Rayrun RQ210 Series User manual

2
Thank you for purchasing our products. RQ210 4-ch RGBW
LED controller is designed to drive constant voltage LED
products with common anode connection in voltage range of
DC6-24V. It contains a main unit and a RF remote controller,
user can setup white brightness or RGB color and brightness
independently, to get flexible mixing of RGB and white or run
color dynamic modes.
4-CH LED Controller
User’s Manual
RQ210 Series
RGBW 4-ch Output
Independent White Control
Full Protection
RF Remote Controller
Waterproof Option
Ultra Slim Design
Dynamic Color Mode
Plenty Preset Color
Introduction
Installing
Functions
1. Turn On/ Standby
Press ‘I’ key to turn on unit or press ‘O’ key to turn off. At power
on moment, unit will automatically restore to previous status
before power cut.
7. Remote Controller Indicator
This blue indicator will blink when remote controller works.
The remote controller works at radio frequency, the signal can
pass through barrier, so it’s not necessary to aim at the
controller when operate the remote.
RF Remote Control
1
2
6
WHITE
MODE
+
MODE
-
WHI TE
COLOR
+
COLOR
-
ONLY
WHI TE
OFF
SPEEDSPEED
-
+
COLOR
5
7
3
4
3. White Brightness
Adjust white LED brightness. Press the right side key to
increase white LED brightness and the left side key to
decrease.
4. Static RGB Color Selection
These keys control the RGB static color.
a) Press color printed keys will set the RGB LEDs to
correspond color light as the key. There are 6 shortcut color
keys to make direct color selection.
b) Press ‘COLOR+’ and ‘COLOR-’ to scroll over all preset static
colors, including the 6 shortcut key colors.
2. White Mode
These two keys control white LED working mode. Press
‘WHITE ONLY’ key, all RGB color will turn off and only white
LED lights up. Press ‘WHITE OFF’ key, the white LED will turn
off and RGB LED remain it’s previous status.
5. Color Brightness
Adjust RGB color brightness. Press the right side key to
increase RGB LED brightness and the left side key to decrease.
6. RGB Dynamic Modes Control
These keys control the RGB dynamic modes.
a) Press ‘MODE+’ and ‘MODE-’ key to select preset dynamic
modes.
b) Press ‘SPEED+’ and ‘SPEED-’ to control the dynamic
mode running speed.
8
9
10
8. Power Supply
The red power cable should be connected to power positive
and black to negative. The controller unit can work from DC
6V to 24V, Please make sure the power supply voltage is
same as the LED load and the power is capable for the load
wattage.

5
6
Specification
9. LED Output
RQ210 supports constant voltage driving LED products with
common anode connection. The black cable on the output
side is the common node, it connects to the power supply
positive inside the controller. The white, green, red and blue
cable runs the driving signal of relevant LED color, please
connect the color cables to the cathode of relevant color LED
loads and the black cable to the common node.
10. Status Indicator
This is a full color status indicator. It displays all working status
of the controller. It indicates different events as following:
Blue: normal working.
Short single white flash: new command executed.
Long single white flash: reach mode or color cycle edge.
Long single yellow flash: reach speed or brightness limit.
Red flash: overload protected.
Yellow flash: overheat protected.
Operation
11. Using Remote
Please pull out the battery insulate tape before using. The RF
wireless remote signal can pass through some nonmetal
barrier. For proper receiving remote signal, please do not
install the controller in closed metal parts.
Please do following steps to pair new remote to RQ210:
1). Plug off the power of RQ210 and plug in again after 5
seconds.
2). Press remote ‘ON’ and ‘White Bright +’ key together in 5
seconds after RQ210 power on, and then press ‘RED’ key in
another 5 seconds.
After this operation, the RQ210 indicator will flash white for
3 times to display the command is accepted, the master unit
now recognizes the new remote. Only 5 latest paired remote
controllers can be recognized by RQ210.
Advanced Features
13. Waterproof
RQ210 is a standard version which can be used in dry
environments. RQ210-S is fully waterproof with IP68
standard, and can be used under water within depth of 30
meters.
Note: The remote receiving sensitivity will decrease when
controller installed in wet environment.
16. Protection
RQ210 series controllers have full protection function for
output short circuit, overload, and overheat. The controller
will automatically recover from protection when working
status is good.
Please ensure the LED loads are in rated range, outputs are
not shorted and the controller unit is in a good heat
dissipation environment to avoid protection.
Model
RQ210
RQ210-S
Dynamic mode
34 modes
Static Color
30 colors
PWM Grade
256 steps
White Brightness Grade
10 levels
Color Brightness Grade
5 levels
Speed Grade
10 levels
Direct Color Select
6 direct keys
Overload protection
Yes
Overheat protection
Yes
Working Voltage
DC 6-24V
Remote frequency
433.92MHz
Remote control distance
>15m at open area
Rated Output Current
3x2.5A + 4A
IP Grade
IP-63
IP-68
12. Pairing New Remote
The remote and RQ210 is 1 to 1 paired as default. Further
more, one master unit can be paired to 5 remote controllers
and every remote can be paired to any master unit.