radiance RHW-450 Specifications

OWNER & OPERATOR
INSTRUCTION MANUAL
For service contact:
German Knife Inc.
1-800-500-3519
www.turboairinc.com
Model No. RHW-450
FOOD WRAPPER
www.turboairinc.com

TABLE OF CONTENTS
INSTALLATION
MAINTENANCE
SPECIFICATIONS
WARRANTY INFORMATION
3-4
5-6
7
8
PAGE
German Knife, Inc.
4184 E. Conant St., Long Beach, CA 90808
Phone: [phone]
Fax: [phone]
www.turboairinc.com
The equipment is inspected & crated carefully by skilled personnel before leaving factory. The transportation company
assumes full responsibility for safe delivery upon acceptance of this equipment if shipment arrives damaged;
1. VISIBLE LOSS OR DAMAGE: Note on freight bill or express delivery and signed by person making delivery.
2. FILE CLAIM FOR DAMAGES IMMEDIATELY: regardless of extent of damages.
3. CONCEALED LOSS OR DAMAGES: If damages are noticed after unpacking, notify Transportation Company
immediately and file “Concealed Damage” claim with them. This should be done within fifteen (15) days from date
delivery is made to you. Return container for inspection.
SHIPPING DAMAGE CLAIM PROCEDURE
2

INSTALLATION
3
UNPACKING:
1. Remove appliance from container.
2. Remove all protective packaging material.
3. Retain container and packaging material until the appliance is operated and found
in good condition.
4. Check appliance for any shipping damage. If appliance shows any external or internal
damages, promptly inform dealer/distributor where you bought your appliance.
GENERAL SAFETY INSTRUCTIONS:
A
ccidents are always tragic especially because so many of them could have been prevented with
little care and judgment. There are some basic good practices; we hope you will follow for safe
use of the equipment.
INSTALLATION:
1. Always clean equipment interior and exterior thoroughly before using.
2. Keep away from water or moisture.
3. Check rating label for your model designation & electrical rating.
4. Set film on back roller and install the film as shown below.
5. Set earth wire for preventing electric shock.
6. Adjust the tension bolt in order to have elasticity in pulling of the film.
NOTE: Installation and repair should be done by a qualified service person. Qualified service person;
who have read these instructions and is familiar with the operation and functions of the equipment.

INSTALLATION
4
FILM OUTSIDE

MAINTENANCE
5
OPERATING INSTRUCTIONS:
1. Set the tray containing goods or materials on the work table.
2. Pull the wrap film from the gap of work table rollers and cover the tray or material with film.
3. Draw down the wrapped tray to the heat plate. At this point, the heat cutter will cut the film by
heat automatically.
4. Put down the tray on the plate and press the tray lightly several times.
5. Check the wrapped tray.
GENERAL INSTRUCTIONS:
1. Fuse – This machine uses a 2A fuse on the name plate. 2A simply means 2 Amp fuse.
2. Work Table – The goods for wrapping must be set on the work table.
ALWAYS USE THE TRAY WHEN YOU WRAP GOODS.
DO NOT WRAP ANY TRAY THAT CONTAINS WATER.
3. Tension Bolt – This tension bolt is to have elasticity in pulling of the film.
4. Control Board – This board controls the voltage that is given by volume level.
DO NOT USE TRAY IF IT CONTAINS WATER OR OIL
DO NOT TOUCH THE CUTTER AND COVER BY HAND
USE 2A FUSE ONLY FOR THIS MACHINE !
REPLACING THE HEAT CUTTER:
1. Unscrew the cutter cover standing screw and take the cover away from the cutter.
2. Release the cutter wire holding screw.
3. Pull the cutter wire from the front panel wire.
4. Release the new cutter and tighten the screws.

MAINTENANCE
6
FUNCTION OF EACH PART:
1. Heat Cutter – When the film is pulled down from the tray, the heat cutter located underneath
the heat cutter guard cuts the film using electric heat.
2. Heat Cutter Guard – Heat cutter guard protects the operator from the cutter which produces
radiation heat of up to 113°C (235°F).
3. Heat Plate – After wrapping the tray with film, cut the film with the cutter, then lay the tray on
the heat plate so that it can seal the tray with the melted film.
4. Heat Cutter Switch – Turns on the heat cutter.
5. Heat Plate Switch – Turns on the heat plate.
6. Heat Plate Lamp – When you turn the plate switch on, the lamp turns on and lamp can be
adjusted bright or dark.
7. Volume Switch – This switch control the voltage which is supplied to the machine from
25V-120V.
Heat Cutter Heat Plate Heat Plate Volume Switch
Fuse Holder Heat Cutter Switch Heat Plate Lamp Power Cord
Side Panel Work Table Roller Heat Cutter Cover
1
4
8 9 10 11
5 6 7
2 3

SPECIFICATIONS & TROUBLESHOOTING GUIDE
7
SPECIFICATIONS
TROUBLESHOOTING GUIDE
5⁄8
7⁄8
1⁄2
3⁄4
Temperature of Heat Plate
Temperature of Heat Cutter
Voltage
Wrapping Length (inch)
Power Consumption
Ext. Length Overall (inch)
Ext. Depth Overall (inch)
Ext. Height Overall (inch)
110°F
125°F
AC 115V 60Hz 1Phase
17
175W
18
23
3
SYMPTOM POSSIBLE CAUSE POSSIBLE SOLUTION
Heat plate lamp
does not turn on.
(Does not make seal)
Heat cutter
does not heat up.
(Does not cut film)
Controller
does not work.
Bad power cord or socket
Heat plate wire disconnected
Bad controller
Bad lamp & lamp connector
Fuse gone out
Heat cutter not set in place
Bad lamp
Change heat cutter
Ask for service
Ask for service
Ask for service
Overheating
Bad controller
Check & replace power cord and/or sock
Change heat plate
Ask for service
Ask for service
Change heat cutter

LIMITED WARRANTY
WARRANTY CLAIM:
PRODUCTS UNDER WARRANTY:
WHAT IS NOT COVERED BY THIS WARRANTY:
One Year Warranty:
Radiance Medium Duty Microwaves- ER/MR series (TMW-1100ER, TMW-1100MR)
Radiance Ranges & Countertop cooking series
(All TAR-, TARG-, TAHP-, TARB-, TAMG-, TATG-, TASP-, TAWR-)
Radiance Cheesemelters, Salamanders, Steam Tables, Food Wrappers, and Food Warmers
(All TACM-, TASM-, RST-, RHW-, RFW-)
German Knife Light Duty Slicer- LD series (GS-10LD, GS-12LD)
Two Year Warranty:
German Knife Heavy Duty Meat Slicer- Automatic & Manual (GS-12A, GS-12M, GS-13A, GS-13M)
German Knife Meat Grinder (All GG-)
German Knife Band Saw (All GBS-)
Three Year Warranty:
Radiance Heavy Duty Microwaves- HD Series (TMW-1200HD, TMW-1800HD)
Any part covered under this warranty that is found by German Knife / Radiance to have been defective within the
above time period is limited tothe repair or replacement, including labor charges, of defective parts or assemblies.
The labor charges shall include standard straight time labor charges only and reasonable travel time as determined
by German Knife / Radiance.
German Knife / Radiance warrants that the equipment, as supplied from the factory tothe end-user, is free from
defects in materials and workmanship. Should any part be found defective resulting from normal use within the defined
warranty period, German Knife / Radiance will gladly dispatch an authorized service agency to repair and/or replace
necessary parts under the following conditions.
Repairs under this warranty are to be performed by aGerman Knife / Radiance authorized service agency only.
German Knife / Radiance will not be responsible for service parts and labor charges performed by non-authorized
service companies. All claims should include the model number, serial number, proof of purchase, date of installation,
and all pertinent information supporting the alleged defect.
German Knife / Radiance’s sole obligation under this warranty is limited to either repair or replacement of parts,
subject tothe additional limitations below. This warranty neither assumes nor authorizes any person to assume
obligations other than those expressly covered by this warranty.
Equipment failure resulting from improper installation will not be honored under warranty. Examples are
wrong utility connection and improper utility supply problems.
Equipment that has not been maintained accordingly. Examples are calibration of controls, adjustment to
pilots and burners, and damage from improper cleaning.
Equipment that has not been used in an appropriate manner, alteration, neglect, abuse, misuse, accident,
damage during transit or installation, fire, food, acts of God.
Warranty is not transferrable and only applies in favor of the original purchaser.
Equipment failure resulting from electrical power failure, use of extension cords, low voltage, and voltage
drops tothe unit.
These warranties are exclusive and in lieu of all other warranties, including implied warranty and merchantability or
fitness for a particular purpose. No consequential damages. German Knife / Radiance is not responsible for economic
loss, profit loss or special, indirect, or consequential damages. There are no warranties which extend beyond the
description on the face hereof.
Outside the U.S., this warranty does not apply to, and German Knife / Radiance is not responsible for, any warranty
claims made on productssold or used outside the continent of the United States.