RBH Sound Ultra Series User manual

Ultra Series
Soundbar/ On-wall LCR Speakers
OWNER’S MANUAL

Introduction
Congratulations on your purchase of RBH Ultra Series speaker! Your speaker is the result of
many years of research and development dedicated to producing high quality products for
home audio systems.
This manual contains features, setup recommendations and specifications for the RBH
Ultra Series speakers. We recommend you thoroughly read through the material contained
in this manual before connecting your soundbar speaker. This will ensure you have a good
understanding of how to setup your speakers for optimum performance and allow for years
of listening enjoyment.
Break-in Period
Allow 10-15 hours of listening time to adequately break-in the RBH Ultra Series speakers.
As the speaker’s break-in, the driver suspension will loosen. The result of break-in will be an
increase in low frequency response, improved definition, and increased clarity and detail.
Care and Cleaning
The unique grille for the Ultra Series has been designed to be as lightweight and acoustically
transparent as possible and is held in place by magnets imbedded in the frame of the cabinet.
If the grille requires cleaning carefully lift the grille off the speaker and lightly vacuum
any dust if necessary. The speakers cabinet has a durable finish that should only require dry
dusting or cleaning with a dry cloth. Avoid the use of abrasive or solvent-based cleaners
and harsh detergents.
Ultra Series Soundbar On-wall / LCR Speakers
1
Innovative and proprietary inverted domed aluminum 4-inch woofers and aluminum tweeters
with textured phase plugs make it all possible on the RBH Ultra Series Ultra-3 on-wall
soundbar/LCR and the Ultra-1 on-wall surround speakers.
Ultra-1 On-wall/Surround Speakers
Ultra-3 On-wall Soundbar/LCR Speaker: It’s fast to mount. And…it’s custom
sized to fit most on-wall TVs! It can be custom cut to match TV widths of
47 to 63 inches which fit most popular sizes.

2
Attaching Speaker Wires
The Ultra Series speakers use spring-loaded speaker wire
terminals to firmly hold either a pin connector or bare speaker
wire. To obtain a better connection, it is important to slightly
tug on the wires after they have been secured in the terminals.
Since the Ultra-3 soundbar speaker contains the LEFT, RIGHT
and CENTER channels, connect each one of these channels
from your amplifier. Using 16-gauge or larger speaker wire,
connect the RED “positive” (+) terminal of the LEFT speaker
to the RED “positive” (+) terminal of your amplifier’s LEFT
channel. Connect the BLACK “negative” (-) terminal of the left
speaker to the BLACK “negative” (-) terminal of your amplifier’s
left channel. Repeat for the right and the center channels.
WARNING: Make sure that no bare wires from any of the
connections touch each other or any other terminals as this
could cause a short and damage your equipment.
1. Remove the last 4 inches of the speaker wire jacket at end
of each cable to allow easier pull-through and connection
flexibility of the + and – individual wires.
2. Use a wire stripper to remove about 3/8-inch of insulation
from the end of each + and – wires.
3. Twist the ends of each conductor to secure loose strands.
4. Connect the positive (+) wire to the red terminal on the
front of the speaker by pressing down on the red positive
(+) terminal’s tab, inserting the end of the positive
conductor, and releasing the tab.
5. Repeat this procedure to connect the negative (-)
conductor to the black negative (-) terminal.
Features
Fast to mount. The Ultra-3 can be custom sized to widths of 47 to 63 to fit most popular sized
on-wall TVs. Both the Ultra-1 and Ultra-3 have a contemporary design, magnetic mounted
black fabric grille, and are only 1-5/8-inches deep. The speaker enclosure features internal
bracing and sealed separate internal chambers for each channel to produce the great sound
you need and expect from RBH. Innovative and proprietary inverted-dome aluminum 4-inch
woofers and 1-inch aluminum tweeters with textured phase plugs make the thin cabinet yet
big sound possible. Our ez-wire terminals and fast mounting, including direct-from-front
screw-through mount holes (hidden until needed), make the Ultra Series speakers easier to
install. The Ultra Series speakers provide effortless, quick, brilliant sound.

#10 screw (x2) and anchor (x4)
for keyhole mounting. Anchor is
also used for through-cabinet
mounting with #8 coarse thread
bugle head black drywall screw
#8 x 2½-inch bugle head black
coarse drywall screw (x4) for
through cabinet direct to
wall mounting.
Keyhole Bracket
Terminal Port
Pilot Hole Location
Pilot Hole Location
Pilot Hole Location
Pilot Hole Location
3
On-wall Installation
To mount your Ultra Series speakers on a wall, determine a suitable location and complete
all wiring to the speaker location before mounting the speaker to the wall. Be sure to check
for wiring and drywall screws behind planned pilot hole locations. Do not ceiling-mount.
There are two mounting methods.
1. To Mount using the imbedded keyhole mounting brackets.
a. Use the included template and choose mount position for the speaker (horizontal
or vertical). Tape the template to wall, making sure it is level (when horizontally
mounting) or plumb (when vertically mounting) and positioned correctly, centered
with the TV. Mark on wall the pilot-hole locations through the template and remove
template. Leave a minimum of one inch space between speaker cabinet edge and
TV edge. Keep in mind that, when mounted, the speaker will “lock” into position
5/16-inch lower than where the pilot holes are drilled.
b. Pre-drill 1/8-inch pilot holes in marked locations. If drilling into a wall stud (ideal)
it is recommended to use #10 mounting screws (included). If there is no stud where
a pilot hole is located drill 1/4-inch pilot hole through drywall, install wall anchors
(included) into the pilot holes.
c. Feed speaker wires through the terminal port from back of speaker. Gently center
the rear “+” keyhole bracket on to the screw heads then push back slightly and then
down to lock into position.
d. Attach each wire to appropriate spring-terminal binding post.
e. Test speaker function and attach magnetically held grille.
Back diagram for the Ultra-3 soundbar showing the keyhole brackets, pilot holes and terminal port.

Screw-through Location
Screw-through Location
Screw-through Location
Screw-through Location
Terminal Port
#10 screw (x2) and anchor (x4)
for keyhole mounting. Anchor is
also used for through-cabinet
mounting with #8 coarse thread
bugle head black drywall screw
#8 x 2½-inch bugle head black
coarse drywall screw (x4) for
through cabinet direct to
wall mounting.
Keyhole Bracket
Pilot Hole Location
Pilot Hole Location
Pilot Hole Location
Pilot Hole Location
Terminal Port
4
On-wall Installation (continued)
2. To use the “screw-through ez-mount” method, (allows for tighter fit to edge of TV).
a. Using finger or eraser-end of a pencil locate the covered screw-through locations
and depress slightly so they can be easily located, (see drawing below).
b. Insert 2½-inch black drywall or cabinet screws (included) into the center of depressed
locations.
c. Align speaker as desired. Use a level to be sure or align with edge of TV. Then slightly
start each screw to mark locations on wall then reverse screws to allow removal of
speaker but leave screws in the cabinet’s pilot holes.
d. Drill ¼-inch hole through the screw-marked locations; insert drywall anchors
(included). If location happens to be a wood stud no pilot hold is needed since wall
anchor will not be used.
e. Feed speaker wires through the terminal port from back of speaker and pull through
front of terminal port then re-mount the speaker by securing the screws into the
drywall anchors or stud(s).
f. Attach each wire to appropriate spring-terminal binding post.
g. Test speaker function and attach magnetically held grille.
Back diagram for the Ultra-1 on-wall speaker showing the keyhole braclets, pilot holes and terminal port.

SOUNDBAR
In order to obtain the best possible sound from your speaker system, it is important to
determine where the Ultra Series speakers will sound best in your listening room. Room
reflections from the floor, ceiling and side walls influence the balance, imaging and overall
sonic quality at the listening position. Experiment with speaker placement to determine
which location offers the best overall sound. Of course, this will be dictated by the TV
placement for sound-bar use. As a general guide, use the room layout diagram and the
following descriptions when setting up a home theater system. Some speakers shown in
the diagram below may not be applicable to your individual system.
The Ultra-3 soundbar speaker is designed to be used as a LCR (Left–Center–Right) speaker
with flat-panel TVs such as plasma and LCD monitors. This will usually dictate placing the
speakers below or above the TV.
The Ultra-1 on-wall surround speaker is designed to be used as surround speakers which will
usually dictate mounting the speakers vertically or horizontally on either side of the TV.
The Ultra Series speaker sounds best when mounted to a wall. Another mounting option
for the Ultra-3 is mounting to TV using our SB-39 universal brackets to accommodate
articulating TV mounting brackets.
Surround Speakers
The Surround Speakers may be placed either above, behind or to the sides of the listening
position. The listening position should be centered between the surround speakers. For
best performance.
Subwoofer
Placement of the subwoofer
will largely determine qual-
ity, quantity, and extension
of the bass frequencies
within your listening
room. Bass frequencies are
reinforced by close room
boundaries. Placing the
subwoofer in a corner will
make the subwoofer sound
louder and boost the very
lowest frequencies. Placing
the subwoofer away from
walls will provide the least
reinforcement, making the
bass sound subjectively
thinner than if the woofer were close to a wall. Good results can usually be obtained
by placing a subwoofer along a wall 1-3 feet from a corner. Experiment with subwoofer
placement and the sub-amplifier controls to achieve the proper bass balance.
Room Setup Suggestions
5

6
Specications
Model
Speaker Type:
Frequency Response:
Sensitivity
Recommended Power:
Woofer:
Tweeter:
Crossover Frequency:
Crossover Slope:
Impedance:
Finish/Color:
Grille Color:
Dimensions:
Adjustable from
Weight:
Ultra-3
On-wall/LCR Soundbar Speaker
100Hz-20kHz ±3dB
84db (2.38V @ 1M)
20-120 Watts
(6) 4” (102mm) Proprietary Inverted
Aluminum Cone Woofers
(3) 1” (25mm) Aluminum Diaphragm
Neodymium Magnet Tweeter with
Textured Phase Plug
3,000 Hz
12dB/Octave
8 Ohms x3
MDF/Matte Texture Black with
High-gloss End Accent Caps
Black Fabric
63” to 47” (1600mm to 1194 mm) W
6-11/16” (170mm) H
1-5/8” (41mm) D
12.5 lbs. (5.74 kg) 63” Wide
9.5 lbs. (4.30 kg) 47” Wide
Ultra-1
On-wall/Surround Speaker
100Hz-20kHz ±3dB
84db (2.38V @ 1M)
20-120 Watts
(2) 4” (102mm) Proprietary Inverted
Aluminum Cone Woofers
(1) 1” (25mm) Aluminum Diaphragm
Neodymium Magnet Tweeter with
Textured Phase Plug
3,000 Hz
12dB/Octave
8 Ohms
MDF/Matte Texture Black with
High-gloss End Accent Caps
Black Fabric
6-11/16” (170mm) W
18” (457mm) H
1-5/8” (41mm) D
3.85 lbs. (1.75 kg)

7
Warranty
Your RBH Sound Ultra-3 soundbar speaker is covered by a limited warranty against defects
in materials and workmanship for a period of 5 years from the original date of purchase.*
This warranty is provided by the authorized RBH Sound dealer where the speaker was
purchased. Warranty repair will be performed only when your purchase receipt is presented
as proof of ownership and date of purchase. Defective parts will be repaired or replaced
without charge by your dealer’s store or the location designated by RBH Sound authorized
to service RBH Sound products. Charges for unauthorized service and transportation cost
are not reimbursable under this warranty. This warranty becomes void if the product has
been damaged by alteration, misuse or neglect. RBH Sound assumes no liability for property
damage or any other incidental or consequential damage whatsoever which may result from
the failure of this product. Any and all warranties of merchantability and fitness implied
by law are limited to the duration of this express warranty. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitations may not apply
to you. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
* The Ultra-3 speaker is not intended for outdoor use. If used outdoors it is at owner’s discretion and
this warranty is void.
No sound from speakers.
No sound from
one speaker.
Very little bass
and/or imaging.
Speaker wire not connected.
Speaker selector on amplifier
is not on.
Balance control on receiver
or pre-amp is not centered.
Speaker wire not securely
connected.
Speakers are wired out
of phase.
Make sure wire is connected
at both the speaker and the
amplifier observing proper
polarity.
Activate proper selector on
amplifier.
Place balance control in the
center.
Check all connections at
amplifier and speakers.
Check entire system for proper
polarity and make adjustments
as necessary.
Troubleshooting
Probable Cause: Solution:
Situation:

8
THIS PAGE WAS LEFT BLANK INTENTIONALLY

382 Marshall Way, Layton, Utah • USA • 84041
Toll Free: [phone] • Fax: [phone]
rbhsound.com
It is RBH Sound policy to continuously incorporate improvements into our products; all specifications
are subject to change without notice. Copyright ©2014 RBH Sound. All Rights Reserved. 12032014
Redening the Way You Experience Sound.TM