or removing any covers
Follow the lockout/tagout procedures of your
company.
DO NOT open the door until the machine
comes to a complete stop.
CAUTION!
Keep the work area free of clutter and
electrical cords.
Avoid extension cords. To minimize the
risk of improper electrical grounding,
extension cords are not recommended. If
an extension cord is unavoidable, consult a
qualified electrician to determine what type
of extension cord will satisfy the grounding,
current capacity, and other requirements of
the particular situation.
Use the proper power source. Refer to
the machine data plate on the right side
panel or the section 2.2, Specifications, in
this manual.
Keep customers away from the work area.
The machine should be used only by
properly trained individuals.
Clamp the can carefully to ensure that it is
held securely during the mixing cycle.
To avoid electric shock, don’t get the timer,
control panel, or wiring wet.
This machine is not explosion proof rated.
All containers must be properly sealed and
void of leaks.
Review product label, Material Safety Data
Sheet, and HMIS rating of materials prior to
mixing to determine potential hazards.
DO NOT use solvent-based cleaners or
thinners.
Use in a dry and well-ventilated environment
where dust and flammable vapors are not
present.
1.2 Safety Precaution Summary
Safety Information, Continued..
Product safety labels should be inspected and
cleaned periodically to maintain good legibility.
Replace any labels that are no longer legible.
WARNING: This product may
expose you to chemicals including
DEHP, which is known to the State of
California to cause cancer. For more
information, go to www.P65Warnings.

6
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Congratulations on your purchase of the
Speed Demon 5TM Vortex Mixer. This machine
is designed to accommodate single round 5
gallon plastic or metal containers weighing up
to 80 lb. (36.3 kg). It can also accommodate
square quart cans when used in conjunction
with the optional adapter, part no. 9784203. See
section 9, Ordering, for ordering instructions.
Understand your machine's features and
proper operation to take full advantage of its
capabilities.
Read this entire manual completely before
operating the machine. Practice installing and
removing a pail before mixing for the first time.
Keep this manual for future reference.
Always follow all safety instructions!
Unit Size, 5315PB: W26.3 in. (66.7 cm) D 28 in.
(71.1 cm) H36.5 in. (927 cm)
Machine Weight
5315PB: 267 lb. (121 kg)
Maximum Capacity: 80 lb. (36.3 kg)
Sizes Mixed: One gal., Five gal.
Electric Service: 110 V 60 Hz
110 V Units
Machines rated at 110 V, 60 Hz are for use with
a nominal 120 V circuit.
26 1/4"
36 1/2"
28"
2. Introduction
2.1 Application 2.2 Specifications

7
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
This machine was shipped fully assembled.
Before plugging in the machine or attempting to operate it:
1. Open the door and locate the shipping block and rope assembly. Remove the pin as shown by
lifting straight up.
2. Remove the block by sliding outwards. Repeat steps 1 and 2 for the other side
3. Discard or store the shipping blocks and rope assemblies.
4. Set the machine on a stable, level surface and plug it in an appropriately grounded outlet (see
section 1.2, Safety Precaution Summary, for grounding information).
NOTE: If the machine needs to be shipped any time, contact Radia Products to obtain the appropriate
instruction sheet, part no. 1785025 and shipping block assembly, part no. 9784291. See section 9,
Ordering, for ordering information.
Step 1 Step 3Step 2
3. Unpacking & Installation

8
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
• E-Stop (A): Only use to immediately cut the power to the machine
• Circuit Breaker (B): Reset power after cause for circuit trip is xed.
• Digital Display (C): View programming revision and cycle time remaining.
• Two-Minute Cycle (D): Push to set a two-minute cycle, and to increase cycles in two minute
increments.
• Three-Minute Cycle (E): Push to set a three-minute cycle, and to increase cycles in three minute
increments.
• Stop (F): Press to stop a cycle before the preset time expires.
(F)
4. Operation
4.1 Control Panel
(B) (D) (E)
(C)
(A)

9
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Always unplug the power cord before cleaning! DO NOT get the timer, control panel, or wiring
wet.
CLEANING:
Keeping the machine clean is important for reliable operation.
• Colorant or base paint spilled on machine surfaces can be removed using lukewarm water and
mild detergent for water-based/glycol colorants.
• To preserve the appearance of the machine, do not use abrasives to clean machine surfaces.
NOTE: Mixer has been designed and tested for mixing full pails of paint. Mixing partial pails can result
in damage to the mixer.
1. Open the cabinet Door
2. Load the can into the machine for mixing:
• 5 Gallon Pail: Insert the pail into the holder. Slip the bail handle into the clip retainer (A) (See Figure
1).
• 1 Gallon Round Cans: Place the can inside the gallon adapter, A1501. Set the gallon can as
shown with the lid up. (See Figure 2)
• 1 Gallon Square Cans: Place the square can inside the gallon adapter with the lid up. (See Figure
3)
3. Close the cabinet door. The mixer has a safety switch that interrupts operation if the door is open.
4. Select the desired mix time.
If the container handle wasn’t properly secured, press the STOP button on the control panel.
NOTE: If colorant has been added to the paint, be sure to reattach paint can lid tightly (using the
RADIA PRODUCTS Lid Press, Part No. 0-5080).
(A)
Figure 1 Figure 3
Figure 2
4.2 Install a Container
5. Care and Maintenance
5.1 Cleaning

10
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Disconnect the machine from its power source before servicing .
6. Troubleshooting
PROBLEM CAUSE REMEDY
Machine won't operate
Not connected to power source Connect to power source
Building circuit breaker or fuse
blown
Reset breaker or replace fuse
Machine door does not make
contact with limit switch
Re-adjust switch to make contact
wit limit switch screw when door is
closed
Machine circuit breaker tripped
Emergency E-STOP push button
is activated
Contact Radia's Customer Care
Contact Radia's Customer CareFaulty controller
Faulty motor Contact Radia's Customer Care
Contact Radia's Customer Care
Excessive Vibration Can not properly seated
Adjust and level feet
Machine dosen't shut off
at end of mixing cycle Faulty controller
Contact Radia's Customer Care
Machine dosen't shut off
when door is opened
Faulty door limit switch
Contact Radia's Customer Care
Increasing mechincal
noise Bearings worn or damaged
Feet are not Level
Fix or replace pail
Reset can into holder
Turn switch knob 1/4 turn clockwise
to disengage
Reset by pressing circuit breaker
back in
Worn, damaged, or loose drive
belt
Unplug power cord, open mixer door,
and visually inspect the drive belt
Pail Damaged
Faulty door limit switch

11
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
HOT/L2 - BROWN
NEUTRAL/L1 - BLUE
MOTOR 6786030
EMERGENCY
STOP BUTTON
5784827
BROWN WIRE 2X 5784935
BLACK WIRE 5782556
BREAKER, 20 AMP
5785315
WIRE NUT, YELLOW
9780543
DIGITAL DISPLAY TIMER,
HORIZONTAL DISPLAY
5786234
GROUND - GREEN/YELLOW
POWER CORD
5784034
MOTOR HARNESS
5784279
RED
GREEN
RED BLACK/WHITE
BLACK/WHITE
HARNESS, OPERATIONS, DIGITAL DISPLAY - 5315 5786228, SHOWN IN BOLD
BLACK
BLACK WIRE
5782557
WHITE
B1 B2
BLUE
ORANGE
RED
GROUND
BLACK WHITE YELLOW
WIRE NUT, YELLOW 9780543
GN/YEL
SHRINK WRAP
SHRINK WRAP
T1
NEUTRAL
T2
DOOR SWITCH
5783815
WHITE
BLUE
NC NO
COM
7. Wiring Diagrams

12
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
12
11
5
10
9
34
1
2
6
7
8
12
11
5
10
9
34
1
2
6
7
8
ID Description
1 9786816 PLATE, DIGITAL TIMER
2 9781367 Screw Hex Thd Form #8 X .50
3 9786232 SPACER
4 5786234 TIMER, DIGITAL, HORIZONTAL DISPLAY, 120V
5 9783595 Nut, Lock, Nylon 4-40
6 1786198 LABEL, CONTROL, DIGITAL DISPLAY - 5315
7 5785315 Circuit Breaker, 20 Amp, Pop-out
ID Description
85784827 e-stop switch
99787227 GUARD, LIMIT SWITCH
10 5783815 Switch, Limit 1hp
11 9781840 Nut, Keps #8-32
12 9102519 BUSHING,STR.RELIEF
8. Exploded Views
8.1 Electrical Assembly
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

13
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
3
15
6
7
21
20
12
13
14
19
9
18
11
10
5
4
16
17
2
8
1
3
15
6
7
21
20
12
13
14
19
9
18
11
10
5
4
16
17
2
8
1
ID Description
1 9787223 PANEL WELDMENT, RIGHT - 5315
2 9787218 COVER WELDMENT - 5315
3 9787214 PANEL WELDMENT, LEFT - 5315
4 9787216 PANEL, FRONT-5315
5 9787225 DOOR WELDMENT - 5315
6 9787224 PANEL, BACK - 5315
7 9783385 Screw, #10-32 SHWH Tap
8 9784338 Plug, Nylon
9 9781831 Screw, Hex 1_4 X 1
10 9760514 Washer 1_4 SAE .281 ID
11 9780343 Nut 1_4-20 Nylon Lock
ID Description
12 9784361 BUSHING, STEEL
13 9782362 BUSHING, BRONZE
14 9780886 SCREW HEX 3_8-16 X 1.00
15 9106254 Bumper, Foot
16 9784303 HANDLE WELDMENT, DOOR - 5315
17 9784285 SCREW, FLAT HD, 82 DEG, PH #10-32 x .50
18 9781383 NUT, NYLON LOCK #10-32
19 9780789 BUMPER, PAD
20 9781831 Screw, Hex 1_4 X 1
21 9780164 Washer 1_4 LOCK
8.2 Enclosure Assembly
...Exploded Views, Continued
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

14
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
2
11
10
6
1
7
9
3
4
8
5
6
7
2
11
10
6
1
7
9
3
4
8
5
6
7
ID Description
1 6784582 Speed Reducer Kit - 5315
2 6786030 MOTOR, AC, 1 HP, 56C FOOT MOUNT
3 9784259 Plate, Top - Mix Frame
4 9784258 Bracket, Gearbox
5 9161100 Washer, Flat 3_8 USS
6 9780402 Washer 3_8 split lock
ID Description
79780886 SCREW HEX 3_8-16 X 1.00
89780193 Nut, Nylock 3_8-16
99782319 KEY STOCK 3_8 X 3_8 X 4.00
10 9781083 Washer, Flat .507 ID x 2.00 OD x .19 Thk
11 9782154 Screw Hex 1_2 X 1_50
...Exploded Views, Continued
8.3 Drive, Bottom Assembly
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

15
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
1
4
2
3
5
8
6
7
1
4
2
3
5
8
6
7
ID Description
19784228 Gear, Ring
29784261 Retainer, Ring Gear
39784282 SCREW, SOC HD CAP 5_16 -18 X 1.25
46787072 Bearing Housing Assy, Drive Shaft - 5315
59784263 Shaft, Drive - 5315
ID Description
6 9784360 COUNTERWEIGHT - 5315
7 9784299 Screw Hex 3_8-16 x 4.50 Partial Thread
8 9780193 Nut, Nylock 3_8-16
...Exploded Views, Continued
8.4 Drive, Middle Assembly
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

16
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
4
3
1
7
6
5
2
13
12
8
9
10
11
4
3
1
7
6
5
2
13
12
8
9
10
11
ID Description
1 9784230 Arm, Orbit
2 9784348 CAN DRIVE WELDMENT 5315
3 9784229 Gear, Pinion
4 9782316 Bushing, Trantorque
5 9781831 Screw, Hex 1_4 X 1
6 9780164 Washer 1_4 LOCK
7 9760514 Washer 1_4 SAE .281 ID
ID Description
8 9784264 Holder, Can - 5315
9 9784327 Plate, Round - 5315
10 6785232 Ring, Rubber
11 9782904 Screw Button 5_16-18 x .75
12 9784268 Retainer Bar, Bail
13 9781383 NUT, NYLON LOCK #10-32
8.5 Drive, Can Holder Assembly
...Exploded Views, Continued
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

17
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
16
15
1
12
14
811
10
2
7
9
13
3
654
16
15
1
12
14
811
10
2
7
9
13
3
654
ID Description
1 9784249 Base Weldment - 5315
2 9784250 FRAME, SUSPENDED - 5315
3 9784252 Spring, Extension
4 9781543 Screw Hex 3_8 X 2_25
5 9161100 Washer, Flat 3_8 USS
6 9784357 BEARING, SLEEVE
7 9784349 Cam, Spring Mount - 5315
8 9780193 Nut, Nylock 3_8-16
9 9784358 Screw Hex 5_16-18 X .50
ID Description
10 9784255 Damper, Disc
11 6784738 ISOLATOR ASSEMBLY - 5315
12 9780182 Nut, Nylock 5_16-18
13 9784326 Bumper, Single Round Stud
14 9780343 Nut 1_4-20 Nylon Lock
15 9782044 Foot, Floor Stand
16 9780886 SCREW HEX 3_8-16 X 1.00
8.5 Frame Assembly
...Exploded Views, Continued
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

18
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
HOW TO ORDER REPLACEMENT PARTS
Replacement parts can be ordered from Radia by telephone, fax, or email:
If you need help in determining the proper part(s) to order, please call Customer Care.
at 1-800-221-1083. Always indicate the Model and Serial numbers of the machine when
ordering replacement parts.
GENERAL PARTS REPLACEMENT POLICIES
While your machine is under warranty, do not attempt on-site repair or parts replacement
without first contacting RADIA. (to protect your warranty). After the warranty expires,
replacement parts and recommendations for on-site servicing are available from RADIA.
Please contact Customer Care for assistance.
RESTOCKING FEE
A restocking fee will be charged on all unused parts which are returned.
Replacment Parts
9. Ordering
RADIA
800-221-1083
763-533-2969
763-533-0015 (FAX)
[email protected]
For instructional "How To" videos please visit:
www.radiaproducts.com
??

19
Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Equipment Covered Under This Warranty
Warranty
Models 5315-PB
10. Warranty
Radia warrants equipment manufactured by it and bearing its name to be free from defects in
material and workmanship.
EXCEPT FOR THE WARRANTY SET FORTH HEREIN, RADIA MAKES NO WARRANTY WHATSOEVER
WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY (a) WARRANTY OF MERCHANTABILITY; (b)
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE; OR (c) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW,
COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE.
This warranty applies only when the equipment is installed, operated and maintained in
accordance with written Radia instructions as appearing in the owners’ manuals.
This warranty does not cover, and Radia shall not be liable for, any malfunction, damage, or
wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper
maintenance, negligence, accident, tampering or substitution of non-Radia component parts,
modification or use for non-intended purposes. Nor shall Radia be liable for malfunction, damage or
wear caused by the incompatibility of Radia equipment with structures, accessories, equipment, or
materials not supplied by Radia.
Subject to the limitations set forth above, Radia shall (i) repair or replace the equipment (or the
defective part) or (ii) credit or refund the price of such equipment. Costs of labor and transportation
for service of machines under this warranty will also be covered during the warranty period if Radia
elects to repair or replace the equipment. Normal ground freight will be covered for replacement
parts sent within the warranty period. For customers outside of the US and Canada, the warranty is
for parts only. Ground or common carrier ground freight will be covered for the return of defective
items only. In no case shall Radia's liability exceed the amount of the purchase price.
*All warranty repairs must be executed by a Radia Authorized Service Center or warranty will be
voided.
THE REMEDIES SET FORTH HEREIN ARE PURCHASER’S SOLE AND EXCLUSIVE REMEDY and RADIA’S
ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET FORTH HEREIN.
Please contact your Radia Relationship Manager at 800-221-1083 for specific questions regarding
specific questions regarding warranty terms.

Owner’s Manual: 5315
1784242 Rev X
ECO 18-0034
July 2018
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
U.S. Telephone:
International Telephone:
Fax:
E-mail:
www.radiaproducts.com
For sales or service, please contact
RADIA
Attn: Customer Service Department
14900 21st Ave N
Plymouth, Mn 55447
USA
800.221.1083
763.533.2969
763.533.0015
[e-mail]
For instructional "How To" videos please visit:
www.radiaproducts.com
??