Rane DRZH User manual

1
DRZH
User Guide
English (3–8
)
Appendix
English (34)

User Guide (English)
Introduction
Thank you for purchasing the DRZH. At Rane, performance and reliability
mean as much to us as they do to you. That’s why we design our equipment
with only one thing in mind—to make your performance the best it can be.
Box Contents
DRZH
Mounting Screws
User Guide
Safety & Warranty Manual
Support
For the latest information about this product (documentation, technical
specifications, system requirements, compatibility information, etc.) and
product registration, visit rane.com.
For additional product support, visit rane.com/support.

3
Setup
Items not listed under Introduction >Box Contents are sold separately.
Note: Use a shielded Ethernet cable (Cat5e or Cat6) to connect the RJ45
port on the rear panel to the main audio processing unit (e.g., a Rane
Zonetech, HAL3s, or Terminal 1010x).
Zone
Amplifier
Audio
Inputs
Zone
1
Zone
2
Zone
3
Zone
4
Zonetech

Installation
DRZH can be mounted in a standard 1-gang US electrical box:
1. Run a shielded Ethernet cable (Cat5e or Cat6) from the audio
processing unit to the electrical box, and then connect it to the RJ45
port on DRZH's rear panel. DRZH can be located up to 300 meters
(984 feet) from the processing unit.
2. Use the included screws to secure the DRZH rear housing to the
electrical box and wall.
Note: A minimum 1/4" diameter by 1" depth (6.35 x 25.4 mm) pilot
hole is required for the included wall anchors.
3. Make sure the knob has been removed, then place the faceplate over
the DRZH housing and reattach the knob.
1-gang US
Electrical Box
DRZH Rear
Housing
DRZH
Faceplate
Knob
Screws

5
Features
Front
Panel
1
2
Rear
Panel
3
1. Display: This screen shows the setting that the knob on DRZH is
currently adjusting. Push the knob to select the next setting.
2. Knob: Turn this knob to adjust the setting currently shown in the
display. Push the knob to select the next setting.
3. RJ-45 Port: Use a shielded Ethernet cable (Cat5e or Cat6) to connect
this port to the main audio processing unit (e.g., a Rane Zonetech,
HAL3s, or Terminal 1010x).

Operation
By default, the display on DRZH will show the volume setting for the
current room (zone): Volume.
To adjust the volume, turn the knob.
You can access and adjust other settings, as well, depending on the
system DRZH is connected to.
To select another setting, push the knob. The current setting will be
shown in the display.
The adjust the current setting, turn the knob.

7
Troubleshooting
If you encounter a problem, try doing these things first:
•Make sure all cables and other connected devices are properly and
securely connected.
•Make sure you are using DRZH as described in this user guide.
•Make sure your other devices or media are working properly.
•If you believe DRZH is not working properly, check the following for
your problem and solution.
Problem: Power does not turn on.
Solution: Make sure DRZH’s RJ45 port is properly connected to and
located within 300 meters (984 feet) from your audio processing unit.
Please see: Setup

Appendix (English)
Technical Specifications
Display
1.1” x 0.6” / 26.7 x 15.5 mm (width x height)
1.2” / 30.9 mm (diagonal)
128 x 64 pixel resolution
Monochrome, white on black
Connectors
(1) Ethernet/RJ45 port
Power
Connection: Ethernet/RJ45 port
Voltage: 24 V
Consumption: 1.2 W
Dimensions
(width x depth x height)
3.0” x 2.0” x 4.7”
75 x 50 x 120 mm
Weight
0.3 lb.
150 g
Specifications are subject to change without notice.
Trademarks & Licenses

9
Rane is a trademark of inMusic Brands, Inc., registered in the U.S. and
other countries. All other product names, company names, trademarks, or
trade names are those of their respective owners.

rane.com
Manual Version 1.0