Ranger design 6255 User manual

INSTALLATION GUIDE
6255 BUCKET SEAT SET
Ford Transit ( 2015-2016 )

For technical support, contact us at 1-800-565-5321 6255 Installation Guide |REV. A1 | Page 2
Phase 1 - Preparation
Phase 2 - Installation
q 1.1 Remove Headrests.
q 2.1 Install Seat Back Cover.
q 2.2 Install Seat Bottom Cover.
q 2.3 Install Headrest Cover.
QUICK START GUIDE
BILL OF MATERIALS
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Item No. Description Qty.
62-553 Seat Back Cover Passenger Side 1
62-551 Seat Bottom Cover Passenger Side 1
62-554 Headrest Cover Passenger Side 1
62-552 Seat Back Cover Driver Side 1
62-553 Seat Bottom Cover Driver Side 1
62-554 Headrest Cover Driver Side 1

For technical support, contact us at 1-800-565-5321 6255 Installation Guide |REV. A1 | Page 3
PHASE 1 – PREPARATION
1.1 REMOVING
PHASE 2 – INSTALLATION
2.1 SEAT COVER INSTALLATION
q1.1 Remove Headrests.
q Pull headrests out of the seats
by pressing the tabs at the base of the headreasts.
q2.1 Install Seat Back Cover.
q Ensure the tag inside the cover corresponds with the seat you are working on.
Each cover will have a Driver or Passenger tag.
q Undo elasc strap holding seat back ap from under seat boom (Black strap with white clip).
q Tip seat back ap up and tuck inside seat cover as you pull it down.
q Turn seat cover 3/4 of the way inside out.
q Pull seat back cover into posion, making sure that the holes in the cover align
with the holes in the seat back.
q Stretch the cover over the headrest holes.
q Connue pulling the cover down the seat back, turning it right side out as you go.
q Push ap from front of cover between seat back and seat boom, out the back of the seat .
q Double the end of the ap over to prevent the “hook” Velcro
from scking to the factory upholstery.
q Pull the ap ght and aach to the Velcro on the back of the seat.
q Fasten ap under the armrest.

For technical support, contact us at 1-800-565-5321 6255 Installation Guide |REV. A1 | Page 4
q2.2 Install Seat Bottom Cover.
UNDER
qEnsure the tag inside the cover corresponds
with the seat you are working on.
Each cover will have a Driver or Passenger tag.
qPlace seat boom cover over boom of seat.
qPush ap on top of cover between seat back
and seat boom.
qTuck sides of cover behind plasc trim.
qPush strings between seat boom and plasc trim.
They will go through where the seat back and
boom meet. Strings must go UNDER round bar that runs
through seat boom.
qPull strings behind seat and pull ght.
qTie a loop in one string, close to the edge of the
seat.
qRun the other string through the loop and pull as ght as
possible. This is what keeps your seat boom from shiing.
qPull boom aps from front of seat boom and
aach to top ap.
qFlaps MUST run OVER bars and brackets under seat.
Seat cover bottom ap, running OVER all bars,

For technical support, contact us at 1-800-565-5321 6255 Installation Guide |REV. A1 | Page 5
q2.3 Install Headrest Covers.
qPut headrests back on seats.
qPress tabs at base of headrest and push headrest into seat back.
qPull headrest cover over headrest with “hook” Velcro on
the back and “loop” Velcro on the front.
qPull front ap over back ap and fasten.

For technical support, contact us at 1-800-565-5321 6255 Installation Guide |REV. A1 | Page 6
“Congratulations, you have successfully installed your
Seat Cover Set!
Thank you for doing business with us.”