Rawinternational FL1 User manual

nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
winternational
rawinternational
rawinternational
rawinternational
rawin
ational
rawinternational
rawinternational
rawinternational
rawin
winternational
rawinternational
rawinternational
rawin
ational
rawinternational
rawinternational
rawin
rawinternational
rawinternational
rawin
ational
rawinternational
rawin
rawinternational
rawin
rnational
rawin
rawin
nal
rawinternational
rawinternational
rawinte
nal
rawinternational
rawinternational
rawinternationa
nal
rawinternational
rawinternational
rawinternational
rawinte
nal
rawinternational
rawinternational
rawinternational
rawinternationa
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinte
nal
rawinternational
rawinternationa
nal
rawintern
nal
rawinternational
nal
ra
4. Security
Once the screen is safely suspended, please tighten the bolts on the bottom left and right of the bracket
using a screw driver (DO NOT OVER TIGHTEN) This engages the front plates to the wall mounting plates
to ensure the screen cannot be lifted from the wall (fig. 6).
FL1
INSTRUCTION
MANUAL
rawinternational
CONSULT AUTHORISED SERVICE PERSONNEL FOR
THE INSTALLATION OF THIS UNIT. INSTRUCTIONS
MUST BE FOLLOWED PRECISELY FOR SAFE AND
STABLE INSTALLATION. RAW INTERNATIONAL ARE
NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED
BY MISHANDLING OR IMPROPER INSTALLATION.
INSTALLATION (PLEASE READ CAREFULLY)
INSTALLATION OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY QUALIFIED
TECHNICIANS. INSTALL IN AN APPROPRIATE LOCATION ONLY AFTER CHECKING
WALL STRUCTURE AND DURABILITY FOR ACCIDENT PREVENTION. CONSULT A
QUALIFIED BUILDER IF IN ANY DOUBT AS TO STRUCTURAL INTEGRITY OF WALL.
List of components Spacers Penny Washer
M4x20mm x 4 M5x20mm x 4 M6x20m x 4 15x7.3x5 x 4 16x5.3x1.0 x 4
M4X45mm x 4 M5x45mm x 4 5mm hex key x 1 15x7.3x10 x 4
M4X55mm x 4 M5x55mm 4 M8x20mm x 4 15x7.3x30 x 4 Standard Washer
3mm hex key x 1 4mm hex key x 1 6mm hex key x 1 15x7.3x40 x 4 16x8.3x1.0 x 4
bracket
screw driver
screw driver
Fig. 4 Fig. 5
screen
Fig. 6

nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
winternational
rawinternational
rawinternational
rawinternational
rawin
ational
rawinternational
rawinternational
rawinternational
rawin
winternational
rawinternational
rawinternational
rawin
ational
rawinternational
rawinternational
rawin
rawinternational
rawinternational
rawin
ational
rawinternational
rawin
rawinternational
rawin
rnational
rawin
rawin
nal
rawinternational
rawinternational
rawinte
nal
rawinternational
rawinternational
rawinternationa
nal
rawinternational
rawinternational
rawinternational
rawinte
nal
rawinternational
rawinternational
rawinternational
rawinternationa
nal
rawinternational
rawinternational
rawinternational
rawinternational
rawin
nal
rawinternational
rawinte
nal
rawinternational
rawinternationa
nal
rawintern
nal
rawinternational
nal
ra
1. Mounting wall plate
Remove security screw from bottom of bracket
and detach front plate (fig. 2b). Mount wall plate
(fig. 1) on wall in desired position using screws/
bolts suitable to construction of the wall. (If in any
doubt please consult a qualified builder). Attach
screws/bolts through as many fixing as possible.
There are a total of 22 fixing holes on the back
plate, however the minimum amount of fixings
that Raw International recommend is six. (If in any
doubt as to strength of fixings please consult a
qualified builder.)
It is important that the front plates are fixed
as centrally as possible to the screen. To help
achieve this, there is a 2mm hole off centre of
each of the front plates. Line this hole up so it
is equal distance between the top and bottom
fixings on the screen (fig. 2). Once it is lined up,
the nearest fixing hole on the front plates to the
top fixing on the screen are the ones that should
be fixed first (fig. 3) using appropriate screws/
washers/isolators/spacers. Please use an allen
key to tighten all four screws. Only use isolators if
back of screen is not flush with the front plates.
Ensure front plates are situated in a centralised
position, tighten the screws on the bottom of the
front plates (fig. 4 overleaf) using a screw driver.
3. Engaging the screen with the wall
Lift the screen (minimum two) people with front
plates attached so that the bars engage with the
angled slots on the wall mounting plates (fig. 5
overleaf). The screen is now safely suspended.
steel washer
nylon isolator
front plates
screen
steel fixings
Fig. 3
2. Attaching front plates to the
plasma screen
Place the screen face down on soft cloth (to
prevent damage) on a flat surface (fig. 2). The
fixings you use are dependent on the make and
model of your screen. There are different sets of
fixings supplied with the bracket. Only ONE set of
fixings will be required. In order to ascertain which
set of fixings will be required, screw fixings in the
back of the screen before attempting to attach
front plates. Only ONE set of fixings will be of the
correct diameter for your screen.
Fig. 1
Mounting holes/slots
Fig. 2
security
screw
2mm
hole
screen
equal distance to 2mm hole
fixings holes on back of screen