RAMTONS RM/288 User manual

READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2015
Attention: Pictures in the IM are for reference only.
OWNER’S MANUAL
16" Wall Fan
MODEL: RM/288
145x210mm FW40-6HR Black 365 20150613
Easy living

1
Read Rules for Safe Operation and Instructions Carefully.
CAUTION
1. If the supply cord is damaged, it must be replaced by manufacturer
or its service agent or a similarly qualified person in order to avoid
a hazard.
2. To protect against the risk of electrical shock, do not immerse the
unit, cord or plug in water or other liquid.
3. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in
a safe way and understand the hazards involved. Children shall
not play with the appliance. Cleaning and user maintenance shall
not be made by children without supervision.
4. When the appliance is not in use and before cleaning, unplug the
appliance from the outlet.
5. Keep electrical appliances out of reach from Children or infirm
persons. Do not let them use the appliances without supervision.
6. When the fan was assembled, the rotor blade guard shall not be
taken off anymore
- Prior cleaning unplug the fan.
- The rotor guard shall not be dissembled/opened to clean the
rotor blades.
- Wipe the fan enclosure and rotor blade guard with a slightly
damp cloth.
7. The fan is to be installed so that the blades are more than 2.3m
above the floor.
WARNING
1. Never insert fingers, pencils, or any other object through the grille when fan is
running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid overturning.
4. DO NOT use fan in window, rain may create electrical hazard.
5. Household use only.
RULES FOR SAFE OPERATION

PART FIGURE
2
Note: All the pictures in this manual are for explanation purpose only. Any discrepancy between
the real object and the illustration in the drawing shall be subject to the real subject.
MOUNTING ON THE WALL
The fan should be installed on a solid wooden or
pillar which stands vertically to the floor.
Caution: To prevent the fan from falling off, do not
install it on walls less then 10 cm thick or made of materials that are easily damaged.
INSTALLATION INSTRUCTIONS
1.Front grill
2.Spinner
3.Circlip
4.Blade
5.Plastic nut
6.Rear grill
7.Motor shaft
8.Motor
GUARD & FAN BLADE ASSEMBLY
1. Unscrew the spinner clockwise (or take the spinner out from the bag) and the
plastic nut counter clockwise to remove both of them. Fix the rear guard to the
motor then tighten the plastic nut again. (Fig. 1)
2. Insert the blade into shaft, and make sure the rotor shaft pin is fitted into groove
of the blade. Turn the spinner counter clockwise to tighten the blade. (Fig. 2)
3. Fix the front guard and the rear guard with circlip and then tighten the fan guard
locking screw and nut. (Fig. 3)
Fig.1 Fig.2 Fig.3

“ ” ON/OFF KEY
The key is for switching on the fan .The fan will be started at
low speed.Press this key again the fan will be swithed off.
“ ” TIMER KEY
When this key is touched repeatedly or kept in pressed state,
the time to be set for air delivery increased step by step of each
0.5 hour and sums to 7.5 hours in 15 steps.
For instance, if the fan operation is required to be set for 5.5 hours, this key must be
touched repeatedly so that the pilot lamps for 0.5, 1 and 4 hours lighten together. It
means that the set time is 0.5+ 1+ 4= 5.5 hours.
The time setting indicated by the pilot lamp will decrease gradually by a unit of 0.5
hour.
Don’t press the TIMER key when the fan is required to operate continuously. At the
moment all pilot lamps don’t light.
“ ” SPEED KEY
After the fan has started, this key serves as a speed selector in the sequence from
“low-medium-high-low” when this key being touched repeated or continuously.
“ ” OSC KEY
After the fan is started, press this key to oscillate the fan, and stop the oscillation at
desired direction by pressing again. By rotating the fan head by hand, you can get
wider oscillation angle.
3
1.Installing the mounting bracket
Fix the supplied mounting bracket firmly to the wall using the
two screws.
NOTE: The bracket should be pceiling and at least 30 cm from
adjoining wall.
2.Installing the stand
Mount the stand on the bracket by inserting the
bracket catch into the slot on the stand.
TO ADJUST THE WIND DIRECTION
Push the guard lightly to the desired up or down direction.
Fig.4
OPERATING INSTRUCTIONS
I. REMOTE CONTROLLER OPERATION (Fig.4)

4
To adjust the air flow upward or downward, push the guards lightly to the desired
direction.
II. Tilt Adjustment
“ ” MODE KEY
Press this key to select mode. This key is a selector key for wind type. The wind type
changes in the sequence from NORMAL---NATURAL---SLEEP---NORMAL---
NATURAL wind when this key being touched repeatedly or kept in.
The features of 3 wind types are as follows:
NORMAL WIND:
The fan delivers air constantly with high, medium or low speed set by the SPEED key.
NATURAL WIND:
The fan delivers air according to the program preset in advance and simulating the
natural wind. The wind variations from strong to weak or vice-versa make man a
fresh and comfortable as like as an enjoyment in Mother nature.
SLEEP WIND:
The wind weakens step by step during the preset time until stop. And then the fan
switches automatically off so that man can drop asleep.
1. Press dawn on the battery compartment cover
and slide it out.
2. Insert the batteries, making sure that the positive
terminals are facing the proper way.
3. Replace the cover.
BATTERIES INSTRUCTIONS
(not included)
1. “Do not dispose of batteries in fire, batteries may
explode or leak.”
2. -Do not mix old and new batteries.
3. -Do not mix alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium) batteries.
BATTERY WARNING AS BELOW

The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified
service personnel if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.
MAINTENANCE INSTRUCTION
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
Thoroughly remove soap film with dry cloth.
DISPOSAL：Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities. Contact your
local government for information regarding the collection systems
available. If electrical appliances are disposed of in landfills or dumps, hazardous
substances can leak into the groundwater and get into the food chain, damaging
your health and well-being.
5
The windings of the motor have a thermal-fuse that burns out and the fan switches
off and temperature of the motor is no longer going up so that plastic parts of the fan
don’t subject to deformation so far so to be burned by the overheat if the motor is
overheat for any unexpected reason.
OVERHEAT PROTECTION OF THE MOTOR
Point the remote controller at the receptor on body of the fan and press the desired
button. The remote controller will work at distances of up to roughly five meters and
the angle of 30 degree included between right and left from the receptor.
The batteries must be removed from the remote controller before it is scrapped and
that they are disposed of safely.
HOW TO USE THE REMOTE CONTROLLER CORRECTLY