Rayrun Umi Smart User manual

Wall panel touch remote controller
BW03-C(A/B)
Battery:
CR2032
General Purpose
Battery / AC power
Group / Scene
Open the wall panel
with a screw driver.
Battery version:
Pull out battery
insulation tape.
AC version: Connect AC power
and install bottom part to
socket with screw, then clip
panel part to bottom part.
Battery version: Install the
back cover to wall with
screw or adhesive, then clip
panel part to the back cover.
Battery version
Quick installation guide
Remove
before use
This touch wall panel is designed to control compatible Single color, CCT, RGB,
RGB+White or RGB+CCT LED controllers, drivers or lighting fixtures via Umi wireless
protocol. There are two power supply options with AC power or cell battery. The AC version
can fit traditional wall installation with AC power and the battery version can be easily
installed at any preferred place.
Introduction
1 2
34
1. Open the touch panel
The wall panel needs to be opened before installation. Please use a slot type screw
driver to twist in the bottom side slot and open the panel. Please refer to picture 1.
AC version installation
2. Connect the AC power
Push the top of connector on the bottom part back and insert the L and N AC power
2
cables. The maximum cable gauge is 1.5mm or AWG16.
CAUTION! Cut off the AC power before installation to avoid electric shock!
1. Open the touch panel
The wall panel needs to be opened before installation. Please use a slot type screw
driver to twist in the bottom side slot and open the panel. Please refer to picture 1.
2. Prepare the battery
For new wall panel, please pull out the insulation tape under the battery. To change
the battery please slide the battery out from the battery socket and insert a new one. The
battery type is CR2032. Please refer to picture 2.
3. Install the panel
Install the back cover to preferred place by screw or double side adhesive tape, then
clip the front panel part to the back cover and finish the installation. Please refer to
picture 4.
3. Install the panel
Install the bottom part to wall socket with screws. After the bottom part is installed,
clip the front panel part to the bottom part to finish the installation. Please refer to
picture 3.
Battery version installation
AC
version
Umi Smart Wireless

4. Pair / unpair the wall panel to receiver
The wall panel needs to be paired to receiver to work. User can pair up to 5 wall
panels to one receiver and each wall panel can be paired to any receiver.
To pair or unpair wall panel to the receiver, please operate with following steps:
1). Cut off the power of receiver and power on again after more than 5 seconds.
2). Touch and key simultaneously and briefly within 10 seconds after receiver
powered on.
3). Release all keys, then touch key or 1-4 digit key within 10 seconds to pair the
panel to receiver. For key, the receiver will be paired without group feature, for 1-4
key the receiver will be paired to 1-4 target group.
4). To unpair the panel from receiver, do the step 1-2 first, then release all keys and
press key within 10 seconds.
Operation
Turn on/off lights.
Touch to activate color
changing. Double
click to change color
mixing mode.
Touch to activate group
function for digit keys.
The beeper will sound
twice when in group
mode.
At scene mode: click
to recall the scene,
hold press to save
current status to the
scene position.
At group mode:
select destination
group, only current
group member will
response to the
panel after
selection.
Function
Switch group mode to
all members. All
paired receivers will
response to the panel
after touching this key.
Dimming / Changing color. Slide
upward or downward to increase or
decrease brightness / color. Touch the
top or bottom section to jump to
maximum or minimum value.
6. Slider and shortcut key
The default function for the slider is dimming, user can slide up or down or adjust
brightness step by step or slide and hold to adjust continuously. When key is
touched, the slider function will swap to color adjust shortly and the operation method
is same as brightness adjusting.
The top and bottom section of the slider is shortcut key to max or min value. For
brightness adjusting, touch the slider top section will jump to maximum brightness and
touch the bottom section will jump to the minimum.
Specification
AC version working voltage
Battery version working voltage
Wireless protocol
Frequency band
Wireless power
Working temperature
Panel dimension
AC90-265V
DC3V, CR2032 battery
Umi protocol based on SIG BLE Mesh
2.4GHz ISM band
< 7dBm
-20-55 C(-4-131 F)
86x86x10mm (Europe standard)
t
a
p
y
s
a
E
f
f
o
/
n
o
7. Easy pat on/off
For the most frequently used turn on and off function, besides touching the on/off
key, user can also pat on the panel with whole palm, this gesture will also turn on/off
the lights. The pat operation is more convenient for daily use.
5. Change RGB/White mixing mode
Double click the key to change color mixing mode.
For RGB+White and RGB+CCT application, the color mixing mode can be switched
between white(CCT), RGB and White(CCT)+RGB mode.
9. Switch target group
To switch the target group, please press the key first, then press the target
group digit key. For example, to switch to group one, please press then key. The
wall panel function will switch to the target group shortly. To restore the remote
controller to all groups, please press key.
8. Load and save scenes
The default function of 1-4 digit keys are for scene function. User can short press 1-4
key to load scene. To save a scene, please adjust the favorite light status first, then hold
press 1-4 digit key to save current status to relative scene position. After save operation,
user can load the saved scene by short press the digit key.
10. Turn ON/OFF beep sound
A beeper is equipped in the panel and the beep sound is ON as default. To turn on/off
the beeper sound, please hold press the key for about 1 second, the beeper on/off
status will swap.

BW03-C(A/B)
简介
1 2
34
快速安装指南
电池:
CR2032
电池版本:
移除电池绝缘⽚
电池版
交 流 电 版
交流供电版本的安装⽅法
电池版本的安装⽅法
使⽤前
移除
墙⾯触摸遥控器
Umi智能⽆线
⽤螺丝⼑打开⾯板
交流电版本：连接交流电源
并⽤螺钉将底壳安装到墙⾯
接线盒，然后将⾯板卡到底
壳上。
电池版:⽤螺钉或双⾯胶将
后盖安装到墙上，然后将⾯
板卡到后盖上。
本触摸⾯板可以通过Umi⽆线协议控制兼容的单⾊、CCT、RGB、RGBW或
RGBCCTLED控制器、驱动电源或其他照明设备。本产品有交流供电和纽扣电池
供电的两种版本可供选择，交流电版本可安装在有零⽕线供电的墙⾯接线盒上，
电池版本则可以安装在任何需要的位置。除了基本的开/关和调光功能外，本产
品还可⽤于多通道灯具，⽤来调整颜⾊和多通道混合模式。
1.打开⾯板
安装前需要先打开本产品。请使⽤⼀字型螺丝⼑插⼊底部侧槽并旋转螺丝
⼑来撬开⾯板。请参考图1。
2.连接交流电
按下底部接线座的塑料按钮，并接⼊交流电零线和⽕线。电缆的最⼤尺⼨为
2
1.5mm 。
警告！在安装前请切断交流电源，以免触电！
3.安装⾯板
⽤螺钉将⾯板底部安装到墙⾯接线盒，然后将⾯板上部卡⼊。请参考图3。
2.纽扣电池
新产品在初次使⽤时请拔出电池下⽅的绝缘⽚。如果要更换电池，请将电池
从电池插槽中推出并更换，电池为CR2032型纽扣电池。请参考图2。
3.安装⾯板
⽤螺钉或双⾯胶将后盖安装到墙上，然后将⾯板卡到后盖上。请参考图4。
1.打开⾯板
安装前需要先打开本产品。请使⽤⼀字型螺丝⼑插⼊底部侧槽并旋转螺丝
⼑来撬开⾯板。请参考图1。

⾯板需要与灯具或控制器配对才能⼯作。⼀个灯具或控制器最多可以配对5个⾯
板或各类遥控器，⾯板则可以与任意匹配灯具或控制器配对。
请按以下步骤操作来完成⾯板配对或取消配对：
1).将⽬标灯具或控制器断电，在超过5秒后再通电。
2).在灯具或控制器通电后的10秒内，同时触摸⾯板上的与键。
3).松开所有键，然后在10秒内按键或1到4任意数字键。如果按键，灯具
或控制器会与⾯板配对但不会被分配到任何分组；如果按1到4号数字按键，灯具或控
制器会与遥控器配对且被分配到相应数字的分组。
4).若要取消⾯板与控制器的配对，请先执⾏步骤1-2，然后松开所有键并在10秒
内按下键。
4.配对到灯具或控制器
操作⽅法
开/关
轻触激活颜⾊调整，
双击更改RGB与⽩光
混合模式。
轻触激活分组选择。
激活分组选择时，会发
出两声提⽰⾳。
场景模式下（默认）：
点击调⽤场景，⻓按
保存当前状态到场景
位置。
分组模式下：选择分
组后只有⽬标群组会
响应⾯板操作。
功能
从分组模式切换到全体
模式。按此键后，所有已
配对的灯具/控制器均会
响应本⾯板。
调光/调⾊：向上或向下滑动调节亮度
/颜⾊。触摸顶部或底部以跳转到最⼤
值或最⼩值。
6.触摸滑条及快捷操作
触摸滑条的默认功能是调光，在触摸键后会短时间切换为颜⾊调整功
能。每上滑或下滑滑条⼀次，亮度或颜⾊会变化⼀级，如果滑动并按住滑条则会
连续调节。
滑条的顶部和底部是最⼤值或最⼩值的快捷键。亮度调节时，触摸滑块顶
部将跳转到最⼤亮度，触摸底部将跳转到最⼩亮度。
7.掌拍开关
对于最常⽤的开关灯操作，除了触摸⾯板开关键以外，⽤⼾还可以⽤整个
⼿掌在⾯板上轻拍，这个⼿势可以更便捷的打开/关闭灯光。
5.更改RGB/⽩⾊混合模式
双击键可更改颜⾊混合模式。
对于RGBW和RGB+CCT控制器，混⾊模式可以在⽩⾊（CCT）、RGB和⽩⾊
（CCT）+RGB模式之间切换。
掌拍
开关
8.调出和保存场景
1-4数字键的默认功能为场景功能。⽤⼾可以轻触1-4键调出已保存的场景。
若要保存场景，请⻓按1-4数字键将当前灯光效果保存到相应的场景位置。保存场
景后，可以通过轻触数字键调出保存的场景。
9.切换⽬标群组
要切换分组，请先按键，然后随即按⽬标组数字键。例如，要切换到第⼀组，请
按再按键，遥控器的所有控制功能将切换到分组1。要将遥控器切换到所有灯
具或控制器，请按下键。
10.打开/关闭操作提⽰⾳
本产品的操作提⽰⾳默认为打开状态，如果想切换提⽰⾳的开关状态，请按
开关键约1秒钟来关闭或打开提⽰⾳。
规格
交流版⼯作电压
电池版⼯作电压
⽆线协议
频段
发射功率
⼯作温度
⾯板部分尺⼨
AC90-265V
DC3V,CR2032纽扣电池
Umi协议，基于SIGBLEMesh
2.4GHzISMband
<7dBm
-20-55°C(-4-131°F)
86x86x10mm