Rand McNally ME-01 User manual

1
2
3
7
4
ITEM NO. PART NO. DESCRIPTION QTY
1 VPP-77329 SD CARD - OPTION C 1
2 VPP-SD_UPDATE SD CARD 1 AND SD CARD 2 MEDIA PLAYER SOFTWARE UPDATE 1
3 VPP-77613 POWERED OVERDRYVE 7C POD ASSEMBLY 1
4 VPP-77617 BUTTON GRAPHIC - OPTION C 1
5 VPP-77624 DUMMY OVERDRYVE TND 740 POD ASSEMBLY 1
6 VPP-77618 MONITOR HOUSING GRAPHIC - OPTION C 1
7 N/A FLAT CARTON (prepaid return shipping label applied) AND TAPE 1
Option C
VPP-P77329
OverDryve
Refresh
7.9.17
DO NOT DISCARD BUBBLE WRAP
DO NOT DISCARD FLAT RETURN SHIPPING CARTON
SET ITEMS ASIDE FOR LATER REUSE
.
SD Card
Option C
envelope
envelope
SD Card 1
Tape
Flat Carton
(labels already applied)
SD Card 2
6
5
VPP-SD_UPDATE
DO NOT DISCARD
SD CARD
OPTION C
BEST BUY
RETURNS
BEST BUY
RETURNS
Powered OverDyve 7C
pod assembly
Dummy OverDyve
TND-740 pod assembly
Button Graphic
Option - C
Monitor Housing Graphic
Option - C
Rand McNally OverDryve Display ME-01 - Refresh Option C
19607-1 P77343 7-9-17
FOR SUPPORT, CALL OR EMAIL

A
.
DISPLAY MUST BE REMOVED FROM GONDOLA
On underside of display, on the left
and right, remove safety brackets
securing display to gondola by
removing screw, then place brackets
and screws aside.
BRemove display from gondola by lifting it up then
pull it forward. Place display on shelf (not
shown), leaving it plugged in and powered.
CRemove back panel by removing screws to
expose the media player. Blue light on media
player confirms it is powered.
DSwitch media player power to OFF. Remove
existing SD card by pushing it down and then
pulling it out. Discard this SD card.
REMOVING DISPLAY FROM GONDOLA --- TWO PEOPLE REQUIRED
media
player
media player
power switch
SD card
1
TWO PEOPLE REQUIRED
Rand McNally OverDryve Display ME-01 - Refresh Option C
1 of 15 19607-1 P77343 7-9-17

APut SD card 1 in the media player and push it until it
clicks. Then switch media player power switch to ON.
BMonitor screen will be black with a progress bar that will
progress until CARD OK is shown (~5 minutes). Speakers
may make a popping noise during this process. After
CARD OK is shown, screen will show No Signal, meaning
the update is complete.
CTurn media player power switch to OFF and remove SD card 1.
UPDATING MEDIA PLAYER SOFTWARE --- SD CARD 1
DO NOT INTERRUPT POWER
DURING THE UPDATE OR MEDIA
PLAYER MAY BECOME UNUSABLE
power switch SD card
update will
take ~5 mins
CARD OK
screen
No SIgnal
screen =
update
complete
Option C
VPP-P77329
OverDryve
Refresh
7.9.17
2
1
2
3
SD Card
Option C
SD Card 1 SD Card 2
2 of 15
Rand McNally OverDryve Display ME-01 - Refresh Option C
19607-1 P77343 7-9-17

APut SD card 2 in the media player and push it until it
clicks. Then switch media player power switch to ON.
BMonitor screen will change several times as shown below.
NOTE: update will take ~3 minutes.
DO NOT INTERRUPT POWER
DURING THE UPDATE OR MEDIA
PLAYER MAY BECOME UNUSABLE
power switch SD card POWER ON
LOADING...
Make yourself at home
updating APK please wait...
Complete, please turn off power...
Power OFF media player within 5 minutes
after seeing this screen
3
14
5
6
2
3
UPDATING MEDIA PLAYER SOFTWARE --- SD CARD 2
Option C
VPP-P77329
OverDryve
Refresh
7.9.17
CTurn media player power switch to OFF and remove SD card 2.
SD Card
Option C
SD Card 1 SD Card 2
3 of 15
Rand McNally OverDryve Display ME-01 - Refresh Option C
19607-1 P77343 7-9-17

BOn front of display, remove 5 screws from product
securing bracket, then lift off bracket and set bracket and
screws away from display for later reuse.
AOn back of display, remove ONLY the cable tie holding
cigarette lighter adapter into power connector (highlighted
in red). Then remove the cigarette lighter adapter from
the power connector. Leave it until later step.
5X
screws
remove this
cable tie
leave this
cable tie
unplug cigarette lighter adapter
from power connector remove
product
securing
bracket
product
securing
bracket
REMOVING EXISTING OVERDRYVE 7 POD ASSEMBLY
4
Existing OverDryve 7
pod assembly
19607-1 P77343 7-9-17
Rand McNally OverDryve Display ME-01 - Refresh Option C
4 of 15

DRemove the cigarette lighter adapter from the
display as shown.
ERemove OverDryve 7 pod and set aside for later step.
CRemove 2 screws to remove OverDryve 7 pod, then
place it behind adjacent pods as shown below.
2X
screws
place behind
adjacent pods
route
adapter out
through
hole
remove
OverDryve 7
pod and set
aside for
later step
remove
cigarette
lighter
adapter
19607-1 P77343 7-9-17
5 of 15
Rand McNally OverDryve Display ME-01 - Refresh Option C

APlace new OverDryve 7C pod assembly behind
adjacent pods as shown in the picture.
BRoute the cigarette lighter adapter through the
display as shown.
cigarette
lighter
adapter
out hole route
adapter in
through
hole
COn back of display, plug in OverDryve 7C cigarette lighter
adapter into power connector. Ensure power connection
by red light on cigarette lighter adapter.
red light
when powered
plug cigarette lighter adapter
into power connector
INSTALLING NEW OVERDRYVE 7C POD ASSEMBLY
5
New OverDryve 7C
pod assembly
19607-1 P77343 7-9-17
6 of 15
Rand McNally OverDryve Display ME-01 - Refresh Option C

DPlace new OverDryve 7C pod so outermost screw
can easily be attached through hole on pod, then
make sure wire is not being smashed before snug
tightening the screw. Attach other screw and before
final tightening, ensure wire is not being smashed
by pod.
make sure
wires are not
smashed
make sure
wires are not
smashed
19607-1 P77343 7-9-17
Rand McNally OverDryve Display ME-01 - Refresh Option C
7 of 15

REMOVING EXISTING DASH MOUNT POD ASSEMBLY
6
existing dash
mount pod assembly
BRemove 2 screws located behind dash mount pod to
disengage pod from the display. Lay pod on top surface
of display until later step.
ADash mount pad is on right side of display (shown
highlighted in yellow).
2X
screws
lay pod down
until later step
19607-1 P77343 7-9-17
8 of 15
Rand McNally OverDryve Display ME-01 - Refresh Option C

C
view with bottom panel removed
Leaving display plugged in and powered, lift display off
shelf and place on floor. Tilt display and gently place it
on its back. NOTE: take care that loose dash mount pod
is handled gently when tilting.
DRemove screws from the bottom panel to expose button wiring. Place bottom panel and screws aside for later reuse.
TWO PEOPLE REQUIRED
(1 person shown for clarity)
19607-1 P77343 7-9-17
9 of 15
Rand McNally OverDryve Display ME-01 - Refresh Option C