Raven RS1 User manual

Manual No. 016-5033-152 Rev A1. EC31824 08/18 1
MASSEY FERGUSON 8600/8700 AND
CHALLENGER MT6X5C/D/E STEER READY RAVEN
RS1™ ISO GUIDANCE AND STEERING
INSTALLATION GUIDE
This quick guide provides installation instructions of RS1 on a steer ready Massey Ferguson 8600/8700 tractor. For
calibration and operation information, refer to the Operation Manual (P/N 016-4010-001) included with the kit.
The RS1 is an all-in-one unit that provides GPS, guidance, and optional cellular connectivity.
INSTALLATION DIAGRAM
The image below provides a basic overview of the installation of the RS1. Refer to the next sections for detailed
installation information.

2 Massey Ferguson 8600/8700 and Challenger MT6X5C/D/E Steer Ready Raven RS1™ ISO Guidance and
FIGURE 1. Massey Ferguson Series Installation Diagram

Manual No. 016-5033-152 Rev A1. EC31824 08/18 3
RS1 UNIT INSTALLATION
For RS1 to operate, the RS1 unit must be mounted on the cab roof. To install the unit:
1. Assemble the latch, plug, rubber washer, and latch nut through the latch hole on the RS1 mounting plate.
FIGURE 2. Latch Assembly
2. Using the four 1/4” - 20 x 1/2” flat head machine screws provided, install the RS1 mounting bracket to the
bottom of the RS1 unit.
FIGURE 3. RS1 Mounted to Bracket
3. With the front of the RS1 (sloped edge) towards the front of the machine, place the installation tab of the RS1
mounting bracket in the installation tab slot.
RS1 Mounting Plate
Latch
Rubber Washer
Latch Hole
Plug
Latch Nut
Bottom of RS1 Unit
RS1 Mounting
Bracket
RS1 Mounting Bolts

4 Massey Ferguson 8600/8700 and Challenger MT6X5C/D/E Steer Ready Raven RS1™ ISO Guidance and
FIGURE 4. Installation Tab
4. Connect the black 12-pin Deutsch connector on the RS1 cable (P/N 115-4010-006) to the back of the RS1 unit.
FIGURE 5. Cabling Connection on RS1 Unit
5. Place the RS1 bracket on the existing mounting plate with the latch plug inside the latch hole.
6. Press down on the latch handle until it locks to secure the RS1 assembly in place.
FIGURE 6. Installed RS1 Unit
NOTE: The latch may need to be adjusted to provide proper compression. To do this, tighten the nut on the
bottom of the latch.
7. If applicable, connect the cellular antenna to the back of the RS1 unit and secure the antenna to the roof
bracket using the magnet attached to the antenna.
Installation Tab
Slot Latch Hole
Installation Tab
Connect
Here
Cellular
Antenna
RS1 Unit
Latch
Mounting
Bracket

Manual No. 016-5033-152 Rev A1. EC31824 08/18 5
8. Connect the 12-pin Deutsch connector to the mating connector on the back of the RS1 unit.
9. Feed other end of the RS1 cable towards the mating connector on the machine’s roof.
10. Remove the cap off the mating roof connector.
11. Connect the 12-pin Amphenol connector to the mating roof connector.
FIGURE 7. Completed Cable Connection
12. Connect the RS1 Breakout Cable (P/N 115-4010-052) to the 6-pin DTM connector on the RS1 Roof Adapter
Cable.
13. Route the other end of the cable down the right-rear corner post and into the cab through the grommet at the
bottom of the rear window.
14. Connect the engage foot switch (P/N 063-0172-470) to the 2-pin DT connector.
OPERATION
Refer to the RS1 Calibration and Operation Manual (P/N 016-4010-001) for instructions on configuring, calibrating,
and operating RS1. Please note the location of the master switch on the machine as it is needed for operation.
FIGURE 8. Master Switch and Resume Foot Switch
Master Switch Resume Foot Switch

6 Massey Ferguson 8600/8700 and Challenger MT6X5C/D/E Steer Ready Raven RS1™ ISO Guidance and