Rayrun P10 User manual

Single Color LED Controller
Wireless Remote ControlModel: P10(-S)Full ProtectionHigh PowerWireless RemoteWaterproofCompact SizeWide Voltage RangeP10 single color LED controller is designed to drive constant voltage LED products in voltage range of DC5-24V. The main unit works with a RF remote controller, user can setup LED brightness and dynamic modes on the remote controller. The main unit is powered by DC power supply and receives remote controller commands to drive LED fixtures.Introduction1. Power supply inputWiring & IndicatorThe controller supply voltage range is from DC 5V to 24V. The red power cable should be connected to power positive and black to negative. (For other cable color, please refer to the labels). The LED output voltage is at same level as the power voltage, please make sure the power supply voltage is correct and the power rating is capable for the load. 2. LED outputConnect constant voltage LED loads. Please connect red cable to LED+ and black cable to LED-. Please make sure the LED rated voltage is same as the power supply and each channel’s maximum load current is in range of the controller rated current.3. Work status indicatorThis indicator shows all working status of the controller. It displays different events as following:Steady blue: Normal working.Short white blink: Command received.Long single white blink: Mode cycle edge.Single yellow flash : Edge of the content.Red flash: Overload protection.Yellow flash: Overheat protection.White blink for 3 times: New remote paired.Please connect the controller output to LED loads and power supply to the controller power input. The power supply voltage must be same as the LED load's rated voltage. Check all cables to be well connected and insulated before power on.To 110/230 AC power5-24V DC outputPower supplyP10 LED ControllerConstant voltageLED loadRemoteController5-24V DC5-24V Driving5. Turn ON / OFFPress ‘I’ key to turn on unit or press ‘O’ key to turn off. Controller will memorize the on/off status and will restore to the previous status on next power on.Please use remote controller to turn on the unit if it was switched to off status before previous power cut.Functions84. Wiring diagram6. Brightness controlPress ‘+’ key to increase brightness and press ‘-’ key to decrease. There are 4 brightness shortcut key to set brightness to 100%, 50%, 25% and 10% of full brightness. The controller applies brightness gamma correction on dimming control, makes the brightness tuning more smooth to human sense. The brightness shortcut level is valued to human sense, and not proportional to the LED output power.Pair newremotePress within 10seconds afterreceiver powered on

7. Dynamic mode and speed controlThese keys control the dynamic modes. Press key to select dynamic modes and press key to set the running speed of the dynamic modes.User could set multiple dynamic modes including SOS signal and flame effects.MODEMODE8. Remote indicatorThis indicator blinks when remote controller works. The indicator will flash slowly if the battery is empty, please change the remote controller battery in this case. The battery model is CR2032 lithium cell.You could pair a new remote controller to main unit by following steps:1). Plug off the power of main unit and plug in again after more than 5 seconds.2). Press and key simultaneously for about 3 seconds, within time of 10 seconds after the main unit powered on.11. Recognize current remote onlyIn some cases, one main unit might be paired with several remote controllers but extra remote controllers are no longer needed. User could simply pair the current using remote to main unit again, then the main unit will dis-pair all other remote controllers and recognize current one only.Advanced features12. Waterproof (-S version)The IP-68 waterproof feature with glue injection finish is available on -S version controllers. For overall waterproof performance, the cables must be waterproof treated separately.Wireless signal degrade : The wireless communication ability could degrade when using at wet environment, please be aware that the wireless control distance will be shortened in such case. 13. Protection functionThe controller has full protection function against wrong wiring, load short circuit, overload and overheat. The controller will stop working and the indicator will flash with red / yellow color to indicate the malfunction. The controller will try to recover from protection status in a short time when the working condition is good.For protection issues, please check the situation with different indicator information:Red flash: Check the output cables and load, make sure no short circuit and the load current is in rated range. Also the load must be constant voltage type. Yellow flash: Check the installation environment, make sure in a rated temperature range and with good ventilation or heat dissipation condition.
Model
P10
P10-S
Brightness grade
10 levels
Brightness shortcut
4 levels
Dynamic mode
8 modes
Dynamic speed grade
10 levels
PWM grade
4000 steps
Overload protection
Yes
Overheat protection
Yes
Working voltage
DC 5-24V
Remote frequency
433.92MHz
Remote control distance
>15m at open area
Rated output current
1x15A
IP Grade
IP63
IP68
Specification9. Using the remotePlease pull out the battery insulate tape before using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts.10. Paring a new remote controllerThe remote controller and main unit is 1 to 1 paired for factory default. It’s possible to pair maximum 5 remote controllers to one main unit and each remote controller could be paired to any main unit.Operation

P10LED5V单⾊控制器⽤来驱动电压范围为到24VLEDLEDLED的灯带或模块等恒压灯具。⽤⼾可以通过卡⽚式射频控制器来调节灯具的亮度和动态LED模式。控制器需要直流电源供电，并根据接收到的遥控器指令驱动LED灯具，实现亮度和动态模式调节功能。简介安装1.电源输⼊控制器可接受电压为5V到24V的直流电源供电，请将红⾊电缆线连接到电源的正极，⿊⾊电缆线连接到电源的负极。请确保LED灯具的额定电压与电源电压相同，且电源的功率满⾜控制器和灯具的需求。为保证安全，在通电前请先确保所有电缆均已可靠连接且绝缘良好。2.LED输出连接到LED灯具。LED灯具必须为恒压型且适⽤于PWM驱动。请将红⾊电缆线连接到LED灯具的正极，⿊⾊电缆线连接到LED灯具的负极，请确保LED的额定电压与电源相同，并且最⼤负载电流在控制器的额定电流范围内。型号:P10(-S)3.状态指⽰灯该指⽰灯显⽰控制器的⼯作状态，指⽰灯与控制器⼯作状态和对应关系如下：蓝⾊常亮：正常⼯作⽩⾊单闪：收到命令⽩⾊慢闪：模式循环边缘⻩⾊慢闪：达到亮度或速度极限红⾊闪烁：过载保护⻩⾊闪烁：过热保护⽩⾊闪烁3次：新遥控器配对成功请将控制器输出与LED恒压灯具相连接，并将控制器输⼊与电源相连接。LED电源电压需与恒压灯具的额定电压相同。请在通电前检查所有电缆连接是否正确。4.接线图解5-24VDC接交流电5-24V直流电源LED控制器LED恒压灯具RF遥控器功能85.开关按“I”键开启灯光，按“O”键关闭。控制器会记忆断电前的开关状态，如果在断电前处于关机状态，下次通电后请使⽤遥控器开灯。RF⽆线遥控单⾊LED控制器配对新遥控器控制器通电后10秒钟内同时按下全功能保护高功率无线遥控防水功能小尺寸宽电压输入

⾼级功能遥控器操作⽅法9.使⽤遥控器使⽤前请拔出遥控器电池绝缘⽚。RF⽆线遥控信号可以穿过⼀定的⾮⾦属屏障，为了保证控制器的接收效果，请勿将控制器安装在有⼤⾯积⾦属遮挡的位置。10.与新遥控器配对遥控器和控制器出⼚默认为1对1的配对状态。1个控制器最多可配对5个遥控器，⽽遥控器可配对任意的控制器。如需配对新的遥控器，请按以下两个步骤操作：1）断开控制器电源，并在超过5秒以后重新通电。2）控制器通电后10秒内，同时按下新遥控器键约3秒钟。配对成功后,控制器指⽰灯将闪烁3次提⽰配对完成。11.保留当前遥控器并清除其他遥控器在控制器已与多个遥控器配对、⽽仅想保留当前遥控器的情况下，可以将正在使⽤的遥控器与控制器再进⾏⼀次配对操作，此后控制器将清除其他已配对的遥控器⽽仅保留当前使⽤的控制器。
13.保护功能
型号
P10
P10-S
亮度可调级数
10级
亮度快捷选项
4级
动态模式
8种
速度可调级数
10级
PWM分辨率
4000级
过载保护
有
过热保护
有
⼯作电压
DC5-24V
遥控器⼯作频率
433.92MHz
遥控器⼯作距离
空旷地带>15⽶
额定输出电流
15A
防⽔等级
IP-63
IP-68
规格6.亮度调节按键增加亮度，按键降低亮度。亮度快捷键分别有全亮度的100%、50%、25%和10%。控制器在调光控制上应⽤伽玛校正原理，使亮度调节更顺滑，更符合⼈眼的视觉感觉，它与LED输出功率不成正⽐。8.遥控器指⽰灯按下遥控器按键时，该指⽰灯会快速闪烁。如果指⽰灯慢闪，则说明遥控器电池电量已耗尽，请更换遥控器电池（CR2032型纽扣电池）。7.动态模式与速度调节按和调节动态模式，按和键调节动态模式的运⾏速度。MODEMODE12.IP68防⽔(-S版本)后缀为-S版本的控制器应⽤了注胶防⽔⼯艺，可以达到IP68的防⽔等级。为了确保整体的防⽔效果，需要对输⼊输出电缆做单独的防⽔处理。请注意：在浸⽔环境下，控制器的⽆线接收性能会下降，遥控器的控制距离会缩短甚⾄⽆法控制。本产品具有完善的保护功能，可以最⼤程度的防⽌因接线错误、负载短路、过载或过热⽽引起的产品损坏。当发⽣以上异常状态时控制器将停⽌⼯作，同时指⽰灯会闪烁红⾊或⻩⾊。当⼯作状态良好时，控制器会尝试恢复正常⼯作。当控制器停⽌⼯作时，请检查指⽰灯的状态，在不同的闪烁状态下应检查相应的故障：红⾊闪烁：请检查输出电缆是否短路、负载电流是否过⾼，并且请确保所驱动灯具为恒压驱动类型。⻩⾊闪烁：请检查控制器的安装环境以及负载功率，并确保控制器散热条件良好且负载功率在额定范围之内。