Rayvision RVH1004 User manual

2010.01.22 411L User Manual V0.6(M02) 1
4CH DVR User Manual
411L v0.6(M02)
This document contains preliminary information and subject to change without notice.

2010.01.22 411L User Manual V0.6(M02) 2
This symbol is intended to
alert the user to the presence
of unprotected “Dangerous
voltage" within the product's
enclosure that may be strong
enough to cause a risk of
electric shock.
This symbol is intended to
alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR
MOISTURE.
NOTE: This equipment has been tested
and found to comply with the limits for a
class digital device, pursuant to part 15 of
the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference
in which case the user will be required to
correct the interference at his own expense.
Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be treated
as household waste. Instead it shall be handed over to the applicable collection point for the
recycling of electrical and electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste handling of this
product. The recycling of materials will help to conserve natural resources. For more detailed
information about recycling of this product, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.

2010.01.22 411L User Manual V0.6(M02) 3
Table of Contents
CHAPTER 1 PACKING DETAIL AND INSTALLATION _____________________ 5
1-1 PACKING ____________________________________________________ 5
1-2 Hard Disk Installation _________________________________________ 6
CHAPTER 2 PANEL LOCATION ________________________________________ 9
2-1 FRONT PANEL CONTROLS ____________________________________ 9
2-2 4CH REAR PANEL CONNECTORS _____________________________ 10
CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS _________________ 11
3-1 LIVE Mode__________________________________________________ 11
3-2 PLAYBACK Mode____________________________________________ 14
3-3 PTZ Mode __________________________________________________ 16
CHAPTER 4 MAIN MENU SETUP ____________________________________ 18
4-1 RECORD SETUP ____________________________________________ 19
4-1.1 Quality & Frame Rate Setup _____________________________ 20
4-2 EVENT SETUP ______________________________________________ 20
4-2.1 MOTION SETUP ________________________________________ 21
4-2.1.1 MOTION AREA SETUP______________________________ 22
4-2.2 SENSOR SETUP ________________________________________ 22
4-3 SCHEDULE SETUP __________________________________________ 23
4-3.1 Schedule Record Setup _________________________________ 24
4-3.2 Holiday Setup __________________________________________ 24
4-4 CAMERA SETUP ____________________________________________ 25
4-5 ACCOUNT SETUP ___________________________________________ 26
4-5.1 Permission Setup _______________________________________ 27
4-5.2 User Picture Setup _____________________________________ 27
4-6 NETWORKING SETUP ________________________________________ 28
4-6.1 NETWORKING SETUP ___________________________________ 28
4-6.1.1 DHCP ____________________________________________ 28
4-6.1.2 LAN ______________________________________________ 29
4-6.1.3 ADSL_____________________________________________ 29
4-6.2 HTTP Setup ____________________________________________ 30
4-6.3 DDNS Setup ___________________________________________ 30
4-6.4 Mail Setup _____________________________________________ 31
4-7 PTZ & RS485 SETUP ________________________________________ 32
4-8 SYSTEM SETUP _____________________________________________ 33
4-8.1 DISPLAY SETUP ________________________________________ 34
4-8.2 DATE/TIME SETUP ______________________________________ 34
4-8.2.1 CHANGE DATE & TIME_____________________________ 35
4-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP _____ 35
4-8.2.3 INTERNET TIME SETUP ____________________________ 36
4-8.3 BUZZER & RELAY SETUP _______________________________ 36
4-8.4 SPOT SETUP___________________________________________ 37
4-9 UTILITY SETUP _____________________________________________ 38
4-10 DIAGNOSTIC _______________________________________________ 39
CHAPTER 5 BACKUP & SEARCH ____________________________________ 40
5-1 BACKUP SETUP_____________________________________________ 40
5-2 SEARCH SETUP_____________________________________________ 41
5-2.1 EVENT SEARCH ________________________________________ 42
5-2.2 TIME SEARCH__________________________________________ 43

2010.01.22 411L User Manual V0.6(M02) 4
CHAPTER 6 Rempte Software Installation and Setup ____________________ 44
6-1 AP Software Installation and instruction _______________________ 44
6-2 How to do remote monitoring through IE ______________________ 46
6-3 AP Software Operation _______________________________________ 47
CHAPTER 7 SPECIFICAITONS_______________________________________ 48
CHAPTER 8 MOBILE APPLICATION INSTALLATION AND USAGE__________ 50
8-1 Mobile Application Installation and Operation for Symbian System 50
8-1.1 Mobile Application Installation____________________________ 50
8-1.2 Mobile Application Operation_____________________________ 51
8-1.2.1 Add New Login DVR _______________________________ 51
8-1.2.2 Logging Onto the DVR _____________________________ 51
8-1.2.3 Modify the Login Information of DVR ________________ 52
8-1.2.4 Delete the Login Information of DVR_________________ 52
8-1.3 Live Monitoring Operation _______________________________ 52
8-1.3.1 Scroll the Image ___________________________________ 53
8-1.3.2 Image Quality Setup _______________________________ 53
8-1.3.3 Channel Display ___________________________________ 53
8-1.3.4 Size of Image _____________________________________ 54
8-1.3.5 Rotate the image __________________________________ 54
8-1.3.6 Alarm ____________________________________________ 54
8-2 Mobile Application Installation and Operation for Windows Mobile Sy
stem __________________________________________________________ 55
8-2.1 Mobile Application Installation____________________________ 55
8-2.2 Mobile Application Operation_____________________________ 56
8-2.3 Operation under the LIVE monitoring. _____________________ 57
CHAPTER 9 CMS INSTALLATION AND USAGE GUIDE___________________ 58
9-1 CMS Installation _____________________________________________ 58
9-2 CMS LOGIN AND ENVIRONMENT______________________________ 61
9-3 DVRs, Groups & Events______________________________________ 62
9-3.1 View DVR Я Group List __________________________________ 62
9-3.2 View Event Logs _______________________________________ 63
9-4 Local PC Information and Control _____________________________ 63
9-5 Main Display ________________________________________________ 64
9-5.1 Audio Control __________________________________________ 64
9-5.2 eMAP Display __________________________________________ 65
9-5.3 PTZ Control____________________________________________ 66
9-6 Operation Bar_______________________________________________ 67
9-6.1 User administration _____________________________________ 68
9-6.2 DVR Administration _____________________________________ 68
9-6.3 Group Administration ___________________________________ 69
9-6.4 eMap Administration ____________________________________ 70
9-6.5 Remote Play ___________________________________________ 71
9-6.6 HDD Playback __________________________________________ 72
9-6.7 File Playback___________________________________________ 72
9-6.8 Event Playback _________________________________________ 73
9-6.9 Snapshot Data _________________________________________ 73
9-6.10 Recording Data________________________________________ 74
APPENDIX I I-DVR.NET REGISTRATION _____________________________ 75
APPENDIX II Remote Monitoring IE ActiveX Control Installation Instruction ___ 77

2010.01.22 411L User Manual V0.6(M02) 5
CHAPTER 1 PACKING DETAIL AND INSTALLATION
1-1 PACKING
1. DVR
Note: Standard shipping products do not include HDD
3. IR Remote Control
7. Screws x4
4. Batteries x2
2. Quick Start
6. SATA Cord x1
8. Power Adaptor
5. CD

2010.01.22 411L User Manual V0.6(M02) 6
1-2 Hard Disk Installation
Step 1: Take off the three screws from the bottom of the DVR as indicated in red circles in
the picture below.
Step 2: Open the cover follow the way the arrows indicate.
ʳʳʳStep 3: Fix the HDD to rack mount and connect SATA and the power cable as indi
cated.

2010.01.22 411L User Manual V0.6(M02) 7
Step 4: Put DVR bottom up, screw to fix the HDD as indicated.ʳʳʳʳʳStep 5: Put the cover back and put the three screws back to fix the cover in the bottom of
the DVR.
ʳ

2010.01.22 411L User Manual V0.6(M02) 8
ʳ
ʳ
ʳ
NOTE: The initialization of new-installed HDD is required before recording, please refer to
manual “4-8UTILITY SETUP” for detail.

2010.01.22 411L User Manual V0.6(M02) 9
ʳ
CHAPTER 2 PANEL LOCATIONʳ
ʳ
2-1 FRONT PANEL CONTROLS
ʳʳ1USB Port Top(USB2.0) is used to plug the USB memory stick
Bottom(USB1.1) is used to plug the mouse
2LED DisplayˀPower DVR Power is on.
3LED DisplayʳˀHDD Hard disk is in use.
4LED DisplayʳˀLAN Connected to the internet.
5LED DisplayˀLOGIN Remote user logged in.
6LED DisplayʳˀREC DVR Recording. (or Schedule Recording and recording are
on)
7LED DisplayʳˀPLAY DVR Playing back.
8IR Sensor Input sensor for the remote control.
ĺļ
Ľ
ľ
ķĸĹĻ

2010.01.22 411L User Manual V0.6(M02) 10
2-2 4CH REAR PANEL CONNECTORS
ķĹĺľʳʳʳʳʳĸĻļĽĿķDC 12V Socket for a DC 12V input.
ĸMAIN monitor BNC port for the main monitor.
ĹVIDEO IN BNC input ports for cameras, 16 in total.ʳĺAUDIO IN RCA input port for audio signal.
ĻAUDIO OUT RCA output for audio signal.
ļNTSCЯPAL Switch Switch between NTSC and PAL format.
ĽLAN Network port.
ľGVGA VGA port.
ĿEXTERNAL I/O EXTERNAL I/O port (see below for pin definition)

2010.01.22 411L User Manual V0.6(M02) 11
CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS
The IR remote control and mouse operate differently under each mode; this chapter describes
the functions of them under three different modes: LIVE, PLAYBACK and PTZ.
3-1 LIVE Mode
You can monitor all the channels, listen to audio signal and have some related operations under
LIVE mode. This paragraph describes the IR remote control, mouse operation and on screen
graphical icons under LIVE mode.
Table 3-1.1 Functions of remote control under LIVE mode
Button Description
REC Start/Stop recording.
PLAY Start playing back the most recently recorded segment.
LOCK Enable/Disable the Keypad function
1,2,3,4 Select the channel to monitor in full screen
FREEZE Turn on/off screen freeze function.
Switch to quad display.
ENTER/MODE Switch to full screen, quad display.
MENU/ Enable/ Disable setup Menu.
BK-UP/ESC Enable/ Disable backup menu.
SRH Enable/ Disable search menu.
MUTE Switch channel 1 output audio / turn off LIVE audio
STATUS Enable/ Disable Status.
OSD Turn on/off the screen display
Zoom/Zoom - Enable/ Disable double screen size display. You can click on the channel
name for choosing a specific channel.
PIP/Zoom + Turn on picture-in-picture format. Click on the channel name can switch to
other channels.
PTZ Enable PTZ control.
AUTO In AUTO mode, all available channels will be cycled through in full screen.

2010.01.22 411L User Manual V0.6(M02) 12
Table 3-1.2 Graphical icons that will display after right-clicking your mouse under LIVE mode.
Icon Description
Resting the cursor on this icon will bring up the following four menu icons.
Main menu.
Search menu.
Backup menu.
PTZ mode.
Turn on/off recording.
Playback.
Resting the cursor on this icon will bring up the following five display icons.
FREEZE.
PIP, picture in picture
ZOOM, double the screen size
AUTO-sequence
LOCK, activate the key lock.
Full screen display.
Quad display.

2010.01.22 411L User Manual V0.6(M02) 13
Table 3-1.3 Description of on screen graphical icons in LIVE mode
Icon Description
Recording is on
1~4 Live Audio is on
Live Audio is off
Motion detected on the channel
Sensor triggered on the channel
Video loss detected on the channel
USB device detected
DVD burner is detected
Connected to the LAN cable.
FilmΚNormal Recording
ClockΚSchedule Recording
AUTO-seq is on
2X 2X zoom in is on
Freeze is on, screen is frozen
LOCK is on
PTZ control is on
Shows the current hard disk space has been used
(99% mean used 99%, remain 1%)
Lower right of each CH will show the current time
Icon Description
/ Image quality (High/Low)
/ Full screen
Record
Snap shot (Photo time in accordance with computer-based)
Record and snap shot file saving path setup
Enable/Disable shortcut toolbar

2010.01.22 411L User Manual V0.6(M02) 14
3-2 PLAYBACK Mode
Switch to PLAYBACK mode by pressing “PLAY” under the LIVE mode, the graphical icon
will show up on the upper center of the screen and the operation panel ( see below picture) will
show up at right lower corner of the screen. You can drag the panel by mouse to place it on
any location of your screen.
Table 3-2.1 Remote control functions under the PLAYBACK mode
Button Description
ENTER / MODE Switch to full screen, quad.
MENU / Turn on/off PAUSE.
PLAY Play back at normal speed.
/ SLOW Play back at slower speed. The speed will be slowed to 1/2, 1/4, 1/8,
1/16 by each pressing of the button till the slowest limitation of 1/16 of
the normal speed. Current playback speed is shown in the upper
center of the screen.
/ Fast rewind. Each press increases the speed to the next level. There
are six speeds: 2x, 4X, 8X, 16x, 32X and 64X.
/ Fast forward. Each press increases the speed to the next level. There
are six speeds: 2x, 4X, 8X, 16x, 32X and 64X.
/ Stop playback.

2010.01.22 411L User Manual V0.6(M02) 15
Table 3-2.2 The mouse operation under the PLAYBACK mode.
Icon Description
ψ/ ωFast rewind
ψ/ ωFast forward
ЯPlay/pause
ψϧ/ SLOWωΔslow playback
ψϰ/ Ϯωstop playback
Playback channel by channel with snap shot display
Full screen display
Quad display
Zoom-in display

2010.01.22 411L User Manual V0.6(M02) 16
3-3 PTZ Mode
Switch to the PTZ mode by pressing “PTZ” button under the LIVE mode. The PTZ icon
will appear on upper left side of screen and the control panel will appear on the down right side
of screen.
Table 3-3.1 Remote Control functions under the PTZ mode
Button Description
/ SLOW Move PTZ up.
/ Move PTZ down.
/ Move PTZ to the left.
/ Move PTZ to the right.
ZOOM + PTZ zoom-in.
ZOOM - PTZ zoom-out.
FOCUS + PTZ focus-in.
FOCUS - PTZ focus-out.
IRIS + PTZ iris-open.
IRIS - PTZ iris-close.
TOUR Activate PTZ pre-set tour. ϠPRESET+
Number
Setup the Preset location
Press “PRESET” key first then two-digit number; DVR will set the current
PTZ location at entered preset number.
PLAY+
Number
Go to Preset location
Press “PLAY” key first then two-digit number, PTZ will go to the
correspondent preset number location.
PIP Set current PTZ location as the start of line-scan. ϠFREEZE Activate auto line-scan. ϠZOOM Set current PTZ location as the end of line-scan.ϠϠʳPTZ communication protocols from different brands aren’t compatible 100% sometime
s. Therefore, some of these functions may be unavailable.

2010.01.22 411L User Manual V0.6(M02) 17
Table 3-3.2 Mouse operation under the PTZ mode
Icon Description
Leave PTZ ModeΔback to the LIVE mode
Pre-set number N. (0~255)
Go to pre-set number N.
Set current PTZ location at pre-set number N.
ψTOURωΔpress to activate pre-set tourϠψPIPωΔSet current PTZ location as the start of line-scan. ϠψFREEZEωΔActivate line-scan. ϠψZOOMωΔSet current PTZ location as the end of line-scan. ϠTo move PTZ in 360PTZ zoom in; PTZ zoom out
PTZ focus in; PTZ focus out.
PTZ IRIS open, PTZ IRIS close.
Below functions need support from specific PTZ manufacturer. Please check us
er manual of your PTZ for more detail.
to AUX 1~8,ψAUTOωKey ЀNumber keyψ1~8ωψBackupω, Customized functionΖϠPTZ communication protocols from different brands aren’t compatible 100%
sometimes. Therefore, some of these functions may be unavailable.

2010.01.22 411L User Manual V0.6(M02) 18
CHAPTER 4 MAIN MENU SETUP
To enter the main menu and set up DVR, log-in account and user password are required.
The default password of the administrator is “123456”. Please check the “Account Setup” for
related setup of other log-in users.
Table 4-0.1 Some definition of virtual keyboard.
Item Description
Switch between capital and small letters.
/ Switch between numbers and letters.
Press to cancel the setup, and re-choose the login
account.
Delete the last character.
Enter to identify the password. It will enter the set
up menu, If the password is verified.
Space key

2010.01.22 411L User Manual V0.6(M02) 19
Table 4-0.2 The operation of remote control under the setting menu
Item Description
Switch to different options under one item
Switch to different items
MENU Save setup and back to LIVE mode
ESC Back to Upper level of menu without saving
ENTER Enter the menu, or display virtual keyboard
PS. The initialization of new-installed HD is required before recording, please refer to “4-9
UTILITY SETUP” for detail.
4-1 RECORD SETUP
Item Description
HDD FULL
Select STOP to stop recording or OVERWRITE to reuse the
HDD when HDD is full
ψStopωΚStop Recording
ψOverwriteωΚStart to overwrite that begin from the oldest data
of HDD, and continue to record.
Quality & Frame Rate
Setup
Setup the quality and frame rate for each channel under normal
recording and event recording type.
OSD position X Setup OSD X axis
OSD position Y Set up OSD y axis
Recording OSD
position setup
Set up OSD axis

2010.01.22 411L User Manual V0.6(M02) 20
4-1.1 Quality & Frame Rate Setup
Item Description
Normal setup/
event setup Select recording mode
Resolution Select recording resolution: NTSC:360x240, 720x240, 720x480
PAL:352X288,704X288,704X576
Record Type You can setup quality and FPS separately for record type.
No. Check/uncheck the box enable/disable selected channel recording
Quality Select quality: Below Basic/ Basic/ Normal/ High/ Highest
FPS Select recording frame rate.
Auto Assign each channel with its maxima accessible fps
4-2 EVENT SETUP