Raypak TempTracker mod+ Hybrid User manual

HTC# 059105-00D
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION
MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O
L
N
P
1514
VLTmA
CUR / VLT
181716
VLTmAGND
CUR / VLT
212019
VLTmAGND
CUR / VLT
242322
VLTmAGND
CUR / VLT
J
11 12
K M OL N P
E F G H
K ML N
13
GND
16
GND
19
GND
22
GND
2726
VLTmA
CUR / VLT
302916
VLTmAGND
CUR / VLT
25
GND
28
GND
I J
O P
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
HYBRID







P/N 241382 REV.3
Cat.# 5000.69 04/15/11
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID



2 Raypak, Inc.
HTC# 059105-00D

 . . . . . . . . . . . . . . . . . . 3
. . . . . . . . . . . . . . . . 4
 . . . . . . . . . . . . . . . . . . 4
 . . . . . . . . . . . . . . . . . . 5
 . . . . . . . . . . . 6
 . . . . . . . . . 7
 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Make Sure You Have the Right Control . . . . . . . . . 9
 . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mounting the Enclosure. . . . . . . . . . . . . . . . . 10
Install the Sensors . . . . . . . . . . . . . . . . . . . . 11
System Sensor Installation . . . . . . . . . . . . . . . . 11
Outdoor Sensor Installation . . . . . . . . . . . . . . . . 11
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Wiring the Power . . . . . . . . . . . . . . . . . . . . . 12
Wiring the Sensors . . . . . . . . . . . . . . . . . . . . 12
Wiring the Shutdown, Tstat, or Setback . . . . . . . . . . 12
Wiring the Prove . . . . . . . . . . . . . . . . . . . . . 13
Wiring the Indirect Domestic Hot Water (DHW) Call . . . . 13
Wiring the System Output. . . . . . . . . . . . . . . . . 13
Wiring the Boilers. . . . . . . . . . . . . . . . . . . . . 14
Wiring Boiler Activation or On/Off Staging Boilers . . . . . 14
Wiring Multi-Stage Boilers . . . . . . . . . . . . . . . . 14
Wiring to Modulating Boilers . . . . . . . . . . . . . . . 14
Wiring the 4-20mA Modulating Boilers . . . . . . . . . . 15
Wiring the Voltage Modulating or Staging Boilers . . . . . 15
Connecting to the Extensions and 4-20mA EMS Interface 16
Connecting to BACnet Interface Module . . . . . . . . . 17
 . . . . . . . . . . . . . . . . . . 18
 . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . 20
Program Change Switch Setting . . . . . . . . . . . . . 20
Startup Sequence . . . . . . . . . . . . . . . . . . . . 20
Boiler Type . . . . . . . . . . . . . . . . . . . . . . . . 20
Sensor Type . . . . . . . . . . . . . . . . . . . . . . . 20
EMS Input Mode . . . . . . . . . . . . . . . . . . . . . 20
EMS 4mA and 20mA Set Points. . . . . . . . . . . . . . 21
HYBRID Startup Settings . . . . . . . . . . . . . . . . 21
Switch Set Point . . . . . . . . . . . . . . . . . . . . . 21
Switch Differential . . . . . . . . . . . . . . . . . . . . 21
Switch Delay . . . . . . . . . . . . . . . . . . . . . . . 22
Heavy Load Sequence 2nd Group . . . . . . . . . . . . 22
Condensing and Non-Condensing Boiler Type . . . . . . 22
Condensing and Non-Condensing Boiler Number . . . . . 22
HYBRID Modulating Boiler Settings . . . . . . . . . . 23
Modulating Output Type . . . . . . . . . . . . . . . . . 23
Modulating Mode . . . . . . . . . . . . . . . . . . . . . 23
HYBRID Staging Boiler Settings . . . . . . . . . . . . 23
Staging Output Type . . . . . . . . . . . . . . . . . . . 23
Staging Mode . . . . . . . . . . . . . . . . . . . . . . 24
Modulating Boiler Settings . . . . . . . . . . . . . . . 24
Boiler Number . . . . . . . . . . . . . . . . . . . . . . 24
Modulating Output Type . . . . . . . . . . . . . . . . . 24
Modulating Mode . . . . . . . . . . . . . . . . . . . . . 24
Staging Boiler Settings . . . . . . . . . . . . . . . . . 25
Staging Output Type . . . . . . . . . . . . . . . . . . . 25
Boiler Number . . . . . . . . . . . . . . . . . . . . . . 25
Staging Mode . . . . . . . . . . . . . . . . . . . . . . 25
Startup Settings (Continued) . . . . . . . . . . . . . . 25
Prove/Indirect Domestic Hot Water (DHW) Priority . . . . 25
Indirect Domestic Hot Water Set Point . . . . . . . . . . 26
Shutdown/Tstat/Setback Mode . . . . . . . . . . . . . . 26
Boost Mode . . . . . . . . . . . . . . . . . . . . . . . 26
Sensor Fault . . . . . . . . . . . . . . . . . . . . . . . 26
BACnet Mode . . . . . . . . . . . . . . . . . . . . . . 27
BACnet Baud Rate . . . . . . . . . . . . . . . . . . . . 27
MS/TP Address. . . . . . . . . . . . . . . . . . . . . . 27
BACnet ID . . . . . . . . . . . . . . . . . . . . . . . . 27
 . . . . . . . . . . . . . . 27
 . . . . . . . . . . . . . . . . 28
 . . . . . . 29
Setting the Control to Factory Defaults . . . . . . . . 30
Program Change Switch Setting . . . . . . . . . . . . . 31
Season. . . . . . . . . . . . . . . . . . . . . . . . . . 31
Reset Ratio. . . . . . . . . . . . . . . . . . . . . . . . 31
Offset . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Outdoor Cutoff Temperature . . . . . . . . . . . . . . . 32
Minimum Water Temp . . . . . . . . . . . . . . . . . . 32
Maximum Water Temp . . . . . . . . . . . . . . . . . . 32
 . . . . . . . . . . . . . . . . . . . . 31
System Settings . . . . . . . . . . . . . . . . . . . . . 33
Setback . . . . . . . . . . . . . . . . . . . . . . . . . 33
Purge Delay . . . . . . . . . . . . . . . . . . . . . . . 33
System Run-On . . . . . . . . . . . . . . . . . . . . . 33
Lead Boiler Rotation . . . . . . . . . . . . . . . . . . . 34
Standby Time. . . . . . . . . . . . . . . . . . . . . . . 34
Last Stage Hold . . . . . . . . . . . . . . . . . . . . . 34
Lead Stages . . . . . . . . . . . . . . . . . . . . . . . 34
Modulating Boiler Operating Settings . . . . . . . . . 35
Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Lag Delay . . . . . . . . . . . . . . . . . . . . . . . . 35
Soft-Off Delay . . . . . . . . . . . . . . . . . . . . . . 35
Staging Boiler Operating Settings . . . . . . . . . . . 36
Reaction Time . . . . . . . . . . . . . . . . . . . . . . 36
Minimum Runtime . . . . . . . . . . . . . . . . . . . . 36
Day / Night Schedule . . . . . . . . . . . . . . . . . . 37
Set Time . . . . . . . . . . . . . . . . . . . . . . . . . 37
Maintenance . . . . . . . . . . . . . . . . . . . . . . . 37
System & Outdoor Sensor Trim . . . . . . . . . . . . . . 37
Output Modulation Trim . . . . . . . . . . . . . . . . . . 38
Conguration . . . . . . . . . . . . . . . . . . . . . . . 38
Display . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Boiler Status . . . . . . . . . . . . . . . . . . . . . . . 39
Display Modulating Boiler Status . . . . . . . . . . . . . 39
Display Staging Boiler Status . . . . . . . . . . . . . . . 39
Display Messages . . . . . . . . . . . . . . . . . . . . 40
 . . . . . . . . . . . . . . . . . . . . 39
Boiler Stage Settings . . . . . . . . . . . . . . . . . . 40
Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Ignition % . . . . . . . . . . . . . . . . . . . . . . . . 41
Modulation Start % . . . . . . . . . . . . . . . . . . . . 41
Copy Settings - Boiler A Only . . . . . . . . . . . . . . . 42
 . . . . . . . . . . . . . . . . . . . . . 42
 . . . 44
 45
 . . . 46
 . . . . 47
 . . . . . . 48
. . . . . . . . . . . . . . . . . 49
 . . . . . . . . . . . . . . 50
Hybrid Piping Diagram . . . . . . . . . . . . . . . . . 50
Hybrid Wiring Diagram . . . . . . . . . . . . . . . . . 51
Modulating Piping Diagram. . . . . . . . . . . . . . . 52
Modulating Wiring Diagram. . . . . . . . . . . . . . . 53
Staging Piping Diagram. . . . . . . . . . . . . . . . . 54
Staging Wiring Diagram. . . . . . . . . . . . . . . . . 55
 . . . . . . . . . . . . . . . . . . . . . . . 56

TempTracker mod+ Hybrid Installation and Operation Manual 3
HTC# 059105-00D

In response to new advancement in condensing boiler design and size, many applications utilize multiple condensing boilers in
addition to the non-condensing boilers. That triggered Raypak's patent design of the TempTracker mod+ Hybrid . It is intended to
manage the two groups of boilers to maximize system efciency at the lowest operating cost while maintaining the desired comfort.
When Hybrid is selected as the Boiler Type, the TempTracker mod+ Hybrid will operate each group based on the Target temperature
switching set point. See "Boiler Type" on page 20..
Each of the condensing and non-condensing groups of boilers can be either modulating or staging. Modulating boilers can be of
4-20mA modulating signal or 0-10V modulating signal.
Staging boilers must be of the 0-10V signal.
Depending on the actual System Temperature, the
TempTracker mod+ Hybrid will determine which
group of boilers will be the lead and which group will
be the lag group. The Condensing group of boilers
will be the Lead group when the System temperature
is below the System Target Switching Set Point.
However, when the System temperature rises above the
Switching Set Point, the Non-Condensing boiler group
will be the lead group and the Condensing Group will
be the lag group.
Basically, the TempTracker mod+ Hybrid will allow
the condensing group of boilers to operate as along as
the System sensor is below the Switching Set Point.
See"Switch Set Point" on page 21. During that period,
if additional output boilers are needed, the TempTracker mod+ Hybrid will energize the Non-Condensing boilers to meet the load.
See"Heavy Load Sequence 2nd Group" on page 22. When less output is required the TempTracker mod+ Hybrid will de-energize the
Non-Condensing boilers prior to de-energizing the Condensing boilers.
To eliminate any short-cycling due to rapid changes in the Target Temperature used in the switching, an adjustable Switching Delay
has been incorporated. See"Switch Delay" on page 22.
For Hybrid settings, See "Boiler Type" on page 20. See "HYBRID Startup Settings" on page 21.
To set the Condensing and Non-Condensing boiler types See "HYBRID Modulating Boiler Settings" on page 23. Also, See "HYBRID
Staging Boiler Settings" on page 23.
Above the Switch Set Point
Non-Condensing are the Lead Group
Condensing are the Lag Group
Target Switch
Set Point = 120°F
Below the Switch Set Point
Condensing are the Lead Group
Non-Condensing are the Lag Group
120°F
140°F
100°F
SWITCH MODE = Target Temperature
CONDCOND
NON-
COND
NON-
COND
NON-
COND
NON-
COND
CONDCOND
SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
34567 8 91011 12 13 15
14 17
16 18 22
20
19 21 24
23 29
25 27
26 28 32
3031
LN
-+
+
TT
OORS-485
mAGND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mAGND VLT
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/TSTAT
/SETBACK
OD=25oF SYS= 145oF
<<A>> B
100% 52%
System
Temp SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
34567 8 91011 12 13 15
14 17
16 18 22
20
19 21 24
23 29
25 27
26 28 32
3031
LN
-+
+
TT
OORS-485
mAGND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mAGND VLT
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/TSTAT
/SETBACK
OD=25oF SYS= 145oF
<<A>> B
100% 52%
Above the Switch Set Point
Condensing are the Lead Group
Non-Condensing are the Lag Group
Outdoor Switch
Set Point = 30°F
Below the Switch Set Point
Non-Condensing are the Lead Group
Condensing are the Lag Group
30°F
50°F
10°F
SWITCH MODE = Outdoor Temperature
CONDCOND
NON-
COND
NON-
COND
NON-
COND
NON-
COND
CONDCOND
Outdoor
Temp
SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
34567 8 91011 12 13 15
14 17
16 18 22
20
19 21 24
23 29
25 27
26 28 32
3031
LN
-+
+
TT
OORS-485
mAGND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mAGND VLT
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/TSTAT
/SETBACK
OD=25oF SYS= 145oF
<<A>> B
100% 52%
SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
34567 8 91011 12 13 15
14 17
16 18 22
20
19 21 24
23 29
25 27
26 28 32
3031
LN
-+
+
TT
OORS-485
mAGND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mAGND VLT
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/TSTAT
/SETBACK
OD=25oF SYS= 145oF
<<A>> B
100% 52%

4 Raypak, Inc.
HTC# 059105-00D

The Modulation PID logic provides the capability of controlling multiple modulating current or voltage boilers. When heat is
required, the control PID will activate the lead boiler and start its purge. See "Purge Delay" on page 33. This will be followed by the
initiation of its modulation at the Ignition %. See "Ignition %" on page 41. After the Purge period and when additional heat is needed,
the control shall start to increase the lead boiler modulation until the Modulation Start % has been reached. See "Modulation Start %"
on page 41. That shall be followed by the lag boiler purge initiation. The lead boiler shall resume its modulation while the lag boiler is
in purge until the lead boiler reaches full re (100% modulation). Any additional heat requirements will trigger the control to increase
the lag boiler modulation.
When the Temp Tracker mod+ Hybrid PID requires reduced output, it will reduce the modulation of the lag boiler until it reaches its
Ignition %. That shall be followed by the reduction of modulation of the lead boiler until it reaches 40% percent of the Modulation
Start %. This shall trigger the control to turn off the lag boiler. The control will keep reducing the lead boiler modulation until it
reaches its Ignition %. If the Last Stage Hold was activated, the control will hold the lead boiler at the Ignition % until the System
Temperature exceeds the Target Set Point by the Last Stage hold setting. See "Last Stage Hold" on page 34.
For Modulating boilers, See "Boiler Type" on page 20. Also, See "Modulating Boiler Settings" on page 24.

The Staging PID control logic is primarily used with multi-stage boilers. The logic will utilize two primary settings to add or subtract
stages. The Reaction Time is used to turn on/energize stages. See "Reaction Time" on page 36. The Minimum Runtime is used to turn off/
de-energize stages. See "Minimum Runtime" on page 36. A call for heat, by either closing the TSTAT input or opening the SHUTDOWN
input while the outdoor temperature is below the Outdoor Cutoff, will trigger the Temp Tracker mod+ Hybrid to turn on/energize the lowest
ring stage of the Lead Boiler to start its Purge. See "Purge Delay" on page 33. After the elapse of the purge period, the Temp Tracker
mod+ Hybrid will start calculating the Reaction Period. If after a full Reaction Time the control logic foresees the need for additional
stages, the TempTracker mod+ Hybrid will energize the following stage. If that stage was another boiler, that boiler has to go through a
full Purge Delay before starting to calculate the Reaction Time for that stage. Otherwise, if the next stage was the higher ring stage on
the same boiler, the Reaction Time will start from the moment the higher ring stage relay is energized.
When the Temp Tracker mod+ Hybrid PID logic foresees that the system will overshoot, regardless of the current system and
target values, it will make sure that the last stage turned on/energized has elapsed a full Minimum Runtime before it is turned off/
de-energized. Except for the lead stage, no additional stages will be turned off/de-energized until another full Minimum Runtime is
elapsed. On the other hand, if the last stage is a lead stage, it will remain energized until the system reading exceeds the target set
point by the Last Stage Hold value in addition to satisfying the Minimum Runtime condition. That is, if the Set Point was 150°F and
the Last Stage Hold was set to 10°F, the lead stage will remain energized until the system reaches 160°F and a full Minimum Runtime
elapses. This is useful in protecting the lead stages from short cycling.

TempTracker mod+ Hybrid Installation and Operation Manual 5
HTC# 059105-00D

The TempTracker mod+ Hybrid has multiple operating modes that satisfy most
hydronic systems. It changes the System Set Point based on outdoor temperature
(Outdoor Reset). The TempTracker mod+ Hybrid varies the temperature of the
circulating heating water in response to changes in the outdoor temperature. The
heating water temperature is controlled through the modulation or sequencing of the
stages.
The TempTracker mod+ Hybrid also controls the system circulating pump with an
adjustable Outdoor Cutoff. When the outdoor temperature is above the Outdoor
Cutoff, the pump is off and no heating water is circulated through the system. When
the outdoor temperature drops below the Outdoor Cutoff, the system pump relay is
activated and the heating water circulates through the system. The temperature of
the heating water is controlled by the Reset Ratio, Water Offset, and changes with
Outdoor temperature.

When a building is being heated, heat escapes through the walls, doors, and windows
to the colder outside air. The colder the outside temperature, the more heat escapes.
If you can input heat into the building at the same rate that it is lost out of the
building, then the building temperatures will remain constant. The Reset Ratio is an
adjustment that lets you achieve this equilibrium between heat input and heat loss.
The starting point for most systems is the 1.00 (OD):1.00 (SYS) (Outdoor
Temperature : Heating Water Temperature) ratio. This means that for every degree
the outdoor temperature drops, the temperature of the heating water will increase
one degree. The starting point of the curves is adjustable, but comes factory selected
at 70°F Outdoor Temperature and 100°F Water Temperature. For example with
a 1.00 (OD):1.00 (SYS) ratio, if the outdoor temperature is 50°F, this means the
temperature has fallen 20° from the starting point of 70°F. Therefore, the heating
water temperature will increase 20° to 120°F.
Each building has different heat loss characteristics. A very well insulated building
will not lose much heat to the outside air, and may need a Reset Ratio of 2.00
(OD):1.00 (SYS) (Outdoor:Water). This means the outdoor temperature would have
to drop 2 degrees to increase the water temperature 1 degree. On the other hand, a
poorly insulated building with insufcient radiation may need a Reset Ratio of 1.00
(OD):2.00 (SYS). This means that for each degree the outdoor temperature dropped
the water temperature will increase 2 degrees. The TempTracker mod+ Hybrid has a
full range of Reset Ratios to match any buildings heat loss characteristics.
A heating curve that relies not only on Outdoor temperature but also on the type of
radiation will improve heat comfort. The following are suggested initial settings for
different types of radiation based on average building insulation and heat loss. The
contractor can ne tune these adjustments based on the specic building need.
  
Radiators (Steel & Cast Iron) 1.00 (OD) : 1.00 (SYS) 0˚F
Baseboard (Finned copper tube& Cast Iron) 1.00 (OD) : 1.00 (SYS) 0˚F
Radiant (High Mass/Concrete) 4.00 (OD) : 1.00 (SYS) -10˚F
Radiant (Low Mass/Joists) 2.00 (OD) : 1.00 (SYS) -10˚F
Fan Coils & Air Handlers 1.00 (OD) : 1.00 (SYS) 20˚F
Outdoor Temperature
Water Temperature
70 405060
130
120
110
100
Outdoor Temperature
Water Temperature
70 405060
110
100
90
80
Outdoor Temperature
Water Temperature
70 405060
150
140
130
120
1:4
With a 0° Offset, the
Reset curves begin at
100° Water Temperature.
With a -20° Offset, the
Reset curves begin at
80° Water Temperature.
With a +20° Offset, the
Reset curves begin at
120° Water Temperature.
1:4
1:4 1:1
1:1
1:1
4:1
4:1
4:1
90
100
+20 Offset
-20 Offset
Outdoor Temperature
Water Temperature
70 405060
130
120
110
100
1:4 1:1
4:1
Colder
Warmer
Outdoor Temperature (in °F)
70 60 50 40 20
30 0 -10
10 -20
100
120
110
130
140
150
160
180
170
190
200
210
220
1:3 1:2 1:1.5
1:1.25
1:1
1.25:1
1.5:1
2:1
3:1
4:1
Water Temperature (in °F)
Reset Ratio Curves
Reset Ratio is Presented as
Outdoor Temp. : Water Temp. Ratio
1:4

6 Raypak, Inc.
HTC# 059105-00D
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
The digital display shows the system status, set point,
lead stage <in brackets>, and status of each stage.
To view and adjust settings, press the appropriate buttons.
LED indicates the
associated relay status.
Buttons function is presented on
Bottom Row of display.
Program Switch to restrict access to
function changes. This switch is
covered with Wiring Enclosure.
120VAC Power
Four N.O. Boiler startup relay
outputs. Each is wired in series
with each boiler's limit circuit.
System Output controls
pumps, valves, or other
system components.
Four modulation/staging outputs can be
4-20mA or Voltage. Go to Startup Menu
to determine the type of output for each stage.
When connecting the control Outdoor Air
Sensor (#013398F) and System Sensor (#012187F), no
Polarity is observed. Prove terminals must be connected
for TempTracker mod+ Hybrid to operate boilers.
Connect Extension panels to add
additional stages using a RJ11 cable(cable
provided with Extension) and RJ45-RJ11
Adaptor (Supplied with control) only or add
BACnet Interface Module using RJ45
(cable provided with BACnet
Interface Module)

Complete TempTracker mod+ Hybrid Part Number 011922

TempTracker mod+ Hybrid Installation and Operation Manual 7
HTC# 059105-00D
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION
MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O
L
N
P
1514
VLTmA
CUR / VLT
181716
VLTmAGND
CUR / VLT
212019
VLTmAGND
CUR / VLT
242322
VLTmAGND
CUR / VLT
J
11 12
K M OL N P
E F G H
K ML N
13
GND
16
GND
19
GND
22
GND
2726
VLTmA
CUR / VLT
302916
VLTmAGND
CUR / VLT
25
GND
28
GND
I J
O P
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
120VAC Power
Six N.O. Boiler startup relay
outputs. Each is wired in series
with the boiler's limit circuit.
Six modulating outputs can be 4-20mA or voltage.
Go to TempTracker mod+ Hybrid Startup Menu to
determine the type of output for each stage.
LED indicates the
associated relay status.
Connect to any TempTracker mod+ or Hybrid
and additional Extension panels to add
additional stages using a RJ11 cable only
(cable provided with TempTracker mod+ Ext).
Extension Selection Switch to determine
Stage letters and LED colors.
Ext-A Stages E - J and all LEDs are Green
Ext-B Stages K - P and all LEDs are Red
This switch is covered with the Wiring Enclosure.
HYBRID

Complete TempTracker mod+ Extension Part Number 013179F

8 Raypak, Inc.
HTC# 059105-00D

The TempTracker mod+ Hybrid has been designed with Hydronic building heating, using both condensing and non-condensing
boilers, as the primary purpose. As well, it is capable of controlling modulating or staging boilers. With this in mind, many of the
TempTracker mod+ Hybrid features can be utilized to ease, enhance, and improve your system performance.

The TempTracker mod+ Hybrid can operate both modulating and staging boilers. Just specify each of the Condensing and Non-Condensing
boiler group type and the TempTracker mod+ Hybrid will activate the groups based on an adjustable set of criteria.

The TempTracker mod+ Hybrid's control algorithms allow it to look at the rate of change in the system. If the system temperature is
changing quickly, the TempTracker mod+ Hybrid will react quickly to adjust the modulating stages’ output. If the system temperature
changes slowly, the TempTracker mod+ Hybrid will make slow and gradual output adjustments. Therefore, the TempTracker mod+ Hybrid
adapts to specic system requirements and minimizes uctuations around the set point.

Whenever any of the Condensing or Non-Condensing group type is set to Modulating, the TempTracker mod+ Hybrid will accurately control
the output from 0 to 100% of modulation for each of these different types of motors. Moreover, a single TempTracker mod+ Hybrid can
control multiple modulating burners each with a different modulating signal.

Whenever one of the Condensing or Non-Condensing group Type is set to Staging, the TempTracker mod+ Hybrid will accurately
sequence the stages using a PID logic. The sequencing group will have a set of adjustable parameters to help achieve better operation.

The TempTracker mod+ Hybrid’s alphanumeric digital display names each system parameter in simple English and shows its precise
value. The easy to follow menu system allows users to quickly make changes to any system setting without having to learn any specialized
codes or keyboard commands.

Rotating the lead stage of each group promotes even wear. The TempTracker mod+ Hybrid has three modes of rotation: Manual, Last
On, or Time. The Time rotates the lead stage every selected time period from every hour to every 60 days.

The TempTracker mod+ Hybrid has a hydronic outdoor temperature reset function. This allows the TempTracker mod+ Hybrid to change
the set point based on outdoor temperature. Furthermore, additional settings have been added to ne tune this operation, like Offset,
Minimum, and Maximum Water Temperature and night setback schedule.

This output can be used to activate a system pump, combustion air damper, or perform any other function that is required when any stage
is active. It will energize whenever the outdoor temperature is below the Outdoor Cutoff setting. A System Prove input checks the status
of components activated by the System output before stages can be activated.

The TempTracker mod+ Hybrid can stage modulating boilers as needed. In Normal Modulation, it will allow the modulation to increase
on the lead boiler until it reaches its modulation start point adjustment. Then, the TempTracker mod+ Hybrid will start the next boiler
and so on. Moreover, the TempTracker mod+ Hybrid allows for a parallel mode that can modulate several boilers together as a one large
boiler. This mode is useful when used with condensing boilers as they run more efcient at lower modulation. Thus, it is better to run
several boilers at lower modulation than to run a single boiler at full re.

As a stand-alone, the TempTracker mod+ Hybrid is designed to control four stages. However, it has the capability of expanding its control
to two extension panels each with six boiler stages. Thus, the TempTracker mod+ Hybrid can control a total of up to 16 boiler stages.

TempTracker mod+ Hybrid Installation and Operation Manual 9
HTC# 059105-00D

Two Setback modes are available for the TempTracker mod+ Hybrid:
• The Day/Night Scheduling provides an adjustable time-based schedule for the Setback (only available when Shutdown or Tstat is
selected as the Setback/Shutdown Startup option). See "Shutdown/Tstat/Setback Mode" on page 26.
• The Setback mode uses an external signal to switch the operation of the TempTracker mod+ Hybrid in and out of setback mode (only
available when Setback is selected as the Setback/Shutdown Startup option).

By connecting the control to the optional 4-20mA EMS Interface, the control shall be capable of accepting a remote set point.

An optional BACnet Interface Module (#651735) can be used to connect the control to a BACnet MSTP network for remote access.

If you need the TempTracker mod+ Hybrid to do additional tasks that either are not listed or do not know how to congure them,
contact your local Raypak representative.
Setting an Initial Program will ease the conguration of the TempTracker mod+ Hybrid and will give the opportunity to utilize many of
the energy saving features while giving comfortable heat when needed.
The program should consist of the following:
• Selecting the features that your system can utilize.
• Installation: Install the Control, switches and sensors. See"Installation" on page 10
• Setting the System Startup. See "Startup Settings" on page 20.
• Setting the System Operating Settings. See "Operating Settings" on page 31
• Setting the Stages. See "Modulating Boiler Operating Settings" on page 35. Also, see "Staging Boiler Operating Settings" on page 36
• Adjusting Reset Ratio and Water Offset (In Reset Mode Only). See "Reset Ratio" on page 31

10 Raypak, Inc.
HTC# 059105-00D

Each of the TempTracker mod+ Hybrid or Extension consists of three primary enclosure components.
• TheEnclosureDisplayModule: contains the control electronic board, display, buttons, LEDs and electric wiring terminals. It has
two screws to hold it to the base. A program conguration switch, used to adjust the control settings, is placed above the terminals.
This switch is enclosed with the enclosure wiring cover for security. Wiring terminals are of the plug-in type to ease installation and
removal.
• TheEnclosureBase: contains the holes to mount and hold the control against the wall or any at surface. All other enclosure
components mount on the base. The bottom section of the Enclosure Base contains the wiring chamber with knockouts on the
bottom to ease installation.
• TheEnclosureWiringCover: seals the wires from the external environment. It has two screws to hold it the base and a hole to
secure a lock on the wiring enclosure. A plastic web that separates the wiring chamber into high and low volt sections has been
provided.

• Select a location near the equipment to be controlled.
• The surface should be at and sufciently wide and strong to hold the TempTracker mod+ Hybrid or the Extension.
• Keep the control away from extreme heat, cold, or humidity. Ambient operating temperature is from 20 to 120°F.
• Remove the Enclosure Wiring Cover from the control enclosure by removing the two bottom screws.
• Remove the Enclosure Display Module by removing the enclosure middle screws.
• Screw the Enclosure Base to the surface through the upper and lower mounting holes on the back of the enclosure.
• Replace the Enclosure Display Module and replace the enclosure middle screws.
• Do not replace the enclosure wiring cover until all wiring is done.
• When purchasing a padlock for the enclosure, the maximum shank diameter should not exceed ¼"
Enclosure Display Module
Enclosure Wiring Cover Enclosure Base
Hole for optional lock
(not supplied)
Mounting Holes
Display Mounting Screws
Wiring Cover
Mounting Screws

TempTracker mod+ Hybrid Installation and Operation Manual 11
HTC# 059105-00D


• Only use the System sensor (#012187F) provided with the unit.
• The sensor wires can be extended up to 500' using a shielded 2-conductor cable
(Belden #8760 or equivalent). Do not ground the shield at the sensor but at the
panel using one of the terminals marked with an “O”.
• Do not run sensor wires in conduit with line voltage wiring.
• Install a 3/8"ID 1/2"NPT immersion well.
• If installing the system sensor on the supply, insert the sensor in a well with heat
paste approximately 5' feet past the boiler loop outlet on the common supply
header but before any major takeoffs. The sensor must be located where it sees
the output of all the boiler stages. If a boiler is piped so that the sensor does
not see its output, the TempTracker mod+ Hybrid will not sequence the boilers
correctly.
• The sensor can also be installed on the return to the boilers after all major returns
and before any boiler. However, when setting the reset ratio and the offset, the
user must consider the temperature drop across the building loop.
Shield
Immersion Well
3/8" ID 1/2" NPT
Immersion Heating System Sensor
Common Supply Pipe
Heating System
Sensor Sensor Probe
Common Supply Pipe
Strap-On Heating System Sensor
Pipe Insulation
Sensor Probe
Shield
Connect
To control

If the HSS can not sense the
correct water temperature, the
TempTracker mod+ Hybrid will not
provide comfortable heat levels.

Use only the System and Outdoor Air sensors included with the control. Do
not use boiler sensors as it will cause operational problems.

• Only use the Raypak Outdoor Air Sensor group included with the unit
(#013398F).
• Locate the sensor in the shade on the north side of the building. The sensor
should never be in direct sunlight.
• Be sure the location is away from doors, windows, exhaust fans, vents, or other
possible heat sources.
• The sensor should be mounted approximately 10' feet above ground level.
• Adhere the Outdoor Label provided to the back of the sensor base.
• Use the Enclosure Base bottom knockout for the conduit. Use the locknut to hold
the conduit and enclosure base together. Screw the cover to the base.
• If screws are used to afx the enclosure to the wall, make sure to seal around the
sensor and wall except from the bottom.
• The sensor wires can be extended up to 500' using shielded 2-conductor cable
(#18/2). Do not ground the shield at the sensor but at the control using the
terminal marked with an “O”.
• Do not run sensor wires in conduit with line voltage wiring.

Determining the proper location of the Outdoor Sensor is very important. The TempTracker mod+ Hybrid
will base the heat on the outdoor temperature information it receives from this location. If the sensor is in
the sun, or covered with ice, its reading will be different from the actual Outdoor temperature (OD).
System Sensor
In Well
Shield
Not connected
Well Locknut
Sensor in Well
Well
Sensor 2-Conductor
Shielded Cable
System
Strap-On
Sensor
Shield
Not connected
Plastic
Tie-Wraps
Around Pipe
Strap-On Sensor
Immersion Sensor
Outdoor Sensor
snap-in location
Shield
not connected
Conduit
Outdoor Label
on back of Sensor
Outdoor Sensor
Mounting
screws
location
Seal around
sensor and wall
Outdoor
drip-hole

12 Raypak, Inc.
HTC# 059105-00D

• All wiring must enter the enclosure through the bottom knockouts.
• Class 1 voltage wiring must utilize a different knockout and conduit from any Class 2 voltage wiring.

(Terminals 1, 2)
• Bring the 120VAC 60Hz power wires through the bottom left knockout of the enclosure.
• Connect the hot line to terminal marked L.
• Connect the neutral line to the terminal marked N.
• Raypak recommends installing a surge suppressor on the power source to the TempTracker mod+ Hybrid.



SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Line
Neutral
120VAC
Power Source


Connect the shield at the control terminal end and cut the shield wire at the sensor end.
To avoid operational problems, use only the System and Outdoor Air sensors included with the control.

(Terminals 27, 28)
• A TempTracker mod+ Hybrid must be connected to a System temperature sensor (#012187F) located in the
common header. The sensor must be inserted in a 3/8 ID well using heat paste.
• Temperature sensor wires can be extended up to 500’ by splicing its wires with a shielded 2-conductor cable
(Belden #8760 or equivalent (#18/2)).
• Temperature sensors have no polarity. Connect the two wires from the sensor to the TempTracker mod+ Hybrid
terminals marked SYSTEM TEMP 27, 28.
• Connect the sensor shield to the circled terminal 28 with one of the sensor wires.
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23
29
25
27
26
28
32
30
31
LN
-+
+
T
T
O
O
RS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
O
O
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
System Sensor
Sensor Shield
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28
32
30 31
LN
-+
+
TT
OO
RS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Outdoor Sensor
Sensor Shield

(Terminals 25, 26)
• The TempTracker mod+ Hybrid will vary the system Set Point based on outdoor temperature. In addition, the
Outdoor Air Sensor group (#013398F) is used as an Outdoor Cutoff. The TempTracker mod+ Hybrid will disable
all boilers when the outdoor temperature is above the adjustable Outdoor Cutoff temperature.
• For an outdoor sensor use the outdoor sensor provided.
• The sensor wires can be extended up to 500’ using shielded 2-conductor cable (Belden #8760 or equivalent (#18/2)).
• Temperature sensors have no polarity. Connect the wires from the outdoor sensor to the TempTracker mod+ Hybrid
terminals marked OUTDOOR TEMP - 25, 26.
• Connect the shield to the circled terminal 26 with one of the sensor wires.

(Terminals 31, 32)
• The Shutdown will be available when selected as the Shutdown/Tstat/Setback mode from the Startup menu. See
"Shutdown/Tstat/Setback Mode" on page 26. This will provide the user with an adjustable Day/Night Schedule. See
"Day/Night Schedules" on page 37.
• The Shutdown feature can be used whenever it is desirable to turn off the TempTracker mod+ Hybrid stage outputs
from a remote location or another controller (i.e. EMS input).
• The Tstat option, when selected from the Shutdown/Tstat/Setback startup menu, offer the capability of controlling
the operation of the TempTracker mod+ Hybrid based on a thermostat input. This will provide the user with a
adjustable Day/Night Schedule.
• The thermostat will send the TempTracker mod+ Hybrid a call for heat by shorting terminals 31 and 32.
• When the Shutdown input is enabled by closing the dry contact, or when the Tstat input is disabled by opening the
dry-contact, all active modulating boilers will immediately modulate down to low for the Soft-Off period, then turn
off. All staging boilers will turn off immediately.
SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28
32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Shutdown,
T-Stat, or
Setback Signal

TempTracker mod+ Hybrid Installation and Operation Manual 13
HTC# 059105-00D
• The System Output relay will remain active until the System Run-On Delay expires and then it will turn off.
• When Setback is selected in the Startup, a BMS/EMS or external clock can provide a Setback signal using these
input terminals. See "Shutdown/Tstat/Setback Mode" on page 26. No Day/Night Schedule will be available when
Setback is selected from the Shutdown/Tstat/Setback mode in the Startup menu.
• Bring the two wires from the dry contact to the terminals marked SHUTDOWN/TSTAT/SETBACK- 31,32.
• The signal must be a dry contact only. No voltage can be placed across the SHUTDOWN/TSTAT/SETBACK
terminals.

(Terminals 29, 30)
• The Prove feature is provided to check system component operation and must be selected in the Startup Menu
from the Prove/DHW Sharing menu. See "Prove/Indirect Domestic Hot Water (DHW) Priority" on page 25.
• A typical use of this feature is to check for pump ow or combustion air damper status before ring any boiler.
• If the PROVE input is open on a call for heat, the TempTracker mod+ Hybrid will enable only the System Output.
All boiler outputs will be off when the PROVE input is open.
• A factory-installed jumper provides the System Prove signal. Do not remove the jumper unless it will be replaced
by a System Prove signal or these terminals are to be used for DHW call input.
• Bring the two wires from the dry contact to the terminals marked PROVE - 29, 30.
• Prove Input terminals can accept a dry-contact signal only. No voltage can be placed across these terminals.

The PROVE input cannot be used as a safety limit. All equipment must have its own
certied limit and safety controls as required by local codes. If Prove is selected in the
startup menu, no boiler stage will start unless Prove terminals are shorted. DO NOT
remove the PROVE jumper supplied unless replacing it with a Prove signal.
SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23
29
25 27
26 28
32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Prove Signal

(Terminals 29, 30)
• DHW can be used to raise system Set Point to the DHW Set Point as well as manage the System Pump according
to the DHW Priority setting. One of the DHW options must be selected from the Prove/DHW Sharing Startup
menu. See "Prove/Indirect Domestic Hot Water (DHW) Priority" on page 25.
• Wire an aquastat or a control to provide dry-contact closure on the DHW Call - 29, 30 terminals.
• Remove the jumper on the DHW terminals for proper operation.
• DHW Call terminals can accept dry contact signals only. No voltage can be placed across these terminals.
SYSTEM
A
B
C
D
12
RUNPROGRAM DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23
29
25 27
26 28
32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Indirect
DHW Signal

(Terminals 3, 4)
• The SYS output relay will energize and remain constantly energized whenever the outdoor temperature is below
the Outdoor Cutoff.
• When the outdoor temperature rises 2°F above the Outdoor Cutoff, the SYS output will remain energized for the
period set by the System Run-On then de-energize. See "System Run-On" on page 33.
• In addition, the System output will energize during summer DHW calls when DHW No Priority is selected. See
"Prove/Indirect Domestic Hot Water (DHW) Priority" on page 25.
• The SYS output has one Normally Open (N.O.) relay contact rated for (1/8 HP).
• The N.O. contacts are dry contacts only. They do not source any voltage.
• Class 1 voltages must enter the enclosure through a different opening from any Class 2 voltage wiring.
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
3456
78910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
System Pump
or Pump Starter
L
N

14 Raypak, Inc.
HTC# 059105-00D

• When wiring Condensing and Non-Condensing boilers make sure that Condensing boilers utilize the rst stages
and Non-Condensing boilers will utilize the following stages. That is, if the installation had two Condensing
Modulating boilers and two Non-Condensing Staging On/Off boilers, Stage A and B will be used by the
Condensing boilers while C and D will be used by the Non-Condensing boilers.

(A Terminals 5, 6), (B Terminals 7, 8), ...
• Each boiler output has a Normally Open (N.O.) dry-contact relay. They do not source any power.
• Wire the N.O. relay contacts in series with the unit’s limit circuit.
• When connecting to On/Off boilers, each stage relay output will be connected to a single boiler.
• Class 1 voltages must enter the enclosure through a different opening from any Class 2 voltage wiring.
• Note that some modulating boilers may not require the use of these outputs.
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678
910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS AB
CD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Boiler Enable
Output
Boiler

(For Staging Boiler Types Only) See Page 20
• Each multi-stage boiler must use only one of the N.O. relays and the
voltage output for that stage. The TempTracker mod+ Hybrid will
sequence the boiler stages using the 0-10V output signal.
• Note that on the display of the TempTracker mod+ Hybrid each
staging boiler will consist of a single letter.
• Each stage output has one Normally Open (N.O.) relay contact that
does not source any power.
• Class 1 voltages must enter the enclosure through a different opening
from any Class 2 voltage wiring.
OD=55oF SYS=142oF
<<A>> B
 HI LOW
STAGE◄►MENU

Each boiler "A" or "B" has multiple stages
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Boiler 1
Boiler 2
Boiler 3
Boiler 4
Boiler 1 Boiler 2
Voltage
Modulating
Signal Outputs
Outdoor Sensor
System Sensor
Prove Jumper
Do Not remove
Shield Shield
L
N
System Pump
L
N
Modulating
Condensing
Group (Boiler 1 & 2) {
Staging
Non-Condensing
Group (Boiler 3 & 4) {
Boiler 1 Boiler 2
Staging Voltage
Signal Outputs
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Boiler 1
Boiler 2
Boiler 3
Boiler 4
Boiler 1 Boiler 2
Voltage
Modulating
Signal Outputs
Outdoor Sensor
System Sensor
Prove Jumper
Do Not remove
Shield Shield
L
N
System Pump
L
N
Modulating
Condensing
Group (Boiler 1 & 2) {
Staging
Non-Condensing
Group (Boiler 3 & 4) {
Boiler 1 Boiler 2
Staging Voltage
Signal Outputs

The TempTracker mod+ Hybrid can modulate any combination of current or voltage boiler signals. The Modulating
Output Type must be set to match the boiler modulating signal before connecting any output wires to avoid
damaging components. See "Modulating Output Type" on page 24. Some modulating boilers may require the use of
the stage output relay in addition to the modulating output.

The Modulating Output Type must be set to match the boiler modulating signal
prior to wiring the boiler signal to avoid control or equipment damage.

TempTracker mod+ Hybrid Installation and Operation Manual 15
HTC# 059105-00D

(A Terminals 13, 14), (B Terminals 16, 17),...
• The TempTracker mod+ Hybrid can operate up to four 4-20 mA modulating motors.
• The Extension can operate up to six 4-20 mA modulating motors.
• The TempTracker mod+ Hybrid and the Extension sources excitation voltage for the 4-20mA signal.
• Wire the (-) from the boiler modulating motor to the (GND) terminal on the TempTracker mod+ Hybrid. That is
for boiler A, the modulating (GND) terminal will be 13.
• Wire the (+) from the boiler modulating motor to the (mA+) terminal on the TempTracker mod+ Hybrid. That is
for boiler A, the modulating (mA+) terminal will be 14.
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12
13 15
14
17
16
18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-
+
+
mA
GND
VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Boiler 4-20mA
Modulation Output
4-20mA
Burner
Motor
-+
OD=55oF SYS=142oF
 <A> B
 80% 50%
STAGE◄►MENU


(A Terminals 13, 15), (B Terminals 16, 18),...
• The TempTracker mod+ Hybrid can operate up to four 0-10V modulating motors.
• The Extension can operate up to six 0-10V modulating motors.
• Wire the (GND) from the boiler modulating motor to the (GND) terminal on the TempTracker mod+ Hybrid. That
is for boiler D, the modulating (GND) terminal will be 22.
• Wire the (VLT+) from the boiler modulating motor to the (VLT+)terminal on the TempTracker mod+ Hybrid.
That is for boiler D, the modulating (VLT+) terminal will be 23.
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18
20
19
21 24
23
29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-
+
+
mA
GND
VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
Boiler Voltage
Modulation Output
Voltage
Burner
Motor
GND V+

16 Raypak, Inc.
HTC# 059105-00D


To set the Extension to a specic letter, remove the wiring cover and switch the Ext A/Ext B
to the desired letter. DO NOT set both extensions to the same letter to avoid errors.
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION
MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O
L
N
P
1514
VLTmA
CUR / VLT
181716
VLTmAGND
CUR / VLT
212019
VLTmAGND
CUR / VLT
242322
VLTmAGND
CUR / VLT
J
11 12
K M OL N P
E F G H
K ML N
13
GND
16
GND
19
GND
22
GND
2726
VLTmA
CUR / VLT
302916
VLTmAGND
CUR / VLT
25
GND
28
GND
I J
O P
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
120VAC Power
Six N.O. Boiler startup relay
outputs. Each is wired in series
with the boiler's limit circuit.
Six modulating outputs can be 4-20mA or voltage.
Go to TempTracker mod+ Hybrid Startup Menu to
determine the type of output for each stage.
LED indicates the
associated relay status.
Connect to any TempTracker mod+ or Hybrid
and additional Extension panels to add
additional stages using a RJ11 cable only
(cable provided with TempTracker mod+ Ext).
Extension Selection Switch to determine
Stage letters and LED colors.
Ext-A Stages E - J and all LEDs are Green
Ext-B Stages K - P and all LEDs are Red
This switch is covered with the Wiring Enclosure.
HYBRID
• The TempTracker mod+ Hybrid is equipped with a RJ45 socket and a RJ45 to RJ11 Adaptor to connect to extension
panels (#013179F) and 4-20mA EMS Interfaces (#012019). The Extension is equipped with two RJ11 sockets and a
RJ11 cable to connect to TempTracker mod+ Hybrid and an additional Extension. Use the RJ45 to RJ11 Adaptor on the
TempTracker mod+ Hybrid.
• The order in which the control, the extensions, and the interface are wired is not observed.
• Set each Extension to a different letter (EXT-A or EXT-B). The TempTracker mod+ Hybrid will assign the stage letters based on
the extension letter selected.
• Extension A will operate stages (E - J) and all the LEDs will be Green. However, Extension B will operate stages (K - P) and all
the LEDs will be Red. .
• Congure the Modulating and Sequencing Output Types after connecting the Extension panels to be able to congure their outputs.
See "Boiler Type" on page 20
• Only the 6-wire RJ11 cable supplied with the extension must be used for proper operation.
• RJ11 cables must be of a 6-wire with 6-pin terminals.
TempTracker mod+ Hybrid
connected to Two Extension Panels
and 4-20mA EMS Interface
TempTracker mod+ Extension ATempTracker mod+ Hybrid
TempTracker mod+ Extension B
Each Extension Panel or 4-20mA EMS
Interface comes with Connection Cable.
RJ11
RJ45
RJ45 to RJ11
Adaptor
RJ11
RJ11
4-20 mA EMS
4-20mA INPUT
+Signal GND
123
RS485
EXTENSION
CONNECTORS
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION
MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O
L
N
P
1514
VLTmA
CUR / VLT
181716
VLTmAGND
CUR / VLT
212019
VLTmAGND
CUR / VLT
242322
VLTmAGND
CUR / VLT
J
11 12
K M OL N P
E F G H
K ML N
13
GND
16
GND
19
GND
22
GND
2726
VLTmA
CUR / VLT
302916
VLTmAGND
CUR / VLT
25
GND
28
GND
I J
O P
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION
MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O
L
N
P
1514
VLTmA
CUR / VLT
181716
VLTmAGND
CUR / VLT
212019
VLTmAGND
CUR / VLT
242322
VLTmAGND
CUR / VLT
J
11 12
K M OL N P
E F G H
K ML N
13
GND
16
GND
19
GND
22
GND
2726
VLTmA
CUR / VLT
302916
VLTmAGND
CUR / VLT
25
GND
28
GND
I J
O P
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA

TempTracker mod+ Hybrid Installation and Operation Manual 17
HTC# 059105-00D

• The TempTracker mod+ Hybrid can communicate to BACnet MSTP networks when used the BACnet Interface Module (#651735).
The module must be purchased separately.
• The BACnet Interface Module comes with an RJ45 cable.
• Both the TempTracker mod+ Hybrid and the BACnet Interface Module (#651735) are equipped with a RJ45 socket (RS485) to
connect to communicate to each other.
• The Interface BACnet Module must be wired to the BACnet MSTP network using the RS485 terminals A, GND, and B.
• If both an extension panel and the BACnet Interface Module are to be used, connect the RJ11 socket on the BACnet Interface
Module to the extension.
• Set the BACnet parameters. See "BACnet MSTP Startup Menu" on page 27.
BACnet Interface Module
MSTP
1 2 3
A GND B PRODUCT
COMM RS485
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN
-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR
CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION : RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID
RJ45 Communication Cable
RJ45 Cable
Extension
RJ11 Extension Cable
F
H
J
Power
CAUTION: Risk of Electric Shock.
More than one disconnect switch may be required
to de-energize the equipment before servicing.
PWR
L N
1 2
E
3 4
F
5 6
G
7 8
H
9 10
I
11 12
EXTENSION
MODULE
RS-485
Ext A
INPUT RATINGS:
115VAC 60Hz, 12VA MAX
Use Copper Conductors Only.
OUTPUT RATINGS:
120VAC, 6A RESISTIVE
1A PILOT DUTY, 15A TOTAL
FOR ALL CIRCUITS
E
G
I
Comm
Ext B
K
M
O
L
N
P
1514
VLTmA
CUR / VLT
181716
VLTmAGND
CUR / VLT
212019
VLTmAGND
CUR / VLT
242322
VLTmAGND
CUR / VLT
J
11 12
K M OL N P
E F G H
K ML N
13
GND
16
GND
19
GND
22
GND
2726
VLTmA
CUR / VLT
302916
VLTmAGND
CUR / VLT
25
GND
28
GND
I J
O P
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
RJ45
RJ11
RJ45 RJ11
A (+)
Ground
B (-)
To BACnet
MSTP

18 Raypak, Inc.
HTC# 059105-00D

--------SETTINGS----
Season Winter
SystemTarget140oF
<SystemSettings>
<Maintenance>
<SystemStartup>
BACK▲▼SELECT
--AREYOUSURE?--
No
Yes
BACK▲▼SAVE
---SENSORTYPE---
ResetoF
ResetoC
4-20mAEMS
BACK▲▼SAVE
-SWITCHSETPOINT-
150oF
[ ]
BACK▲▼SAVE
---SWITCHDIFF---
10oF
[ ]
BACK▲▼SAVE
---SWITCHDELAY---
0.5Hour
[ ]
BACK▲▼SAVE
HEAVYLOAD
-SEQUENCE#2GROUP-
No
Yes
BACK▲▼SAVE
CONDENSING
----BOILERTYPE----
Modulating
Staging
BACK▲▼SAVE
CONDENSING
--BOILERNUMBER--
2
[ ]
BACK▲▼SAVE
CONDENSING
-MODULATINGMODE-
Normal
Parallel
BACK▲▼SAVE
NON-CONDENSING
----BOILERTYPE----
Modulating
Staging
BACK▲▼SAVE
PROVE/DHWSHARING
Prove
DHWPriority
DHWNoPriority
NoPriority(Summer)
BACK▲▼SAVE
-DHWSETPOINT-
180oF
[ ]
BACK▲▼SAVE
-SETBCK/SHUTDOWN-
Shutdown/Disable
Tstat/Enable
Setback
BACK▲▼SAVE





CONDENSING
--OUTPUTATYPE--
4-20mA
0-10volt
1-10vCustom
BACK▲▼SAVE
---BOILERTYPE---
Modulation
Staging
Hybrid
BACK▲▼SAVE
-EMS4maSETPOINT-
70oF
[ ]
BACK▲▼SAVE
-EMS20maSETPOINT-
220oF
[ ]
BACK▲▼SAVE


---BOOSTMODE---
30Minutes
Disable
BACK▲▼SAVE
---SENSORFAULT---
AllOff
AllOn
BACK▲▼SAVE
NON-CONDENSING
--BOILERNUMBER--
1
[ 
]
BACK▲▼SAVE
CONDENSING
--OUTPUTBTYPE--
4-20mA
0-10volt
1-10vCustom
BACK▲▼SAVE
NON-CONDENSING
--OUTPUTCTYPE--
4-20mA
0-10volt
1-10vCustom
BACK▲▼SAVE
NON-CONDENSING
-MODULATINGMODE-
Normal
Parallel
BACK▲▼SAVE
Yes

---BACNETMODE---
Disable
Enable
BACK▲▼SAVE





  

  

 
 

TempTracker mod+ Hybrid Installation and Operation Manual 19
HTC# 059105-00D
-EMSINPUTMODE-
Disable
Enable
BACK▲▼SAVE
-EMS4maSETPOINT-
70oF
[ ]
BACK▲▼SAVE
-EMS20maSETPOINT-
220oF
[ ]
BACK▲▼SAVE


To be able to change the
TempTracker mod+ Hybrid settings the
Program/Run Switch must be set to
Program. The switch is located under the
Enclosure Wiring Cover for security. The
Enclosure Wiring Cover can be secured
using a lock.
--------SETTINGS----
Season Winter
SystemTarget140oF
<SystemSettings>
<Maintenance>
<SystemStartup>
BACK▲▼SELECT
--AREYOUSURE?--
No
Yes
BACK▲▼SAVE
PROVE/DHWSHARING
Prove
DHWPriority
DHWNoPriority
NoPriority(Summer)
BACK▲▼SAVE
-DHWSETPOINT-
180oF
[ ]
BACK▲▼SAVE
-SETBCK/SHUTDOWN-
Shutdown/Disable
Tstat/Enable
Setback
BACK▲▼SAVE
---BOOSTMODE---
30Minutes
Disable
BACK▲▼SAVE
---SENSORFAULT---
AllOff
AllOn
BACK▲▼SAVE

---BOILERTYPE---
Modulation
Staging
Hybrid
BACK▲▼SAVE
--SENSORTYPE--
ResetoF
ResetoC
SetPointoF
SetPointoC
BACK▲▼SAVE



--BOILERNUMBER--
2
[ ]
BACK▲▼SAVE
--OUTPUTTYPE--
On/Off
2-Stage
3-Stage
4-Stage
BACK▲▼SAVE
-STAGINGMODE-
LO/HI/LO/HI
LO/LO/HI/HI
BACK▲▼SAVE

--OUTPUTATYPE--
4-20mA
0-10volt
1-10vCustom
BACK▲▼SAVE
--BOILERNUMBER--
2
[ ]
BACK▲▼SAVE
-MODULATINGMODE-
Normal
Parallel
BACK▲▼SAVE



---BACNETMODE---
Disable
Enable
BACK▲▼SAVE







 


 
 

20 Raypak, Inc.
HTC# 059105-00D


To be able to change the TempTracker mod+ Hybrid settings the Program/Run Switch must be
set to Program. The switch is located under the Enclosure Wiring Cover for security.
SYSTEM
A
B
C
D
12
RUNPROGRAM
DO NOT APPLY ANY VOLTAGE
TO INPUT TERMINALS
345678910 11 12 13 15
14 17
16 18 20
19 21 24
23 29
25 27
26 28 32
30 31
LN-+
+
TT
OORS-485
mA
GND VLT
SYS ABCD
PWR CUR / VLT
A
-+
+
mA
GND VLT
-+
+
mA
GND VLT
+
+
mA
22
-
GND VLT
+
mA
TEMP
OUTDOOR
OO
TEMP
SYSTEM
EXTENSION
MODULE
CUR / VLT
B
CUR / VLT
C
CUR / VLT
D
PROVE
/DHW
SHUTDOWN
/SETBACK
FOR ALL CIRCUITS
120VAC, 6A RESISTIVE
OUTPUT RATINGS:
1A PILOT DUTY, 15A TOTAL
115VAC 60Hz , 30VA MAX
INPUT RATINGS:
USE COPPER WIRE,
CLASS 1 WIRE ONLY.
CAUTION: RISK OF ELECTRIC SHOCK
More than one disconnect switch may be required
to de-energize the equipment before servicing.
ENCLOSED
ENERGY
MANAGEMENT
EQUIPMENT
99RA
/TSTAT
HYBRID

Button: MENU/<System Startup>
• When powered, the TempTracker mod+ Hybrid performs a self diagnostics-test.
• On the rst power up, the System Startup screen will appear after the initialization is
complete. If it doesn’t, the TempTracker mod+ Hybrid has already been congured.
• The System Startup menu sets the main parameters that relate to the heating application.
These settings must be set by the installer.
--------SETTINGS----
Season Winter
SystemTarget140oF
<SystemSettings>
<Maintenance>
<Histories>
<SystemStartup>
BACK▲▼SELECT

Modulation,Staging,Hybrid Default:Modulation
Button: MENU/<System Startup>/..../Boiler Type
• The same Raypak control can operate modulating boilers, staging boilers, or a combination
of both types.
• The Modulation option will operate a variety of modulating boilers.
• The Staging option will operate a variety of On/Off or multi-stage boilers.
• The Hybrid option will sequence two groups of boilers, condensing and non-condensing.
Each group could be of a different boiler type (Modulation or Staging). See "HYBRID
Startup Settings" on page 21. Each Multi-Stage boiler will use a single output relay. The
staging will take place using the voltage output signal.
• If BACnet is to be used, each of the Boiler Type modes will have a different set of BACnet
variables. See "Hybrid - Outdoor Reset - BACnet Variable list" on page 44..
---BOILERTYPE---
Modulation
Staging
Hybrid
BACK▲▼SAVE

Reset°F,Reset°C,SetPoint°F,SetPoint°C,4-20mAEMS Default:Reset°F
(Set Point Options Not Available with Hybrid Boiler Type)
Button: MENU/<System Startup>/..../Sensor Type
• If Reset °F is selected, all temperatures and settings will be displayed in degrees Fahrenheit
and the control will use Reset Ratios to adjust the system set point.
• If Reset °C is selected, all temperatures and settings will be displayed in degrees Celsius and
the control will use Reset Ratios to adjust the system set point.
• If Set Point °F is selected, all temperatures and settings will be displayed in degrees
Fahrenheit and the control will have an adjustable system set point.
• If Set Point °F is selected, all temperatures and settings will be displayed in degrees Celsius
and the control will have an adjustable system set point.
• The 4-20mA EMS option is only available to the Hybrid Boiler Type option. To use
4-20mA EMS with Staging and Modulating Boiler Types, select one of the Set Point options
and the EMS Input Mode menu will follow to offer the 4-20mA EMS option.
• The use of the 4-20mA EMS option requires the purchase of the 4-20mA EMS Interface
(#012019). It gives the TempTracker mod+ Hybrid the capability of accepting a remote
4-20mA signal from a BMS or EMS system as the target set point.
• If BACnet is to be used, each of the Sensor Type modes will have a different set of BACnet
variables. See "Hybrid - Outdoor Reset - BACnet Variable list" on page 44..
--SENSORTYPE--
ResetoF
ResetoC
SetPointoF
SetPointoC
BACK▲▼SAVE
---SENSORTYPE---
ResetoF
ResetoC
4-20mAEMS
BACK▲▼SAVE

Disable,Enable Default:Disable
(Available after Set Point with Staging or Modulation Boiler Types)
Button: MENU/<System Startup>/..../Boiler Type/Sensor Type / EMS Input Mode
• It allows the TempTracker mod+ Hybrid to utilize the 4-20mA EMS Interface (#012019) to
accept a remote 4-20mA signal from a BMS or EMS system as the target set point.
-EMSINPUTMODE-
Disable
Enable
BACK▲▼SAVE