Raven MTi User manual

RAVEN&MTI&&PRO&TOOLS&USER&MANUAL&&&&&
1!
MTi
PRO TOOLS USER GUIDE & BATCH COMMAND SYSTEM MANUAL
RAVEN Version 2.5.0
Updated 3/9/2015 - REV-B

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
2!
Updated 3/9/2015
Contents
IMPORTANT SAFETY NOTES BEFORE YOU START ..............................................................3!
WARRANTY INFORMATION ................................................................................................6!
MAINTENANCE AND CARE..................................................................................................8!
Cleaning the RAVEN MTi!.......................................................................................................................................!8!
Revitalizing the RAVEN MTi Glass!........................................................................................................................!9!
GETTING STARTED .......................................................................................................... 13!
System Requirements!..........................................................................................................................................!13!
RAVEN MTi Dimensions!........................................................................................................................................!14!
Attaching RAVEN MTi To Its Stand!....................................................................................................................!15!
Connecting RAVEN MTi to your computer!....................................................................................................!18!
Software Installation and Touch Calibration!...................................................................................................!20!
Connecting RAVEN MTi to Pro Tools!.................................................................................................................!25!
Launching RAVEN MTi Software!.........................................................................................................................!27!
REVIEW OF TOUCH CALIBRATION ...................................................................................27!
INSTALLING RAVEN MTI FOR PRO TOOLS ........................................................................35!
Setting Up & Aligning Pro Tools With RAVEN!..................................................................................................!35!
RAVEN MTI PRO TOOLS SOFTWARE FEATURES................................................................39!
The RAVEN Mixer!..................................................................................................................................................!39!
RAVEN Channel Strip!...........................................................................................................................................!39!
Automation Modes!...............................................................................................................................................!41!
Icons!.......................................................................................................................................................................!41!
RAVEN Toolbar!.....................................................................................................................................................!45!
RAVEN Settings!.....................................................................................................................................................!62!
Saving a Pro Tools Session!..................................................................................................................................!67!
Saving a RAVEN Session!.......................................................................................................................................!67!
Restoring to Factory Default!..............................................................................................................................!69!
Edit Window!..........................................................................................................................................................!69!
WORKING WITH PRO TOOLS PLUGINS ..........................................................................70!
Loading Plugins:!...................................................................................................................................................!70!
Controlling Plugins:!.............................................................................................................................................!72!
Closing a Plugin:!...................................................................................................................................................!72!
BATCH&COMMAND&SYSTEM&FOR&PRO&TOOLS&10/11 ............................................................73!

RAVEN&MTI&USER&MANUAL&&&&&
3!
Important Safety Notes Before You Start
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within your RAVEN MTi.
This symbol indicates there are important operating and maintenance instructions
in the literature accompanying your RAVEN MTi.
1. Read these instructions
2. Keep these instructions
3. Regard all warnings
4. Follow all instructions
5. Do not use this apparatus near water
6. Do not block any ventilation openings. Install in accordance to the
manufacturer’s instructions
7. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
8. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
device.
9. Only use attachments/ accessories specified by the manufacturer.

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
4!
10. Unplug this apparatus during lightning storms or when unused for long
periods of time.
11. Do not press strongly on the panel with a hand or sharp object such
as a pencil, pen, or nail.
12. Do not stick metal objects or conductive material in the device,
power chord, or power inlet.
13. Make sure you connect the earth ground wire to prevent electric
shock. A cable with a three-pronged grounded AC Plug must be connected
to a three-pronged AC outlet.
Power Source
Operate your RAVEN MTi only from the power source included.
Power supply manufacturer: Lite-On Technology
Model: PA-1041-71
Electrical rating: INPUT 100-240 VAC, 50/60 Hz, 1.2A, OUTPUT: 12VDC, 3.33A
Moving
Make sure the product is turned off, unplugged, and all cables have been removed. It
will take a minimum of two people to move your RAVEN MTi, although three are
recommended.
Servicing
Servicing of the RAVEN MTi is to be done by qualified service personnel only. To
reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Damage Requiring Service
Unplug the device from the power outlet and refer servicing to qualified service
personnel under the following conditions:
•When power supply is damaged
•If liquid has been spilled or objects have fallen into the RAVEN MTi.
•If your RAVEN MTi has been exposed to rain or water.
•If your RAVEN MTi has been dropped or damaged in any way.
•When your RAVEN MTi exhibits a distinct change in performance.

RAVEN&MTI&USER&MANUAL&&&&&
5!
Important Note About DVI Cables & Display
As in many studios, your computer may be located in a room far away from your
console. For DVI cable lengths over 15ft, a DVI signal booster is required. This will
ensure the video signal reaches the display with no signal degradation.
Additionally, when switching sources between DVI and HDMI for the display, you must
press the center button of the remote, or the source button on the OSD board behind
the meter access panel.
You must wait a full 6 seconds before the source will change.
Also there is no RGB input for the MTi. Although it will show as a source, it should be
ignored. It will take around 14 seconds to switch to the RGB source, just be patient
and move on to DVI when the RGB source is selected.

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
6!
Warranty Information
Hardware Limited Warranty
A. Limited Warranty
Slate Media Technology (SMT) warrants that its hardware will be free from defects in
materials and workmanship, for one (1) year after it has been acquired by the first
user when given normal, proper and intended usage. SMT will repair or replace
nonconforming product (or a component thereof) that is returned to SMT within the
warranty term at no charge.
This warranty applies to products purchased anywhere in the world. You may have
additional consumer rights under local laws. SMT will provide the minimum warranty
term required by applicable law.
B. Warranty Recipient
The limited warranty applies only to genuine SMT products when sold by an SMT
reseller, distributor or dealer.
C. Exclusions from Warranty
This warranty does not cover problems caused by your acts, the acts of others, or
events beyond SMT’s reasonable control.
SMT does not warrant that use of SMT products will be uninterrupted or error-free.
This limited warranty does not apply to expendable components and is void if the
product serial numbers have been removed. SMT has no obligation under this
warranty to repair or replace products damaged as a result of 1) normal wear and
tear, 2) improper or unauthorized use or repair, 3) customer fault or negligence, 4)
natural or manmade disaster, or 5) causes external to the products including, but not

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
7!
limited to, exposure to moisture, extreme temperatures, power outages, or other
customer site conditions.
D. Limitation on and Exclusion of Damages for Breach of Warranty
You may recover from SMT and its suppliers only direct damages up to the amount you
paid for the product.
You cannot recover for loss of present or prospective profits, data loss, business
damage, or any other consequential, special, indirect or incidental damages.
E. Warranty Procedures
For information regarding your warranty, please contact Slate Media Technology or
your local authorized reseller, distributor, or dealer. Product registration at
www.slatemt.com is required in order to process a warranty claim. You will be
required to provide proof-of-purchase to validate your claim.
Hardware may require return-to-factory, and customer is responsible for properly
packing and labeling and insuring any warranty returns for shipment to Slate Media
Technology. Customer is responsible for any damage or loss incurred due to improper
packaging or labeling. Customer is required to pay shipping/handling one way for
warranty product returns and applicable custom duties, V.A.T. and other associated
taxes and charges for international service.

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
8!
Maintenance and Care
Cleaning the RAVEN MTi
The RAVEN MTi ships with a Revitalizer spray that used a NanoGlide™ coating, which
protects the screen from oil, water, and dirt. The coating also strengthens the surface
of the glass making it scratch resistant and smooth to the touch.
IMPORTANT:
Do not use regular cleaning solutions on the RAVEN MTi.
Household sprays and cleaners will affect the touch glass coating, which can impact
performance. We recommend a simple microfiber cloth to clean the surface of the
glass.
If more intensive cleaning is required, use a lightly damp cloth. Make sure that the
cloth is not too wet; the coating will make the water bead and drip. As a precaution,
keep a dry cloth at the bottom of the screen to catch any runoff.
Do not allow moisture from liquids to accumulate on the screen when cleaning.
Accumulation of liquids can damage internal electrical devices. If a damp cloth
must be used, make sure to remove any excess water immediately after cleaning.
To clean RAVEN MTi’s exterior metal parts use a simple microfiber cloth. If deeper
cleaning is required, a non-abrasive cleaning solution can be used on the metal parts
only. Be sure to not spray cleaner on the RAVEN MTi directly, rather spray the
cleaner on to a cleaning cloth away from the RAVEN MTi, then use the dampened
cloth on the RAVEN MTi’s metal parts.
The high gloss lacquer finish on RAVEN MTi’s side panels can be damaged by some
cleaners. Use a gentle cleaning solution. Test in an inconspicuous area first.

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
9!
Revitalizing the RAVEN MTi Glass
The RAVEN MTi comes out of the box with a NanoGlide™ coating that repels oil,
water, and leaves the surface incredibly smooth to the touch.
After some use, it may be necessary to revitalize to bring the glass back to its original
slickness. We recommend using the revitalizing solution when you feel the glass has
substantially more friction than when you first started using your RAVEN MTi.
The coating process is very easy and can be done following the steps below. All you
need is a microfiber cloth and the supplied 4oz bottle of Revitalizer/Protector
solution.
IMPORTANT:
Apply the revitalizer solution in a well-ventilated area
NOTE:
The Revitalizer Solution is not a product of Slate Media Technology. Please read the
Revitalizer label for more information, precautions, and first aid instructions.

RAVEN&MTI&PRO&TOOLS&USER&MANUAL&&&&&
10!
1. Using a microfiber cloth, clean the RAVEN MTi screen to remove dust and
fingerprints.
2. Spray the revitalizer solution directly onto the RAVEN MTi glass. It should take
approximately six sprays to cover the glass completely.
IMPORTANT
Do not spray so much that the solution drips down the screen. Excess
moisture could damage the display and touch system. If you are unsure,
place a cloth at the bottom of the screen to catch any runoff.