Radiant Communications DL221 Series User manual

SERIES DL221
10/100 ETHERNET TRANSCEIVER
USER MANUAL
Radiant Communications Corporation
P.O. BOX 867 •5001 Hadley Road •South Plainfield, NJ 07080
800.969.3427 •Fax [phone]
E-mail: [email protected]om •www.rccfiber.com
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 1

ETHERNET 10/100 TRANSCEIVER SERIES DL221/DL221A
REV B4.3
FOR AC INPUT
FRONT PANEL INDICATORS –
POWER – ON WHEN UNIT HAS POWER
100M – ON WHEN TWISTED PAIR IS WORKING AT 100Mbs
OFF WHEN TWISTED PAIR IS WORKING AT 10Mbs
LINK FX – ON WHEN FIBER OPTIC LINK PRESENT
TP – ON WHEN TWISTED PAIR LINK PRESENT
FDX – FULL DUPLEX. BOTH ARE LIT WHEN FIBER OPTIC LINK
AND TWISTED PAIR ARE OPERATING AT FULL DUPLEX.
NOTE- FIBER OPTIC LINK IS ALWAYS OPERATING AT FULL DUPLEX.
POWER • • 100M
LINK FX • • TP
FDX • - •
10/100 BASE – TX
100BASE TX PORT
RJ-45 CONNECTOR
HALF/FULL DUPLEX SUPPORT VIA AUTO-NEGOTIATION OR MANUAL
100m OVER UTP/STP 100ohm CAT.5 CABLE
X II
MDI-II/MDI-X SELECTION
X – CROSS OVER CABLE
II – STRAIGHT CABLE
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 2

MODE SETUP
NOTE - SWITCH 4 MUST BE IN THE ON/UP POSITION FOR UNIT TO
OPERATE. AFTER CONFIGURATION OF UNIT POWER MUST BE RESET.
THIS CAN BE DONE BY REMOVING POWER TO UNIT OR TOGGLE SWITCH 4
DOWN THEN UP.
SETTINGS-
AUTO-NEGOTIATION - SW 1, SW 2, SW 3 DOWN/OFF
10M HALF DUPLEX - SW 1 UP/ON, SW 2, SW 3 DOWN/OFF
10M FULL DUPLEX - SW 1 UP/ON, SW 2 DOWN/OFF, SW 3 UP/ON
100M HALF DUPLEX - SW 1 UP/ON, SW 2 UP/ON, SW 3 DOWN/OFF
100M FULL DUPLEX - SW 1 UP/ON, SW 2 UP/ON, SW 3 UP/ON
TROUBLESHOOTING
POWER LED NOT LIT - CHECK POWER SUPPLY CABLE TO MAIN POWER
SUPPLY. CHECK AC INPUT SOURCE. CHECK SW 4 – MUST BE UP/ON
POSITION.
LINK FX LED NOT LIT – CHECK LIGHT LEVEL IN AND OUT OF UNIT. REFER
TO THE SPEC. LABEL FOR PROPER LEVEL.
TP LED NOT LIT - CHECK SETTING FOR STRAIGHT / X-OVER CABLE. RESET
POWER.
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 3

FOR 5VDC INPUT
FRONT PANEL INDICATORS –
RWR – ON WHEN UNIT HAS POWER
R – ON WHEN TWISTED PAIR IS WORKING AT 100Mbs
OFF WHEN TWISTED PAIR IS WORKING AT 10Mbs
L – ON WHEN FIBER OPTIC LINK PRESENT
A – ON WHEN TWISTED PAIR LINK PRESENT
FX TX FDX – FULL DUPLEX. LIT WHEN FIBER OPTIC LINK
AND TWISTED PAIR ARE OPERATING AT FULL DUPLEX.
NOTE- FIBER OPTIC LINK IS ALWAYS OPERATING AT FULL DUPLEX.
RWR R
• •
• • L/A
• • FDX
FX TX
10/100 BASE – TX
100BASE TX PORT
RJ-45 CONNECTOR
HALF/FULL DUPLEX SUPPORT VIA AUTO-NEGOTIATION OR MANUAL
100m OVER UTP/STP 100ohm CAT.5 CABLE
NODE HUB MDI-II/MDI-X SELECTION
NODE - CROSS OVER CABLE
HUB - STRAIGHT CABLE
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 4

SETTINGS-
AUTO-NEGOTIATION - SW 1, SW 2, SW 3 DOWN/OFF
10M HALF DUPLEX - SW 1 UP/ON, SW 2, SW 3 DOWN/OFF
10M FULL DUPLEX - SW 1 UP/ON, SW 2 DOWN/OFF, SW 3 UP/ON
100M HALF DUPLEX - SW 1 UP/ON, SW 2 UP/ON, SW 3 DOWN/OFF
100M FULL DUPLEX - SW 1 UP/ON, SW 2 UP/ON, SW 3 UP/ON
NOTE- AFTER CONFIGURATION OF UNIT POWER MUST BE RECYCLED.
TROUBLESHOOTING
RWR LED NOT LIT - CHECK POWER SUPPLY. ENSURE OUTPUT 5VDC.
L LED NOT LIT - CHECK LIGHT LEVEL IN AND OUT OF UNIT. REFER TO THE
SPEC. LABEL FOR PROPER LEVEL.
A LED NOT LIT – CHECK TWISTED PAIR CONNECTIONS.
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 5

SPECIFICATIONS
Standard Compliance:
IEEE802.3u, 100BaseTx, 100BaseFx, 10BaseT
100BaseTx Port:
RJ-45 connector
Half/full duplex support via auto-negotiation or manual
100m over UTP/STP 100 ohm cat.5 cable
Auto-polarity correction
MDI-II/MDI-X selection
10BaseT (switch selected)
100BaseFx Port:
1300nm SC connectors. Optional Single Fiber (DL221A)
Distance:
> 100 km (DL221/SMSP)
Full/half duplex switch selected
Diagnostics:
Per Channel:
Full duplex, Link, Activity - 100BaseFx side
Per System:
Power (dual, if redundant PS present)
Controls:
Fiber side:
FDX/HDX
Copper side:
10/100 Mbps, FDX/HDX, Auto sensing disable/enable
Environmental/Physical:
Power supply:
100/240 VAC.50/60 Hz
5VDC wall
Power consumption:
5 W max.
Operating temperature:
0˚-45˚C (32˚-113˚F)
Storage temperature:
-30˚- 65˚C (22˚- 149˚F)
Humidity:
10-90% non-condensing
NOTE - Specifications subject to change without prior notice.
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 6

PART NUMBER DESCRIPTION ATTEN. MAX. DISTANCE
DL221-XYZ Transceiver,
Multimode, 2 fibers 9dB 6km
DL221/SM-XYZ Transceiver,
Singlemode, 2 fibers 9dB 25km
DL221/SMHP-XYZ Transceiver,
Singlemode , 2 fibers 18dB 50km
DL221/SMSP-XYZ Transceiver,
Singlemode, 2 fibers 28db 80km
DL221/SMUP-XY5 Transceiver,
Singlemode, 2 fibers 28db 110km
DL221A-XYZ Transceiver,
Multimode, 1 fiber 6db 2km
DL221A/SM-XYZ Transceiver,
Singlemode, 1 fiber 9db 25km
DL221A/SM2-XA3 Transceiver,
Singlemode, 1 fiber 18db 50km
DL221A/SMHP-XYZ Transceiver,
Singlemode, 1 fiber 18db 50km
DL221A/SMSP-XYZ Transceiver,
Singlemode, 1 fiber 28db 80km
Note:
Specify X- packaging of the unit: U-1U rack mount, M-modular, R-card cage rack mount
Specify Y- connector type: A-SC/APC, E-SC, B-FC, Z-FC/APC, D- ST
Specify Z- wavelength: Multimode 8-850nm, 2-1300nm Singlemode 3-1310nm, 5- 1550nm
Add -M for SNMP management
Add -48 for 48VDC power
For higher optical budgets and distances, CWDM and DWDM systems, contact factory
Note:
 Specify X—packaging of the unit: U—1U rack mount, M—modular (standalone), R—car
 Specify Y—connector type: A—SC/APC, E—SC, B—FC, Z—FC/APC, D—ST
 Add –SNMP for SNMP management
 Add –48 for 48VDC power
 For higher optical budgets and distances, CWDM and DWDM systems, contact factory
Radiant Communications Corporation
P.O. BOX 867 •5001 Hadley Road •South Plainfield, NJ 07080
800.969.3428 •Fax [phone]
E-mail: [email protected]om •www.rccfiber.com
RADIANT COMMUNICATIONS CORP. DL221 REV B4.3 7/04 7