Radio Shack Mobile CB Instruction Manual

The FCC Wants You to Know ........................................................................................... 2
Installation ......................................................................................................................... 2
Attaching the Microphone Holder ............................................................................... 2
Mounting the CB ........................................................................................................ 2
Connecting the Microphone ....................................................................................... 3
Connecting an Antenna ............................................................................................. 3
Connecting Vehicle Battery Power ............................................................................. 4
Connecting an External Speaker ............................................................................... 4
Using the CB As a Base Station ....................................................................................... 4
Operation .......................................................................................................................... 5
Receiving Transmissions and Setting Squelch .......................................................... 5
Changing Channels Using the Controls on the Microphone ...................................... 6
Dual Watch and Memory Setting ............................................................................... 6
Transmitting ............................................................................................................... 6
Listening to the Weather Band ................................................................................... 6
Digital Weather Alert .................................................................................................. 6
Weather Channel Frequencies .................................................................................. 7
Using Compass .......................................................................................................... 7
Calibrating the Electronic Compass ........................................................................... 8
Transmission Courtesy .............................................................................................. 8
Maximum Range ........................................................................................................ 8
Reducing Noise ......................................................................................................... 8
Using Common 10-Codes .......................................................................................... 9
Troubleshooting .............................................................................................................. 10
Care ......................................................................................................................... 10
Replacing the Fuse .................................................................................................. 10
Specifications .................................................................................................................. 11

OWNER’S MANUAL — Please read before using this equipment.
©2001 RadioShack Corporation. All Rights Reserved.
RadioShack and RadioShack.com are trademarks
used by RadioShack Corporation.
Mobile CB with Compass, Dual Watch and Digital
Weather Alert
Your RadioShack 40-Channel Mobile CB
Radio provides two-way communications on
the citizen’s radio band and lets you tune to
local and national weather service broad-
casts. You can also connect optional equip-
ment to your CB such as external speakers,
or a DC power supply and base antenna to
set up a base station in your home. The built-
in 40-channel PLL (phase-locked loop) fre-
quency synthesizer uses a precise frequency
reference crystal for reliable and exact tun-
ing.
Ideal for recreational, business, or emergen-
cy use, your CB has these features:
Electronic Compass — provides accurate
heading information.
Dual Watch — checks one channel while re-
ceiving another channel so you do not miss
important transmissions. Dual Watch de-
faults to channel 9 (emergency call channel).
NOAA (National Oceanic and Atmospher-
ic Administration) 7-Channel WX Band
Receiver — lets you tune to seven national
weather service frequencies which provide
local weather conditions and forecasts.
WX Channel Autoscan — In CB mode,
when a weather station carrier is lost, the CB
automatically scans weather channels so it
can detect a weather alert signal transmitted
with a weather signal.
WX/Signal Indicator — shows the CB is
ready to receive and indicates the reception
of a weather alert.
Digital Weather Alert — uses Specific Area
Message Encoding (SAME) digital informa-
tion to determine and display the level of
weather events (does not limit alerts to a
specific area).
ACE (Audio Clarity Enhancer) — sup-
presses noise levels while leaving the signal
intact during reception. It enhances the
transmission and provides a significant re-
duction in transmission and reception noise.
RF Gain Control — prevents overloading
due to strong RF signals.
Convenient On-Microphone Channel Up/
Down Controls — let you quickly scan the
band for communications.
Universal Mounting Bracket — lets you
mount your CB securely in your vehicle.
Specialized Squelch Circuit — compen-
sates for fading signals and eliminates signal
chopping during reception.
Maximum Allowable Legal Power Output
— gives you the greatest available range.
TX Indicator — lights to show when the ra-
dio is transmitting.
Digital Channel Display — makes the
channel number easy to see.
External Speaker Jack — lets you connect
your CB to an external speaker.
Screw-On Mic Connector — ensures a se-
cure microphone connection.
To use this CB, you need a mobile or base
station antenna. Your local RadioShack
store has a wide variety of antennas. For
more information, see “Connecting an Anten-
na” on Page 3.

2
THE FCC WANTS YOU TO
KNOW
The Federal Communications Commission
(FCC) does not require you to have a license
to operate this CB. However, the FCC does
require that you read and know Part 95 of
FCC Rules
. These rules apply to the opera-
tion of a Class D CB. We have provided a
copy of these regulations with your CB.
Warning: Do not open your CB to make any
internal adjustments. Any internal adjustments
can be made only by an authorized service
technician.
Unauthorized internal adjustments and/or
modifications can lead to illegal operation as
defined by Part 95 of
FCC rules
. Such illegal
operation can lead to very serious conse-
quences.
Your CB might cause TV or radio interference
even when it is operating properly. To deter-
mine whether your CB is causing the interfer-
ence, turn off your CB. If the interference goes
away, your CB is causing it. Try to eliminate
the interference by either moving your CB
away from the receiver or contacting your lo-
cal RadioShack store for help. If you cannot
eliminate the interference, the FCC requires
that you stop using your CB.
If you cannot eliminate the interference, con-
tact your local RadioShack store for help.
INSTALLATION
Attaching the Microphone Holder
You can connect the microphone holder to ei-
ther side of the CB or to another location in
your vehicle. To attach the holder to either
side of the CB, horizontally or vertically, se-
cure it using the supplied small screws and
lock washers.
To attach the holder to another location in the
vehicle, such as the dashboard, follow these
steps.
1. Using the holder as a template, mark the
positions for the mounting screw holes at
the desired location.
2. At each marked position, drill a small
starter hole for the supplied mounting
screws.
Caution:
Be careful not to drill into any-
thing behind the mounting surface.
3. Attach the holder at the mounting location
using the supplied small screws and lock
washers.
Mounting the CB
The most common mounting location for this
CB is under a vehicle’s dashboard. However,
if you use the CB as a base station, you can
place it on a desk, shelf, or table (see “Using
the CB As a Base Station” on Page 4).
If you are mounting the CB in a vehicle,
choose a location where:
• you can easily reach the CB.
• wires and cables are clear of the vehicle’s
pedals or other moving parts.
• the CB is not directly in front of heating
vents.

3
• the magnetic fields caused by the vehi-
cle’s wiring do not affect the CB. (See
“Calibrating the Electronic Compass” on
Page 8.)
• all wires and cables can reach their con-
nection points.
Warning: If you use the CB in a vehicle,
mount it securely to avoid damage to the CB
or vehicle or injury to anyone in the vehicle
during sudden starts or stops.
Follow these steps to mount the CB using the
supplied hardware.
1. Using the mounting bracket as a tem-
plate, mark the positions for the screw
holes on the mounting surface.
2. In each marked position, drill a small
starter hole for the supplied mounting
screws.
Caution: Be careful not to drill into
objects behind the mounting surface.
3. Attach the mounting bracket to the
mounting surface with the supplied
screws and lock washers.
4. Attach the CB to the mounting bracket
using the supplied rubber washers and
mounting knobs.
Note: To use the radio’s compass mode cor-
rectly, you have to install the CB horizontally.
Connecting the Microphone
1. Align the slot on the top of the micro-
phone’s plug with the ridge inside the
microphone jack. Then fully insert the
plug into the jack.
2. Turn the plug’s locking nut clockwise to
tighten it.
3. Slide the microphone onto the micro-
phone holder.
To disconnect the microphone from the CB,
unscrew the locking nut then pull out the plug.
Caution: Never pull on the microphone’s ca-
ble.
Connecting an Antenna
There are many different types of CB antenna
for mobile CBs. Each antenna type has its
own benefits, so choose the one that best
meets your needs. Your local RadioShack
store sells a wide variety of antennas.
For the best performance you should mount
the antenna:
• as high as possible on the vehicle

4
• as far as possible from an electrical noise
source
• vertically
Note: If you are using this CB as a base sta-
tion, see “Using the CB As a Base Station” .
Once you choose an antenna, follow its
mounting instructions. Then route the cable
(not supplied) to the CB and connect the cable
to the ANTENNA jack on the back of the CB.
Cautions:
• Avoid routing the cable next to sharp
edges or moving parts, which might dam-
age the cable.
• Do not run the cable next to power cables
or other radio antenna cables.
• Do not run the cable through the engine
compartment or other areas that produce
extreme heat.
For maximum range, adjust the antenna’s
Standing Wave Ratio (SWR) using an SWR
meter (not supplied).
Follow the instructions supplied with the SWR
meter and antenna to adjust your antenna’s
SWR to the lowest possible value. SWR val-
ues of 2.0:1 are generally acceptable, with
readings of 1.5:1 or lower being more desir-
able.
Connecting Vehicle Battery Power
Follow these steps to connect the CB to vehi-
cle battery power.
1. Connect the red wire (with the in-line fuse
holder) on the back of the CB to a termi-
nal in your vehicle’s fuse box that has
power only when the ignition is in the
ACC (accessory) or ON position.
2. Connect the black ground wire to a metal
part of the vehicle’s frame (chassis
ground).
Caution: Do not connect the black wire to a
non metallic (plastic) part, or to any part insu-
lated from the vehicle’s chassis by a non-me-
tallic part.
Connecting an External Speaker
You can connect an optional external speaker
to the CB. Only use an 8-ohm speaker with a
1/8-inch (3.5-mm) plug. Insert the speaker’s
plug into the CB’s EXT jack. Your local Ra-
dioShack store carries a wide selection of
suitable speakers.
USING THE CB AS A BASE
STATION
Although this CB is designed mainly for mo-
bile use, you can also use it as a base station
with an AC power source. For base station in-
stallation, you need these items (not sup-
plied).
• a 13.8-volt DC power supply that supplies
at least 1.6 amps
Caution: Most 13.8-volt DC power sup-
plies plug into a standard AC outlet to
produce DC power. Before connecting
your CB to a 13.8-volt DC power supply,
read and follow the instructions included
with the power supply.
• base station antenna
• coaxial antenna cable and connectors
Note: Your local RadioShack store carries a
wide selection of base station antennas, coax-
ial antenna cables, and connectors. In addi-

5
tion, you can choose from a selection of
suitable base station power supplies.
Follow these steps to install the CB as a base
station.
1. Mount the base station antenna as
described in its owner’s manual.
Warning: Use extreme caution when you
install or remove a base station CB
antenna. If the antenna starts to fall, let it
go. It could contact overhead power lines.
If the antenna touches a power line, con-
tact with the antenna, mast, cable, or guy
wires can cause electrocution and death.
Call the power company to remove the
antenna. DO NOT attempt to do so your-
self.
2. Connect the antenna to the ANTENNA
jack on the back of the CB.
3. Connect the CB’s black power wire to the
negative (–) terminal on the DC power
supply.
4. Connect the CB’s red wire (with the in-
line fuse) to the positive (+) terminal on
the DC power supply.
5. Connect the DC power supply to a stan-
dard AC outlet.
OPERATION
Before you use your CB, you should know
how to use it effectively and courteously.
“Transmission Courtesy” on Page 8 contains
information that will help you get more enjoy-
ment from your CB.
Caution: Do not attempt to use your CB with-
out first connecting it to an antenna.
Receiving Transmissions and Set-
ting Squelch
1. Set WX/CB/CMP to CB.
2. Turn SQUELCH fully counterclockwise.
3. Turn RF GAIN fully clockwise.
4. Turn on the CB by turning OFF/VOLUME
clockwise. The display lights and the
channel appears.
Note: The CB sounds an alert if it detects
a weather alert signal (see “Digital
Weather Alert” on Page 6).
5. Rotate VOLUME clockwise until you hear
a hissing sound.
6. Slowly turn SQUELCH clockwise until the
hissing sound stops.
Note: To receive very weak signals, turn
SQUELCH counterclockwise. You hear
noise between transmissions, but you
can also hear weak transmissions (those
not strong enough to break through a
higher squelch setting). If the CB picks up
unwanted, weak transmissions, turn
SQUELCH clockwise to reduce the CB’s
sensitivity to these signals.
7. Turn RF GAIN counterclockwise to
decrease the incoming signal strength
and prevent overloading. Or, turn it clock-
wise to receive the maximum possible
signal.
8. Rotate
CHANNEL to select a channel.
9. Adjust VOLUME to a comfortable listening
level.
External Antenna
CB
DC Power Source

6
Note: To improve communication quality,
press ACE/ALERT OFF. The ACE indicator
lights. See “Reducing Noise” on Page 8.
Notes:
• The ACE circuit does not operate when
you select WX.
• You cannot turn on the ACE circuit while
holding down the talk button.
To turn off the CB, turn OFF/VOLUME counter-
clockwise until it clicks.
Changing Channels Using the
Controls on the Microphone
To tune to the next higher or lower channel,
press UP or DOWN on the microphone.
To quickly change channels in either direction,
hold down UP or DOWN until you reach the de-
sired channel.
To prevent accidentally changing the channel
with UP or DOWN, press LOCK. Press LOCK
again to restore the UP or DOWN operation.
Dual Watch and Memory Setting
You can set the CB to check a sub channel
(Channel 9 is preset) while receiving the main
channel. If the CB finds a signal on the sub
channel, it automatically switches to it.
To use dual watch, select the main channel,
then press DUAL/MEM. Press DUAL/MEM
again to turn off dual watch.
To change the sub channel from Channel 9 to
another channel:
1. Select the desired channel for sub chan-
nel.
2. Press and hold DUAL/MEM for about 2
seconds.
3. Select the main channel and press DUAL/
MEM.
Note: Using the microphone to either transmit
or change channels up and down will turn off
dual watch.
Transmitting
Note: We recommend you try receiving trans-
missions before you transmit.
1. To transmit, press the talk button on the
side of the microphone. Hold the micro-
phone about 2 or 3 inches from your
mouth and speak in a normal tone. The
TX indicator lights.
2. When you finish transmitting, release the
talk button. The TX indicator turns off.
3. To turn off the CB, turn OFF/VOLUME
counterclockwise until it clicks.
Listening to the Weather Band
The National Oceanic and Atmospheric Ad-
ministration (NOAA) broadcasts local fore-
cast and regional weather information on one
or more of seven channels in the US. All sev-
en frequencies are preprogrammed in this CB.
(See “Weather Channel Frequencies” on
Page 7.)
To select a weather broadcast, set WX/CB/
CMP to WX, and turn CHANNEL to select one
of the frequencies. Set WX/CB/CMP to CB to
return to normal CB operation. The CB also
detects severe weather alert signals in CB
mode.
Note: The microphone’s talk button does not
work when WX/CB/CMP is set to WX.
Digital Weather Alert
When your local weather station broadcasts a
severe weather alert signal, the radio sounds
an alert tone and the radio’s SAME alert indi-
cator lights according to the emergency level
encoded in the signal.

7
To turn the weather alert off, press ACE/
ALERT OFF.
Notes:
• Because of atmospheric conditions, you
might encounter times when the signal
your radio receives does not contain
information relevant to the emergency
level of the alert. This is normal.
• The CB sounds an alert regardless of the
channel setting.
• The CB does not sound an alert while you
are transmitting.
• The weather alert indications remain on
the display until you press ACE/ALERT
OFF.
• If the carrier of the current weather chan-
nel is lost, the WX/SIGNAL indicator
flashes. (In CB mode, the CB automati-
cally scans weather channels so it can
detect a weather alert signal. While the
CB scans weather channels, the WX/
SIGNAL indicator flashes until the CB
receives a weather station signal.)
• In the CB mode, the display automatically
changes from the CB channel number to
the weather alert indication when the CB
receives a SAME alert signal. You can
hear your local forecast and regional
weather information immediately. Press
ACE/ALERT OFF or the PTT (Press To
Talk) button on the microphone to return
to the CB channel number.
Caution: If you are in a rural or fringe area,
your radio might be triggered by an alert
broadcast for one area, but not for another ar-
ea.
To verify actual reception, your radio must re-
ceive a test or emergency alert broadcast. In
the US, the National Weather Service (NWS)
broadcasts a test alert every week on
Wednesday between 11 am and 1 pm. For the
specific test schedule in your area, contact
your local NOAA or NWS office, usually listed
in the telephone directory under “US Govern-
ment, Department of Commerce.”
Weather Channel Frequencies
Your CB is preprogrammed with the follow-
ing US weather service channel FM frequen-
cies:
Using Compass
Your CB’s electronic compass displays eight
different headings:
1
11
1, (
((
(, 6
66
6, :
::
:, 1(
1(1(
1(, 1:
1:1:
1:, 6(
6(6(
6(, 6:
6:6:
6:
The compass does not disrupt receive or
transmit functions.
Alert Type Display Sound
Warning :
::
:1
11
1Siren
Watch :7
:7:7
:7 Siren
Statement 67
6767
67 Rapid Beep
Test 7(
7(7(
7( Rapid Beep
Channel Frequency (MHz)
WX 1 162.400
WX 2 162.425
WX 3 162.450
WX 4 162.475
WX 5 162.500
WX 6 162.525
WX 7 162.550

8
Calibrating the Electronic Com-
pass
You must calibrate the electronic compass in
your area before using it. The calibration al-
lows the electronic compass to separate the
earth’s magnetic field from the magnetic fields
generated by external influences such as your
vehicle so that the electronic compass pro-
vides accurate heading information.
Before beginning the calibration, you must in-
stall the CB in your vehicle. The calibration is
best performed on a leveled section of pave-
ment, such as an empty parking lot.
Notes:
• Depending on your vehicle’s wiring and
the placement of the CB in relation to the
magnetic fields created by that wiring,
there could be a slight delay in the CB
compass’ ability to calculate the correct
direction. For minimal delays in direc-
tional calculations, try different place-
ments of the CB installation. (See
“Mounting the CB” on Page 2.)
• You may need to recalibrate the compass
if you change the CB’s placement.
1. Set WX/CB/CMP to CMP.
2. Press and hold DUAL/MEM and press ACE/
ALERT OFF. &$
&$&$
&$ appears.
3. Press DUAL/MEM. &$
&$&$
&$ flashes.
4.Drive your car in a circle for two full turns.
5. Press DUAL/MEM.
Transmission Courtesy
Follow these guidelines when using your CB.
• Wait for a pause in someone else’s trans-
mission before you ask for a break.
• If you do not receive an answer to your
call after a second attempt, sign off and
wait several minutes before trying again.
• Do not hold down the talk button when
you are not talking. (This is called dead
keying).
• Assist callers with directions, information
about road conditions, and any other rea-
sonable requests.
Maximum Range
The maximum range and quality of CB trans-
missions vary depending on the following con-
ditions.
• the type and quality of antenna used
• the height of the antenna’s mounting
location — the higher the antenna, the
better the signal’s range
• the surrounding terrain mountains and tall
buildings limit the range
• weather conditions
• the number of nearby CBs operating on
the same channel
• standing wave ratio (SWR) between the
antenna and the CB.
Note: Your CB radio’s transmission range is
generally line-of-sight.
Reducing Noise
The Audio Clarity Enhance (ACE) circuit uses
compander (compressor and expander) tech-
nology to improve communication quality. The
circuit maintains the dynamic range while in-
creasing the signal-to-noise ratio as the gain
is automatically controlled according to the in-
put signal level. This results in a reduction in
wide band noise.
Because your CB is exceptionally quiet, any
noise you hear is probably from an external

9
source in you vehicle, such as the alternator,
another radio, or spark plugs.
To determine the noise’s source, turn off the
engine and operate the CB with your ignition
set to ACC. If the noise is reduced, the prob-
lem is your vehicle’s ignition or electrical sys-
tem.
Here are a few hints to reduce such noise:
• Make all CB power and antenna wires as
short as possible.
• Keep the power wires away from the
antenna wires.
• Be sure the chassis ground connection is
secure.
• Replace old ignition wires with new, high-
voltage, noise-suppression wires.
• Install noise suppressors on your spark
plugs, or install new spark plugs that
have built-in noise suppressors.
• If problems persist, check your alternator/
generator and regulator gauges. You can
reduce the noise from these sources by
using bypass capacitors at the various
output voltage points.
Your local RadioShack store has a wide se-
lectionofnoise-suppressionaccessories.
Using Common 10-Codes
CB users have adopted the 10-codes for standard questions and answers.
This table lists common codes adopted by the Associated Public Safety Communications Officers
(APCO).
CODE MEANING CODE MEANING
10-1 Receiving poorly 10-22 Report in person to
10-2 Receiving well 10-23 Please stand by
10-3 Stop transmitting 10-25 Can you contact
10-4 OK, message received 10-26 Disregard last information
10-5 Relay message 10-27 I am moving to channel
10-6 Busy, please stand by 10-28 Identify your station
10-7 Out of service 10-32 I will give you a radio check
10-8 In service 10-33 Emergency traffic
10-9 Repeat message 10-36 Correct time is
10-10 Transmission completed, standing by 10-37 Wrecker needed at
10-11 Talking too rapidly 10-38 Ambulance needed at
10-12 Visitors present 10-41 Please turn to channel
10-13 Advise Weather/road conditions 10-42 Traffic accident at
10-17 Urgent business 10-43 Traffic tie-up at
10-18 Anything for us 10-50 Break channel
10-19 Nothing for you. Return to base 10-62 Unable to copy; use telephone
10-20 My location is 10-70 Fire at
10-21 Call by telephone

10
TROUBLESHOOTING
We do not expect you to have any problem with your CB, but if you do, the following suggestions
might help.
If these tips do not solve the problem, do not attempt repairs or adjustments yourself. The CB
should be serviced only by a qualified radio technician. If you still have problems, take your CB to
your local RadioShack store for assistance.
Care
Keep the CB dry; if it gets wet, wipe it dry im-
mediately. Use and store the CB only in nor-
mal temperature environments. Handle the
CB carefully; do not drop it. Keep the CB
away from dust and dirt, and wipe it with a
damp cloth occasionally to keep it looking
new.
Modifying or tampering with the CB’s internal
components can cause a malfunction and
might invalidate its warranty and void your
FCC authorization to operate it. If your CB is
not performing as it should, take it to your lo-
cal RadioShack store for assistance.
Replacing the Fuse
The CB’s 2-amp in-line fuse helps protect
your CB from power surges and short circuits.
When replacement is required, use a 2-amp,
fast-acting glass fuse, available at your local
RadioShack store.
Follow these steps to replace the fuse.
1. Make sure the vehicle and CB are both
off.
Symptom Suggestion
Trouble receiving Make sure power is on. Turn VOLUME clockwise.
Make sure SQUELCH is adjusted properly.
Be sure RF GAIN is fully clockwise.
Make sure the CB is set to an operating channel.
Make sure the microphone is securely connected.
Press ACE/ALERT OFF to improve communication quality.
Check for a good antenna connection.
Make sure the antenna cable is securely connected to the antenna connector.
Make sure the antenna is fully extended.
Make sure all connections are secure and free of corrosion.
Make sure CB/WX/CMP is set to CB or CMP.
The CB is completely
inoperable Check the DC power cord and in-line fuse.
Replace the fuse. See “Replacing the Fuse” on Page 10.

11
2. Hold the fuse holder at both ends, push
the ends together, twist one end counter-
clockwise, and pull them apart.
3. Remove the old fuse and inspect its con-
dition. If it is blown, insert a new one of
the same type and rating. If it is not
blown, reinsert it.
Caution: Do not use a fuse with ratings
other then those specified here. Doing so
might damage your CB.
4. Push the fuse holder ends together and
twist one end clockwise.
SPECIFICATIONS
General
Channels ...................................................................................................................................... 40 Channels
Frequency Range ................................................................................................. 26.965 MHz to 27.405 MHz
Power Requirement ................................................................ 13.8V DC (12–16 Volts DC, Negative Ground)
Dimensions (HWD) ............................................................... 1.36 ×5.51 ×7.09 Inches (35 ×140 ×180 mm)
Weight ....................................................................................................................... 29.98 ounces (0.850 kg)
Receiver
Sensitivity ................................................................................................... 0.5µV or better for 10 dB (S+N)/N
Adjacent Channel Rejection ................................................................................................ 50 dB (at 10 kHz)
Audio Output ................................................................................................................. 4.5 Watts (Maximum)
Frequency Response ................................................................................................................. 450–2500 Hz
Intermediate Frequency
1st IF .............................................................................................................................................. 10.695 MHz
2nd IF .................................................................................................................................................. 455 kHz
Cross Modulation .................................................................................................................................... 50 dB
Squelch ......................................................................................................... Adjustable from 0.5 µV to 1 mV
Transmitter
Output Power ........................................................................................................... 4 Watts (FCC Maximum)
Type of Modulation................................................................... AM Double-Sideband, Full Carrier Modulation
Modulation Capability ............................................................................................................................. ± 90%
Spurious Emission ............................................................................................................... Less than – 70 dB
Frequency Tolerance ......................................................................................................................... ± 200 Hz
Antenna Impedance ............................................................................................................................ 50 Ohm
Current Drain (13.8-volt supply) .......................... 1 Amp with No Modulation (1.6 Amps with 80% Modulation)
Specifications are typical; individual units might vary. Specifications are subject to change and improvement
without notice.

08A01
21-1710 Printed in Thailand
Limited Ninety-Day Warranty
This product is warranted by RadioShack against manufacturing defects in material and workman-
ship under normal use for ninety (90) days from the date of purchase from RadioShack company-
owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED
HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES,
INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES
CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABIL-
ITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RE-
SPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE
OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WAR-
RANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVE-
NIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT,
SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN AD-
VISED OF THE POSSIBILITY OF SUCH DAMAGES.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limita-
tion of incidental or consequential damages, so the above limitations or exclusions may not apply to
you.
In the event of a product defect during the warranty period, take the product and the RadioShack
sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, un-
less otherwise provided by law: (a) correct the defect by product repair without charge for parts and
labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase
price. All replaced parts and products, and products on which a refund is made, become the prop-
erty of RadioShack. New or reconditioned parts and products may be used in the performance of
warranty service. Repaired or replaced parts and products are warranted for the remainder of the
original warranty period. You will be charged for repair or replacement of the product made after the
expiration of the warranty period.
This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse,
accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or
maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs
other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as
fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs
of product removal, installation, set-up service adjustment or reinstallation.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102
We Service What We Sell 12/99