Raycus RFL-P70Q User manual

编号
RFL-P70Q～P100Q
密级
阶段标记
页数 9
名称
RFL-P70Q～P100Q
脉冲光纤激光器英文使用说明书
会签
单位
第二事业部
编写
李科
校对
朱军
审核
施建宏
标审
李其军
批准
黄保
武汉锐科光纤激光技术股份有限公司

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
Ytterbium Pulsed Fiber Laser
User’s Guide
RFL-P70Q～P100Q
Wuhan Raycus Fiber Laser Technologies Co., Ltd.,2018
Proprietary information. All rights reserved
Issued 19 October 2018

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
Safety Information
Please read this instruction carefully and familiarize yourself with the information we have
provided before you use the product. In this brochure, important operation procedures, safety and
other information are provided for you and all future users. In order to ensure operating safely
and optimal performance of the product, please do according to following warnings, cautions and
other information.
Raycus pulsed fiber laser is classified as a high power Class IV laser device. Before supplying
the power to the device, please make sure that the correct voltage of 24VDC power source is
connected and the anode and cathode are right. Failure to connect power source correctly will
cause damage to the device.
The device emits invisible 1060~1085nm wavelength light with average power 70W～100W.
Do not expose your eyes or skin to the radiation of the laser.
Do not take apart the device, because there are no replaceable accessories available for users
to use. Any maintenance can only be proceeded in Raycus.
Do not look into the light output end directly. Use appropriate laser safety eyewear when
operating the device.
Safety labels and locations
The two labels above are located on the top of the cover of the device, representing laser
radicalization.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
Content
1. Description.............................................................................................1
1.1. Product description........................................................................................................1
1.2. Actual configuration list ................................................................................................1
1.3. Environmental requirements and cautions.....................................................................1
1.4. Specifications.................................................................................................................2
2. Mounting................................................................................................3
2.1 Mounting dimensions ....................................................................................................3
2.2 Method of installation....................................................................................................3
3. Control Interface...................................................................................5
4. Operation Regulations..........................................................................8
4.1 Pre-inspection ................................................................................................................8
4.2 Operation procedures.....................................................................................................8
4.3 Cautions.........................................................................................................................8
5. Instructions for warranty, return and maintenance..........................9
5.1 General warranty ...........................................................................................................9
5.2 Limitations of warranty .................................................................................................9
5.3 Service and repairs.........................................................................................................9

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
1/ 9
1. Description
1.1. Product description
Raycus pulsed laser is an ideal high power laser source with high speed and high efficiency.
It is specially designed for industrial laser making system and other applications.
Compared with traditional lasers, pulsed laser has some unique advantages in increasing the
conversion efficiency of the pump light 10 times higher. Its low power consumption and
automotive design make it appropriate for operating both in and outside the lab. Besides, it is
exquisite and convenient for its independence in placement, free time in using and facility in
connecting to equipment directly.
The device can emit 1060~1085nm wavelength pulsed light under the control of industrial
laser’s standard interface driven by 24VDC power source.
1.2. Actual configuration list
Table 1. Configuration list
Items
Quantity
Remark
Fiber Laser module
1
1.3. Environmental requirements and cautions
Pulsed laser should be driven by 24VDC±1V power source.
1) Caution: Make sure the corresponding wires of the device are properly grounded.
2) All the maintenance to the device should only be done by Raycus, because there is no
replacement or accessory provided with the device. Please do not try to damage the labels or
open the cover in order to prevent against electric shock, or the warranty will be invalid.
3) The output head of the product is connected with an optical cable. Please be careful handling
the output head. Avoid dirt and any other contaminations. Please use the specialized lens
paper when cleaning the lens. Please lid the laser with protective cover of the light isolator to
be against dirt only when the laser is not installed in the device or not in working.
4) If the operating the device fails to follow this instruction, the protective function will be
weakened. Therefore, it should be used under normal conditions.
5) Do not install the collimating device into the output head when the laser device is in working.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
2/ 9
6) The device has four cooling fans at the rear panel to dissipate heat. In order to guarantee
enough airflow to help giving heat off, there must be a space of at least 10 cm’s width for
airflow in front and rear side of the device. As the cooling fans are working at blow condition,
if laser is mounted in a cabinet with fans, the direction should be same as laser’s fans.
7) Do not look into the output head of the device directly. Please do wear appropriate laser
safety eyewear during the time when operating the device.
8) Make sure the pulse repetition rate higher than 20 kHz.
9) For the longest time without pulse is only 100 us. If there is no pulse output, please stop
marking at once, to avoid further damage of the device.
10) Power source sudden interruption will do great harm to the laser device. Please make sure
the power supply works continuously.
1.4. Specifications
Table 2. 70Q/100Q pulsed fiber laser specifications
Pulsed fiber laser
70Q
100Q
Wavelength
（
nm
）
1060~1085
1060~1085
Polarization
Random
Random
Optical isolator
Yes
Yes
Nominal average output power (W)
≥70@70～100kHz ≥100@100～200kHz
Single pulse energy (mJ)
1@20～70kHz 1@20～100kHz
Beam quality（M
2
）≤1.6 ≤1.6
Beam Diameter
（
mm
）
6
～
8
6
～
8
Pulse duration
（
ns
）
50
～
130@70kHz
50
～
130@100kHz
Pulse repetition rate
（
KHz
）
20 - 100 20 - 200
Output Power Tunability（%）10-100 10-100
Output Fiber Cable length（m）2.0 2.0
Working voltage（VDC）24±1 24±1
Power consumption（20℃）（W）400 450
Cooling
Forced Air Cooled
Forced Air Cooled
Dimension W×D×H（mm）
396×360×123
396×360×123
Operating temperature
0℃～40℃0℃～40℃
Store temperature
-20℃～60℃-20℃～60℃
humidity ＜80% ＜80%

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
3/ 9
2.Mounting
2.1 Mounting dimensions
1) Fiber Laser module dimensions (As shown in Fig. 1).
Figure 1. Dimension drawing of laser module (Unit: mm).
2) Isolated output head dimensions (As shown in Fig. 2).
Figure 2. Dimension drawing of output isolator (Unit: mm).
2.2 Method of installation
1) Fix the module stable to the bracket and keep the laser in good ventilation.
2) Connect the power line to 24VDC power and ensure enough DC output power. Keep it clear
to the polarity of the electric current: anode-brown; cathode-blue; PE-yellow and green. The

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
4/ 9
definition figure is shown in Fig. 3.
Figure 3. Definition of power line wires
3) Make sure that the interface of the external controller matches the laser and the control cable
is well connected to the laser’s interface. The recommended electrical connection is shown in
Fig. 4.
User
’s
cont
rolle
r
DB25
Controller
interface
Power
supply
wire
Laser
Module
24V+(Brown)
L
N
GND
External GND
24V
power
supply
24V-(Blue)
Figure 4. Schematic of recommended electrical connection
4) The bending radius of the delivery fiber should not exceed 15 cm.
24V+
GND
24V-

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
5/ 9
3.Control Interface
There are DB9 and DB25 interfaces at the rear of the laser. The DB9 is a RS232 interface
only used for debugging, no needs to connect. And DB25 is the joint interface connecting control
system with laser system, please make sure the connection is reliable before operation. Feet of
the DB25 are defined as follows in Fig. 5.
Figure 5. Connect port of controller
Table 3 Definition of connect ports of controller
PIN No.
Name
Description
1-8 (D0-D7) Power Setting
8 bit Parallel port;
D0 is minimum bit and D7 is maximum bit; Range: 0-255
(hexadecimal: 0X00-0XFF)
10,13-15,24-25
Ground
Digital GND
11,12,16,21
Laser alarms status
See alarm codes in table 5
17 VCC
+5VDC power supply input for independent operation of
the guide laser and PCB
18 EE
Emission Enable (EE) signal.
HIGH (>3V): Emission Enable
LOW or disconnected (<1V): Emission Disable
19 EM
Emission Modulation (EM) input.
HIGH (>3V): Emission ON
LOW or disconnected (<1V): Emission OFF
20 Sync
Pulse Repetition Rate (Synchronization) input, square
wave. (70-100kHZ)/(20-200kHZ)
22
Guide Laser signal
Guide Laser (red diode) ON/OFF input.
9,23
Obligate PIN
Reserved
1) The pump current of diode laser and the laser output power are controlled by setting the
value of PIN1-PIN8 (TTL level). PIN1-PIN8 can be set from 0～255，corresponding to the

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
6/ 9
laser output power from 0～100％(the actual laser power may not be strictly linear with the
setting value). The relationship between PIN value and output power is shown in Table 4:
Table 4 Definition of power control PIN value
Setting 1
Setting 2
Setting 3
Setting 4
Setting 5
PIN 1
0
0
0
0
1
PIN 2 0 0 0 0 1
PIN 3
0
0
0
0
1
PIN 4
0
0
0
0
1
PIN 5
0
0
0
1
1
PIN 6
0
0
1
1
1
PIN 7 0 1 1 1 1
PIN 8
1
1
1
1
1
Current
~50 %
~75 %
~87.5 %
~93.75 %
100%
2) Alarms status: Pins 11, 12, 16 and 21 are the alarm and status outputs. Pin 12 is reserved
(always be high). These pins indicate the following device states.
Table 5 Definition of alarm signal
PIN 12
PIN 11
PIN 16
PIN 21
Alarm item
×Low Low Low Temperature alarm
×
Low
Low
High
Normal
×
Low
High
Low
Obligate alarm
×
Low
High
High
System alarm
×
High
Low
Low
Supply voltage alarm
×High Low High Obligate alarm
×
High
High
Low
Obligate alarm
×
High
High
High
Obligate alarm
3) PIN 17 is the external 5V input, providing power supply for alarm signal; input current must
be > 20 mA.
4) External input signals (PIN 1-8, 18-20, 22) are all connected to the optical coupler inside the
system. External 17 pin 5V power supply should be connected to ensure the effective signal.
Caution: Before turning on PIN 19, PIN 18 must be switched on, or the laser may be
damaged. The signal of PIN 18 must be ahead of PIN 19 at least 5 ms.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
7/ 9
5) I/O connection of digital signal: the supply current of input signals are less than 10mA, and
the supply current of output signals are less than 3 mA. The connection circuit of input and
output signals is shown in Figure 6.
Figure 6. Schematic of input and output signals.
6) The control board and laser driver can be powered separately. When there is failure in 24V
control board power supply, the laser will stop emission after 20 ms. When there is failure in
24V laser driver power supply, the laser will stop emission after 4 ms.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
8/ 9
4. Operation Regulations
4.1 Pre-inspection
1) Make sure the device appearance is in good condition and the output fiber is neither
excessively bended nor broken.
2) Make sure signal line of laser and marking system are properly connected.
4.2 Operation procedures
1) Starting procedures
Please make sure the control system is on before you turn on the fiber laser. Only after at
least 1 minute since the power turned on, the subsequent operations can be preceded.
2) Frequency set introductions
For model P70Q, the frequency setting range is from 20 kHz to 100 kHz.
For model P100Q, the frequency setting range is from 20 kHz to 200 kHz.
3) Laser marking checking
For the device initial testing, first turn the power down to zero without turning on the
marking system after the device is successfully started. Then draw a quadrate, marking
continuously while slowly increasing the power from zero to 100% at the same time. Meanwhile,
use a ceramic material to observe the laser and the laser should become stronger, otherwise shut
down the device and check. If operating normally, the marking system can be used in common
order afterwards.
4.3 Cautions
1) Marking frequency must be in the range of 20~100 kHz for P70Q, 20~200 kHz for P100Q.
2) It should not modulate the frequency while marking.
3) Stop marking first before shutting down the device, then turn the power down to zero and cut
the power off.

User’s guide Ytterbium Pulsed Fiber Laser RFL-P70Q～P100Q Ver.: 2.0
9/ 9
5.Instructions for warranty, return and maintenance
5.1 General warranty
All products are warranted by Raycus against defects and problems in materials and
workmanship during the warranty period according to the purchase order or specifications and
we guarantee the product will accord with the specification under normal use.
Raycus has the right to choose to repair or replace any product that proves to be defective in
materials and workmanship selectively during the warranty period. Only products with particular
defects are under warranty. Raycus reserves the right to issue a credit note for any defective
products produced in normal conditions.
5.2 Limitations of warranty
The warranty does not cover the maintenance or reimbursement of our product of which the
problem results from tampering, disassembling, misuse, accident, modification, unsuitable
physical or operating environment, improper maintenance, damages due to excessive use or not
following the instructions caused by those who are not from Raycus. Customer has the
responsibility to understand and follow this instruction to use the device. Any damage caused by
fault operating is not warranted. Accessories and fiber connectors are excluded in this warranty.
According to the warranty, client should write to us within 31days since the defect is discovered.
This warranty does not involve any other party, including specified buyer, end-user or customer
and any parts, equipment or other products produced by other companies.
5.3 Service and repairs
Raycus is responsible for all the maintenance, for there is no accessory available inside for
users to use. Please contact Raycus as soon as possible when problems under warranty about
maintenance happen to the product. The product returned with permission should be placed in a
suitable container. If any damage happens to the product, please notify the carrier in document
immediately.
All the items about warranty and service above provided by Raycus are for uses’ reference,
formal contents about warranty and service are subject to the contract.
© Wuhan Raycus Fiber Laser technologies Co. Ltd, 2018.All Rights Reserved.