Raisecom RC953-GESTM1 Installation instructions

www.raisecom.com
RC953-GESTM1 Commands Notebook

Legal Notices
Raisecom Technology Co., Ltd makes no warranty of any kind with regard to this manual,
including, but not limited to, the implied warranties of merchantability and fitness for a particular
purpose. Raisecom Technology Co., Ltd shall not be held liable for errors contained herein or direct,
indirect, special, incidental or consequential damages in connection with the furnishing, performance,
or use of this material.
Warranty.
A copy of the specific warranty terms applicable to your Raisecom product and replacement parts
can be obtained from Service Office.
Restricted Rights Legend.
All rights are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Raisecom Technology Co., Ltd. The
information contained in this document is subject to change without notice.
Copyright Notices.
Copyright ©2007 Raisecom. All rights reserved.
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in
Writing from Raisecom Technology Co., Ltd.
Trademark Notices
is the trademark of Raisecom Technology Co., Ltd.
Java™ is a U.S. trademark of Sun Microsystems, Inc.
Microsoft® is a U.S. registered trademark of Microsoft Corporation.
Windows NT® is a U.S. registered trademark of Microsoft Corporation.
Windows® 2000 is a U.S. registered trademark of Microsoft Corporation.
Windows® XP is a U.S. registered trademark of Microsoft Corporation.
Windows® and MS Windows® are U.S. registered trademarks of
Microsoft Corporation.

Contact Information
Technical Assistance Center
The Raisecom TAC is available to all customers who need technical assistance with a Raisecom
product, technology, or, solution. You can communicate with us through the following methods:
Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road,
Haidian District, Beijing 100085
Tel: [phone]
Fax: [phone]
World Wide Web
You can access the most current Raisecom product information on the World Wide Web at the
following URL:
http://www.raisecom.com
Feedback
Comments and questions about how the RC953-GESTM1 device works are welcomed. Please
review the FAQ in the related manual, and if your question is not covered, send email by using the
following web page:
http://www.raisecom.com/en/xcontactus/contactus.htm.
If you have comments on the RC953-GESTM1 specification, instead of the web page above, please
send comments to:
[email protected]
We hope to hear from you!

CONTENTS
Chapter 1 How to Use the Command Line---------------------------------------------1
1.1 Environment --------------------------------------------------------------------------------------------------------------------1
1.2 Command line format explanation----------------------------------------------------------------------------------------1
1.3 Command mode---------------------------------------------------------------------------------------------------------------1
1.4 Relationship of command modes -----------------------------------------------------------------------------------------3
1.5 Commands in different command mode --------------------------------------------------------------------------------3
Chapter 2 System Management Commands----------------------------------------- 10
2.1 chinese-------------------------------------------------------------------------------------------------------------------------10
2.2 clear-----------------------------------------------------------------------------------------------------------------------------10
2.3 config ---------------------------------------------------------------------------------------------------------------------------11
2.4 device unlock----------------------------------------------------------------------------------------------------------------- 11
2.5 device lock --------------------------------------------------------------------------------------------------------------------12
2.6 device clock-mode ----------------------------------------------------------------------------------------------------------12
2.7 disable--------------------------------------------------------------------------------------------------------------------------13
2.8 enable --------------------------------------------------------------------------------------------------------------------------14
2.9 english--------------------------------------------------------------------------------------------------------------------------15
2.10 end-----------------------------------------------------------------------------------------------------------------------------15
2.11 exit -----------------------------------------------------------------------------------------------------------------------------16
2.12 help----------------------------------------------------------------------------------------------------------------------------17
2.13 interface----------------------------------------------------------------------------------------------------------------------18
2.14 history-------------------------------------------------------------------------------------------------------------------------18
2.15 hostname --------------------------------------------------------------------------------------------------------------------19
2.16 list------------------------------------------------------------------------------------------------------------------------------20
2.17 logout -------------------------------------------------------------------------------------------------------------------------20
2.18 quit-----------------------------------------------------------------------------------------------------------------------------21
2.19 reboot-------------------------------------------------------------------------------------------------------------------------22
2.20 settime------------------------------------------------------------------------------------------------------------------------22
2.21 show clock-------------------------------------------------------------------------------------------------------------------23
2.22 show cpu-utilization-ratio ------------------------------------------------------------------------------------------------23
2.23 show device-----------------------------------------------------------------------------------------------------------------24
2.24 show device clock ---------------------------------------------------------------------------------------------------------25
2.25 show sntp--------------------------------------------------------------------------------------------------------------------25
2.26 show terminal---------------------------------------------------------------------------------------------------------------26
2.27 show version----------------------------------------------------------------------------------------------------------------27
2.28 sntp server-------------------------------------------------------------------------------------------------------------------27
2.29 terminal history-------------------------------------------------------------------------------------------------------------28
2.30 terminal line -----------------------------------------------------------------------------------------------------------------29
2.31 terminal time-out-----------------------------------------------------------------------------------------------------------30
2.32 who----------------------------------------------------------------------------------------------------------------------------30
Chapter 3 RC953-GESTM1 User Management Commands--------------------- 32
3.1 password ----------------------------------------------------------------------------------------------------------------------32
3.2 save user----------------------------------------------------------------------------------------------------------------------33
3.3 show user ---------------------------------------------------------------------------------------------------------------------33
3.4 user -----------------------------------------------------------------------------------------------------------------------------34
3.5 user privilege -----------------------------------------------------------------------------------------------------------------35
Chapter 4 Log management commands of RC953-GESTM1-------------------- 37
4.1 log -------------------------------------------------------------------------------------------------------------------------------37
4.2 log clear------------------------------------------------------------------------------------------------------------------------37
4.3 show log -----------------------------------------------------------------------------------------------------------------------38
Chapter 5 Network protocols configuration commands of RC953-GESTM140
5.1 arp add-------------------------------------------------------------------------------------------------------------------------40
5.2 arp delete----------------------------------------------------------------------------------------------------------------------40
5.3 ip address ---------------------------------------------------------------------------------------------------------------------41
5.4 ip route -------------------------------------------------------------------------------------------------------------------------42

5.5 no virtual-channel -----------------------------------------------------------------------------------------------------------43
5.6 ping------------------------------------------------------------------------------------------------------------------------------43
5.7 show arp-----------------------------------------------------------------------------------------------------------------------44
5.8 show ip route -----------------------------------------------------------------------------------------------------------------45
5.9 show snmp-server community-------------------------------------------------------------------------------------------46
5.10 show snmp trap-sever----------------------------------------------------------------------------------------------------46
5.11 snmp-server community--------------------------------------------------------------------------------------------------47
5.12 snmp-server contact SYSCONTACT---------------------------------------------------------------------------------48
5.13 snmp-server location SYSLOCATION -------------------------------------------------------------------------------49
5.14 snmp-server name SYSNAME-----------------------------------------------------------------------------------------49
5.15 snmp trap-server-----------------------------------------------------------------------------------------------------------50
5.16 snmpd ------------------------------------------------------------------------------------------------------------------------50
5.17 show snmp-server statistics---------------------------------------------------------------------------------------------51
5.18 show interface snmp------------------------------------------------------------------------------------------------------52
5.19 show interface vcc---------------------------------------------------------------------------------------------------------53
5.20 virtual-channel--------------------------------------------------------------------------------------------------------------53
Chapter 6 Upgrade and configuration file management commands of
RC953-GESTM1 ---------------------------------------------------------------------------- 54
6.1 download--------------------------------------------------------------------------------------------------------------------54
6.2 erase startup-config ------------------------------------------------------------------------------------------------------55
6.3 show running-config------------------------------------------------------------------------------------------------------56
6.4 show startup-config device <0-127> ---------------------------------------------------------------------------------57
6.5 show startup-config-------------------------------------------------------------------------------------------------------58
6.6 upload------------------------------------------------------------------------------------------------------------------------59
6.7 write---------------------------------------------------------------------------------------------------------------------------60
Chapter 7 Alarming management command of RC953-GESTM1-------------- 62
7.1 alarm-trap-disable---------------------------------------------------------------------------------------------------------62
7.2 alarm-trap-disable index-------------------------------------------------------------------------------------------------62
7.3 alarm-trap-disable sdh---------------------------------------------------------------------------------------------------63
7.4 show current-alarm -------------------------------------------------------------------------------------------------------64
7.5 show history-alarm--------------------------------------------------------------------------------------------------------64
7.6 show alarm-index ---------------------------------------------------------------------------------------------------------65
Chapter 8 Interface management command of RC953-GESTM1 SDH-------- 67
8.1 sdh description-------------------------------------------------------------------------------------------------------------67
8.2 loopback---------------------------------------------------------------------------------------------------------------------67
8.3 sdh aps-restore-time -----------------------------------------------------------------------------------------------------68
8.4 sdh aupje-threshold-------------------------------------------------------------------------------------------------------68
8.5 sdh force-switch -----------------------------------------------------------------------------------------------------------69
8.6 sdh exc-threshold ---------------------------------------------------------------------------------------------------------69
8.7 sdh es-threshold-----------------------------------------------------------------------------------------------------------70
8.8 sdh overhead c2-----------------------------------------------------------------------------------------------------------71
8.9 sdh overhead j0------------------------------------------------------------------------------------------------------------71
8.10 sdh overhead j1----------------------------------------------------------------------------------------------------------72
8.11 sdh overhead j2----------------------------------------------------------------------------------------------------------72
8.12 sdh overhead s1---------------------------------------------------------------------------------------------------------73
8.13 sdh sd-threshold---------------------------------------------------------------------------------------------------------73
8.14 sdh ses-threshold--------------------------------------------------------------------------------------------------------74
8.15 show sdh aps-------------------------------------------------------------------------------------------------------------75
8.16 show sdh aps timeslot--------------------------------------------------------------------------------------------------75
8.17 sdh tuais-insert-----------------------------------------------------------------------------------------------------------76
8.18 show interface sdh ------------------------------------------------------------------------------------------------------77
8.19 show interface sdh <1-2> timeslot ----------------------------------------------------------------------------------77
Chapter 9 Management Command of RC953-GESTM1 E1 --------------------- 79
9.1 batch-e1 ---------------------------------------------------------------------------------------------------------------------79
9.2 batch loopback-detection -----------------------------------------------------------------------------------------------79
9.3 bert----------------------------------------------------------------------------------------------------------------------------80
9.4 clock-mode------------------------------------------------------------------------------------------------------------------80
9.5 crc-auto----------------------------------------------------------------------------------------------------------------------81
9.6 frame -------------------------------------------------------------------------------------------------------------------------81

9.7 interface e1 -----------------------------------------------------------------------------------------------------------------82
9.8 loopback-detection--------------------------------------------------------------------------------------------------------82
9.9 inter-connection------------------------------------------------------------------------------------------------------------83
9.10 remote-e1-loopback-----------------------------------------------------------------------------------------------------83
9.11 reset-statistics ------------------------------------------------------------------------------------------------------------84
9.12 show interface e1 occupy status ------------------------------------------------------------------------------------84
9.13 show interface e1--------------------------------------------------------------------------------------------------------87
9.14 timeslot---------------------------------------------------------------------------------------------------------------------87
9.15 unframe --------------------------------------------------------------------------------------------------------------------88
Chapter 10 Virtual-channel command of RC953-GESTM1 -------------------- 89
10.1 batch virtual-channel----------------------------------------------------------------------------------------------------89
10.2 err-auto-shutdown-------------------------------------------------------------------------------------------------------89
10.3 no virtual-channel index------------------------------------------------------------------------------------------------90
10.4 no virtual channel name -----------------------------------------------------------------------------------------------90
10.5 show virtual-channel----------------------------------------------------------------------------------------------------91
10.6 show virtual-channel name -------------------------------------------------------------------------------------------92
10.7 virtual-channel index----------------------------------------------------------------------------------------------------92
10.8 virtual-channel------------------------------------------------------------------------------------------------------------93
Chapter 11 Interface management command of RC953-GESTM1 -------------- 94
Description -------------------------------------------------------------------------------------------------------------------------94
flow-control-------------------------------------------------------------------------------------------------------------------------94
11.3 no rate-limit----------------------------------------------------------------------------------------------------------------95
11.4 rate-burst-------------------------------------------------------------------------------------------------------------------95
11.5 rate-limit--------------------------------------------------------------------------------------------------------------------96
11.6 re-autoneg-----------------------------------------------------------------------------------------------------------------97
11.7 reset-statistics ------------------------------------------------------------------------------------------------------------97
11.8 sfp-switch ------------------------------------------------------------------------------------------------------------------98
11.9 show interface ge--------------------------------------------------------------------------------------------------------98
11.10 shutdown-----------------------------------------------------------------------------------------------------------------99
11.11 storm-rate-limit-------------------------------------------------------------------------------------------------------- 100
11.12 storm-suppression --------------------------------------------------------------------------------------------------- 100
11.13 vc12 add---------------------------------------------------------------------------------------------------------------- 101
11.14 virtual-channel add -------------------------------------------------------------------------------------------------- 101
11.15 virtual-channel delete ----------------------------------------------------------------------------------------------- 102
11.16 trunk --------------------------------------------------------------------------------------------------------------------- 103
Chapter 12 Remote device management command of RC953-GESTM1-------104
12.1 remote ric---------------------------------------------------------------------------------------------------------------- 104
12.2 show remote ric-------------------------------------------------------------------------------------------------------- 104
12.3 show remote interface ric <1-63> e1----------------------------------------------------------------------------- 105
12.4 show remote interface ric <1-63> eth ---------------------------------------------------------------------------- 105
Chapter 13 Device management command of remote RC952-FEE1------------107
13.1 device-name------------------------------------------------------------------------------------------------------------ 107
13.2 device-type-------------------------------------------------------------------------------------------------------------- 107
13.3 fault-pass ---------------------------------------------------------------------------------------------------------------- 108
13.4 interface------------------------------------------------------------------------------------------------------------------ 108
13.5 reset----------------------------------------------------------------------------------------------------------------------- 108
13.6 show device------------------------------------------------------------------------------------------------------------- 109
Chapter 14 The configuration command under the e1 interface configuration mode of
remote RC952-FEE1----------------------------------------------------------------------- 110
14.1 clock-mode-------------------------------------------------------------------------------------------------------------- 110
14.2 crc-auto ------------------------------------------------------------------------------------------------------------------110
14.3 interface -----------------------------------------------------------------------------------------------------------------111
14.4 show interface ---------------------------------------------------------------------------------------------------------111
Chapter 15 The configuration command under the e1 interface configuration mode of
remote RC952-FEE1.---------------------------------------------------------------------- 113
15.1 autonegotiate----------------------------------------------------------------------------------------------------------- 113
15.2 flow-control--------------------------------------------------------------------------------------------------------------113
15.3 interface------------------------------------------------------------------------------------------------------------------ 114

15.4 show interface---------------------------------------------------------------------------------------------------------- 114
15.5 shutdown ---------------------------------------------------------------------------------------------------------------- 115
15.6 speed duplex ----------------------------------------------------------------------------------------------------------- 115
Chapter 16 Device management command of remote RC952-FXE1 ---------- 117
16.1 device-name------------------------------------------------------------------------------------------------------------ 117
16.2 device-type-------------------------------------------------------------------------------------------------------------- 117
16.3 interface------------------------------------------------------------------------------------------------------------------ 118
16.4 reset----------------------------------------------------------------------------------------------------------------------- 118
16.5 show device------------------------------------------------------------------------------------------------------------- 119
Chapter 17 The configuraiton command under the e1Interface configuration mode
of remote RC952-FXE1. ------------------------------------------------------------------120
17.1 clock-mode-------------------------------------------------------------------------------------------------------------- 120
17.2 crc-auto ------------------------------------------------------------------------------------------------------------------ 120
17.3 interface------------------------------------------------------------------------------------------------------------------ 121
17.4 show interface---------------------------------------------------------------------------------------------------------- 121
Chapter 18 The configuration mode under the fxInterface configuration mode of
remote RC952-FXE1.----------------------------------------------------------------------123
18.1 flow-control-------------------------------------------------------------------------------------------------------------- 123
18.2 interface------------------------------------------------------------------------------------------------------------------ 123
18.3 show interface---------------------------------------------------------------------------------------------------------- 124
Chapter 19 Device management command of remote RC951-FEE1------------125
Chapter 20 Device management command of remote RC953-FE8E1 ----------126
20.1 device-name------------------------------------------------------------------------------------------------------------ 126
20.2 device-type-------------------------------------------------------------------------------------------------------------- 126
20.3 err-auto-shutdown----------------------------------------------------------------------------------------------------- 127
20.4 fault-pass ---------------------------------------------------------------------------------------------------------------- 127
20.5 interface e1-------------------------------------------------------------------------------------------------------------- 127
20.6 interface eth------------------------------------------------------------------------------------------------------------- 128
20.7 reset----------------------------------------------------------------------------------------------------------------------- 128
20.8 show device------------------------------------------------------------------------------------------------------------- 129
Chapter 21 The configuration mode under the e1 Interface configuration mode of
remote RC953-FE8E1. --------------------------------------------------------------------130
21.1 clock-mode-------------------------------------------------------------------------------------------------------------- 130
21.2 crc-auto --------------------------------------------------------------------------------------------------------------- 130
21.3 interface e1-------------------------------------------------------------------------------------------------------------- 131
21.4 interface eth------------------------------------------------------------------------------------------------------------- 131
21.5 show interface---------------------------------------------------------------------------------------------------------- 131
Chapter 22 The configuration command under eth Interface configuration mode of
remote RC953-FE8E1. --------------------------------------------------------------------133
22.1 autonegotiate----------------------------------------------------------------------------------------------------------- 133
22.2 flow-control-------------------------------------------------------------------------------------------------------------- 133
22.3 interface e1-------------------------------------------------------------------------------------------------------------- 134
22.4 show interface---------------------------------------------------------------------------------------------------------- 134
22.5 shutdown ---------------------------------------------------------------------------------------------------------------- 135
22.6 speed duplex ----------------------------------------------------------------------------------------------------------- 135
Chapter 23 The device management command of remote RC953-FX8E1. ----137
23.1 device-name------------------------------------------------------------------------------------------------------------ 137
23.2 device-type-------------------------------------------------------------------------------------------------------------- 137
23.3 err-auto-shutdown----------------------------------------------------------------------------------------------------- 138
23.4 interface e1-------------------------------------------------------------------------------------------------------------- 138
23.5 interface fx-eth --------------------------------------------------------------------------------------------------------- 138
23.6 reset----------------------------------------------------------------------------------------------------------------------- 139
23.7 show device------------------------------------------------------------------------------------------------------------- 139
Chapter 24 The configuration command under e1 Interface configuration mode of
remote RC953-FX8E1. --------------------------------------------------------------------141
24.1 clock-mode-------------------------------------------------------------------------------------------------------------- 141

24.2 crc-auto ------------------------------------------------------------------------------------------------------------------ 141
24.3 interface e1-------------------------------------------------------------------------------------------------------------- 142
24.4 interface fx-eth --------------------------------------------------------------------------------------------------------- 142
24.5 show interface---------------------------------------------------------------------------------------------------------- 142
Chapter 25 The configuration command under fxInterface configuration mode of
remote RC953-FX8E1---------------------------------------------------------------------144
25.1 flow-control-------------------------------------------------------------------------------------------------------------- 144
25.2 interface e1-------------------------------------------------------------------------------------------------------------- 144
25.3 show interface---------------------------------------------------------------------------------------------------------- 145
Chapter 26 The device management command of remote RC953-FE4E1.---146
26.1 device-name------------------------------------------------------------------------------------------------------------ 146
26.2 device-type-------------------------------------------------------------------------------------------------------------- 146
26.3 err-auto-shutdown----------------------------------------------------------------------------------------------------- 147
26.4 fault-pass ---------------------------------------------------------------------------------------------------------------- 147
26.5 interface e1-------------------------------------------------------------------------------------------------------------- 147
26.6 interface eth------------------------------------------------------------------------------------------------------------- 148
26.7 reset----------------------------------------------------------------------------------------------------------------------- 148
26.8 show device------------------------------------------------------------------------------------------------------------- 149
Chapter 27 The configuration command under e1Interface configuration mode of
remote RC953-FE4E1. --------------------------------------------------------------------150
27.1 clock-mode-------------------------------------------------------------------------------------------------------------- 150
27.2 crc-auto ------------------------------------------------------------------------------------------------------------------ 150
27.3 interface e1-------------------------------------------------------------------------------------------------------------- 151
27.4 interface eth------------------------------------------------------------------------------------------------------------- 151
27.5 show interface---------------------------------------------------------------------------------------------------------- 151
Chapter 28 The configuration command under ethInterface configuration mode of
remote RC953-FE4E1. --------------------------------------------------------------------153
28.1 autonegotiate----------------------------------------------------------------------------------------------------------- 153
28.2 flow-control-------------------------------------------------------------------------------------------------------------- 153
28.3 interface e1-------------------------------------------------------------------------------------------------------------- 154
28.4 show interface---------------------------------------------------------------------------------------------------------- 154
28.5 shutdown ---------------------------------------------------------------------------------------------------------------- 155
28.6 speed duplex ----------------------------------------------------------------------------------------------------------- 155
Chapter 29 The device management command of remote RC953-FX4E1.---157
29.1 device-name------------------------------------------------------------------------------------------------------------ 157
29.2 device-type-------------------------------------------------------------------------------------------------------------- 157
29.3 err-auto-shutdown----------------------------------------------------------------------------------------------------- 158
29.4 interface e1-------------------------------------------------------------------------------------------------------------- 158
29.5 interface fx-eth --------------------------------------------------------------------------------------------------------- 158
29.6 reset----------------------------------------------------------------------------------------------------------------------- 159
29.7 show device------------------------------------------------------------------------------------------------------------- 159
Chapter 30 The comfiguration command under e1 Interface configuration mode of
remote RC953-FX4E1. --------------------------------------------------------------------161
30.1 clock-mode-------------------------------------------------------------------------------------------------------------- 161
30.2 crc-auto ------------------------------------------------------------------------------------------------------------------ 161
30.3 interface e1-------------------------------------------------------------------------------------------------------------- 162
30.4 interface fx-eth --------------------------------------------------------------------------------------------------------- 162
30.5 show interface---------------------------------------------------------------------------------------------------------- 162
Chapter 31 The configuration command under fxInterface configuration mode of
remote RC953-FX4E1. --------------------------------------------------------------------164
31.1 flow-control-------------------------------------------------------------------------------------------------------------- 164
31.2 interface e1-------------------------------------------------------------------------------------------------------------- 164
31.3 show interface---------------------------------------------------------------------------------------------------------- 165
Chapter 32 The device management command of remote RC954-FE4E1. ----166
32.1 device-name--------------------------------------------------------------------------------------------------------- 166
32.2 device-type-------------------------------------------------------------------------------------------------------------- 166

32.3 err-auto-shutdown----------------------------------------------------------------------------------------------------- 167
32.4 fault-pass ---------------------------------------------------------------------------------------------------------------- 167
32.5 interface e1-------------------------------------------------------------------------------------------------------------- 167
32.6 interface eth------------------------------------------------------------------------------------------------------------- 168
32.7 reset----------------------------------------------------------------------------------------------------------------------- 168
32.8 show device------------------------------------------------------------------------------------------------------------- 169
Chapter 33 The configuration command under e1Interface configuration mode of
remote RC954-FE4E1. --------------------------------------------------------------------170
33.1 clock-mode-------------------------------------------------------------------------------------------------------------- 170
33.2 crc-auto ------------------------------------------------------------------------------------------------------------------ 170
33.3 interface e1-------------------------------------------------------------------------------------------------------------- 171
33.4 interface eth------------------------------------------------------------------------------------------------------------- 171
33.5 show interface---------------------------------------------------------------------------------------------------------- 171
Chapter 34 The configuration command under ethInterface configuration mode of
remote RC954-FE4E1. --------------------------------------------------------------------173
34.1 autonegotiate----------------------------------------------------------------------------------------------------------- 173
34.2 flow-control-------------------------------------------------------------------------------------------------------------- 173
34.3 interface e1-------------------------------------------------------------------------------------------------------------- 174
34.4 show interface---------------------------------------------------------------------------------------------------------- 174
34.5 shutdown ---------------------------------------------------------------------------------------------------------------- 175
34.6 speed duplex ----------------------------------------------------------------------------------------------------------- 175
Chapter 35 The device management command of remote RC954-FX4E1. ----177
35.1 device-name------------------------------------------------------------------------------------------------------------ 177
35.2 device-type-------------------------------------------------------------------------------------------------------------- 177
35.3 err-auto-shutdown----------------------------------------------------------------------------------------------------- 178
35.4 interface e1-------------------------------------------------------------------------------------------------------------- 178
35.5 interface fx-eth --------------------------------------------------------------------------------------------------------- 178
35.6 reset----------------------------------------------------------------------------------------------------------------------- 179
35.7 show device------------------------------------------------------------------------------------------------------------- 179
Chapter 36 The configuration command under e1Interface configuration mode of
remote RC954-FX4E1. --------------------------------------------------------------------181
36.1 clock-mode-------------------------------------------------------------------------------------------------------------- 181
36.2 crc-auto ------------------------------------------------------------------------------------------------------------------ 181
36.3 interface e1-------------------------------------------------------------------------------------------------------------- 182
36.4 interface fx-eth --------------------------------------------------------------------------------------------------------- 182
36.5 show interface---------------------------------------------------------------------------------------------------------- 182
Chapter 37 The configuration command under fxInterface configuration mode of
remote RC954-FX4E1. --------------------------------------------------------------------184
37.1 flow-control-------------------------------------------------------------------------------------------------------------- 184
37.2 interface e1-------------------------------------------------------------------------------------------------------------- 184
37.3 show interface---------------------------------------------------------------------------------------------------------- 185

Release Notes
Date of Release Manual Version Software Version Revisions
20071210 20071109

Preface
Why we write this manual
The main aim of writing this user manual RC953-GESTM1is to introduce the software Command
line interface of RC953-GESTM1, it wholly introduces the Command line human interface that is
setup by RC953-GESTM1, meanwhile it can finished the management according to the whole device
of RC953-GESTM1, including the management and configuration of different kinds of interface
and remote device, then it used for RC953-GESTM1 device and related RC953-GESTM1 software
edition customers.
Relevant manual
《RC953-GESTM1Configuration Guide Manual》
This manual is《RC953-GESTM1 Commands Notebook》

www.raisecom.com User Manual
1
Chapter 1 How to Use the Command Line
1.1 Environment
Hardware environment: RC953-GESTM1device platform
Computer serial ports;
Software environment: WIN98 / WIN2000 / WINDOWS XP
1.2 Command line format explanation
symbol Explanation
<> Indicate this part is a confirmed range of parameter
| Divide the several options of the parameter.
[ ] Indicate this part is optional choice and can not be
impute.
( ) Necessary impute parameter or Command key words.
1．Only write the Commands in front of the Command key words of the first parameter.
2．Use “[]” in the place of the optional choice for both the signal and multiple parameter, use “|” between
two multiple parameter.
3．If the necessary impute parameter or Command key words are optional, use the symbol “()”, use “|”
between two multiple parameter.
1.3 Command mode
Mode Description Access function Mode symbol
User EXEC Mode Under this mode, user can
configuration the terminal basic
information or indicate the
parameter.
Sign up the device, enter the
ID No. and password.
RC953-GESTM1>

www.raisecom.com User Manual
2
Privileged EXEC
mode
Under this mode, customers can
configuration the basic
information of RC953-GESTM1
device, for instance the system
time, indicate the parameter
information. It can’t
configuration the working
information of the device.
Enter the enable and password
under the common customer’s
mode.
RC953-GESTM1#
Global
configuration
mode
Under this mode, costumers can
configuration all the device
working parameters of
RC953-GESTM1.
Enter config under the
Privileged EXEC mode.
RC953-GESTM1
(config)#
Local interface
configuration
mode.
Under this mode, costumers can
configuration the parameters of
the SNMP interface, Eth
interface, SDH interface and
internal E1 interface.
Enter interface {ge/sdh/
e1/snmp/vcc} X under Global
configuration mode.
RC953-GESTM1
(config-xxx/X)#
Xindicates the interface
No.
Remote interface
converter
configuration
mode
Under this mode, costumers can
configuration the working
parameters of the remote
interface converter device.
Enter remote ric X under the
Global configuration mode.
RC953-GESTM1
(config)#remote ric X
RC953-GESTM1
(config-RIC/X)#
RIC indicates the real
style of the remote
interface converter
products.
Remote
interface
converter
interface
configuration
mode.
Under this mode, customers
can configuration the remote
interface converter device
interface.
Enter interface{eth/e1}
under the remote
converter configuration
mode.
RC953-GESTM1(co
nfig-RC952FEE1/X)
#interface eth [Y]
RC953-GESTM1(co
nfig-RC952FEE1/X-
eth/Y)#

www.raisecom.com User Manual
3
Remote
media
converter
configuration
mode.
Under this mode, costumers
can configuration the
working parameters of the
remote media converter.
Enter remote rmc under
the Global configuration
mode.
RC953-GESTM1(co
nfig)#remote rmc X
RC953-GESTM1
(config-RC501/X)#
Remote
media
converter
interface
configuration
mode.
Under this mode, costumers
can configuration the
interface of the remote
media converter device.
Enter interface
{eth/fx-eth} under the
remote media converter
configuration mode.
RC953-GESTM1(co
nfig-RC501/X)#inte
rface eth Y
RC953-GESTM1
(config-RC501/X-et
h/Y)#
1.4 Relationship of command modes
User EXEC
mode
Privileged
EXEC mode
Global
Configuration mode
Interface
SDH mode
Interface E1
mode
Interface GE
mode
Remote Interface
converter mode Interface Eth mode of
remote Interface Converter
Interface E1 mode of
remote Interface Converter
Interface SNMP
mode
1.5 Commands in different command mode
Command mode Command list
User EXEC mode Chinese
clear
enable

www.raisecom.com User Manual
4
English
exit
help
history
list
no terminal line
quit
terminal history <1-20>
terminal line <5-512>
terminal time-out <0-65535>
Privileged EXEC mode chinese
clear
config terminal
config
debug
device unlock
disable
download (system-boot | startup-config) (tftp | ftp)
english
erase startup-config
exit
help
history
hostname HOSTNAME
list
logout
no hostname
no user USERNAME
password
ping A.B.C.D [count <1-65535>] [size <12-4076>] [timeout <1-255>]
quit
reboot
save user
set time DATE TIME
show alarm index [(sdh|innere1|system|rmc|ric|ge)]
show arp
show clock
show cpu-utilization-ratio
show current-alarm
show device
show device clock
show history-alarm
show interface e1 occupy status
show interface e1 [<1-63>]
show interface ge <1-2>
show interface sdh <1-2> timeslot [<1-63>]
show interface sdh [<1-2>]
show interface SNMP
show interface vcc
show ip route help
showiproute
show log [key1 STRING] [key2 STRING] [key3 STRING]
show remote interface ric <1-63> e1 [<1-8>]
show remote interface ric <1-63> (eth|fx-eth)
show remote interface rmc <1-63> (eth|fx-eth)
show remote ric
show remote ric <1-63>
show remote rmc
show remote rmc <1-63>

www.raisecom.com User Manual
5
show running-config
showsdhaps
show sdh aps timeslot [TSSTRING]
show SNMP-server community
show SNMP-server statistics
show SNMP trap-server
show sntp
show startup-config
show startup-config device <0-127>
show terminal
show user
show version
show virtual-channel [<1-63>]
upload (system-boot | startup-config) (tftp|ftp)
user USERNAME password (no-encryption|md5) PASSWORD
user USERNAME privilege (administrant|normal|limited)
who
write
Global configuration mode alarm-trap-disable
alarm-trap-disable (ric|rmc|system|innere1|ge)
alarm-trap-disable index ALARMNO
alarm-trap-disable sdh [(section|line|path|tu|vc)]
arp add A.B.C.D MACADDR
arp delete A.B.C.D
batch-e1 [{1-63}] (frame|unframe)
batch virtual-channel vc12 TSSTRING e1 E1STRING [e1num<1-8>]
chinese
clear
device clock-mode (master|slave)
device lock
end
english
[no] err-auto-shutdown virtual-channel {1-63}
exit
help
history
interface e1 <1-63>
interface ge <1-2>
interface sdh <1-2>
interfaceSNMP
interface vcc
ip route A.B.C.D A.B.C.D A.B.C.D
list
log (enable|disable)
log clear
loopbackdetection (enable|disable) virtual-channel {1-63}
no alarm-trap-disable
no alarm-trap-disable (ric|rmc|system|innere1|ge)
no alarm-trap-disable index ALARMNO
no alarm-trap-disable sdh [(section|line|path|tu|vc)]
no ip route A.B.C.D A.B.C.D
no SNMP-server community COMMUNITYNAME
no snmpd
no SNMP trap-server A.B.C.D
no sntp server
no virtual-channel index {1-63}
no virtual-channel name STRING
quit
remote ric <1-63>

www.raisecom.com User Manual
6
remote rmc <1-63>
sdh aps-restore-time <1-12>
sdh force-switch (work-line|protection-line|clear) timeslot [TSSTRING]
show alarmindex [(sdh|innere1|system|rmc|ric|ge)]
show arp
show current-alarm
show device
show device clock
show ip route help
showiproute
show log [key1 STRING] [key2 STRING] [key3 STRING]
show loopbackdetection virtual-channel [{1-63}]
show remote interface ric <1-63> e1 [<1-8>]
show remote interface ric <1-63> (eth|fx-eth)
show remote interface rmc <1-63> (eth|fx-eth)
show remote ric
show remote ric <1-63>
showremotermc
show remote rmc <1-63>
show sdh aps
show sdh aps timeslot [TSSTRING ]
show snmp-server community
show snmp-server statistics
show snmp trap-server
show sntp
show virtual-channel [<1-63>]
snmp-server community COMMUNITYNAME (ro|rw)
snmp-server contact SYSCONTACT
snmp-server location SYSLOCATION
snmp-server name SYSNAME
snmpd
snmp trap-server A.B.C.D [<1-65535>]
sntp server A.B.C.D
virtual-channel index <1-63> name STRING
virtual-channel vc12 TSSTRING e1 E1STRING [index <1-63>] [name STRING]
GE interface configuration
mode chinese
clear
description STRING
end
english
exit
flow-control (on|off)
help
history
interface ge <1-2>
list
no rate-limit (ingress-rate|engress-rate)
no shutdown
no storm-suppression (broadcast|multicast|dlfstorm|all)
no trunk
quit
rate-burst (ingress-rate|engress-rate) (6kb|10kb|18kb|34kb|66kb|130kb)
rate-limit (ingress-rate|engress-rate) <1-1024000> [burst
(6kb|10kb|18kb|34kb|66kb|130kb)]
reset-statistics
sfp-switch (on|off)
show interface
show interface ge <1-2>
show trunk

www.raisecom.com User Manual
7
shutdown
storm-rate-limit <0-1024000>
storm-suppression (broadcast|multicast|dlfstorm|all)
trunk
vc12 add VC12STRING [vc12num <1-8>]
virtual-channel add VCSTRING
virtual-channel delete [VCSTRING]
E1 interface configuration
mode bert (enable|disable)
chinese
clear
clock-mode (master|slave)
crc-auto (enable|disable)
end
english
exit
frame
help
history
interface e1 <1-63>
list
no remote-e1-loopback
quit
remote-e1-loopback
reset-statistics
show interface
show interface e1 occupystatus
show interface e1 <1-63>
show interface e1
timeslot TSSTRING
unframe
SDH interface configuration
mode chinese
clear
end
english
exit
help
history
interface sdh <1-2>
list
loopback (local|remote)
no loopback
quit
sdh aupje-threshold (positive|negative) <1-65535>
sdh Description STRING
sdh es-threshold (section|line|higher-path|lower-path) <1-900>
sdh exc-threshold (section|line|higher-path|lower-path) <3-5>
sdh j0tim (enable|disable)
sdh overhead c2 [expected BYTE] [transmit BYTE]
sdh overhead j0 [expected EXPMSG] [transmit XMITMSG]
sdh overhead j1 [expected EXPMSG] [transmit XMITMSG]
sdh overhead j2 [vc12 <1-63>] [expected EXPMSG] [transmit XMITMSG]
sdh overhead s1 BYTE
sdh sd-threshold (section|line|higher-path|lower-path) <6-8>
sdh ses-threshold (section|line|higher-path|lower-path) <1-900>
sdh tuais-insert (sectiontim|linesd|pathsd|pathplm|pathtim) (enable|disable)
show interface
show interface sdh <1-2> timeslot [<1-63>]
show interface sdh [<1-2>]
Snmp interface mode autonegotiate

www.raisecom.com User Manual
8
chinese
clear
description STRING
end
english
exit
help
history
ip address A.B.C.D A.B.C.D
ip address A.B.C.D
list
no autonegotiate
no shutdown
quit
show interface
show interface snmp
shutdown
speed (10|100) duplex (full-duplex|half-duplex)
Vcc interface mode chinese
clear
end
english
exit
help
history
ip address A.B.C.D A.B.C.D
ip address A.B.C.D
no virtual-channel
quit
show interface
show interface vcc
virtual-channel <1-63>
Remote interface converter
configuration mode. chinese
clear
device-name NAMESTRING
device-type (rc952fee1|rc952fxe1)
end
english
exit
help
history
interface e1
interface fx-eth
list
quit
reset
show device
show interface e1
show interface fx-eth
Remote interface converter
device mode. chinese
clear
device-name NAMESTRING
device-type (rc952fee1|rc952fxe1|rc951fee1|rc953fe8e1|rc953fx8e1|rc953fe8e1bl
|rc953fx8e1bl|rc953fe4e1|rc953fx4e1|rc954fe4e1|rc954fx4e1)
end
english
exit
help
history

www.raisecom.com User Manual
9
interface e1
interface (eth|fx-eth)
list
[ no] err-auto-shutdown
quit
reset
show interface e1
show interface (eth|fx-eth)
Remote interface converter
E1 interface configuration
mode.
chinese
clear
clock-mode (master|slave)
crc-auto (enable|disable)
end
english
exit
help
history
interface e1
interface (eth|fx-eth)
list
quit
show interface [e1]
show interface (eth|fx-eth)
Remote interface converter
Eth interface configuration
mode.
autonegotiate
chinese
clear
end
english
exit
fault-pass (enable|disable)
flow-control (on|off)
help
history
list
no autonegotiate
no shutdown
quit
show interface [eth]
shutdown
speed {10|100} duplex {full-duplex|half-duplex}