RC Factory WISTED HOBBYS Bucker Jungmann User manual

3
1)

1.
2.
3.
5.
7.
9.
4.
6.
8.
10.
10.
Thin CA
Completed wings with spars installed shown above
Medium CA
Trim tabs to separate
Medium CA
Thin CA
Thin CA
L+R
L+R
L+R L+R
L+R
4 pc’s .8mm x 500mm(Aileron wing supports)

11.
13.
15.
17.
19.
12.
14.
16.
18.
20.
Completed Aileron Bracing show on both wings above
2 pcs .8mm x 500mm
(horizontal fuse runners)
.5mm x 3mm x85mm
.5mm x3mm x 100mm
Thin CA
cut
Medium CA Medium CA
Thin CA
1 pc 3mm x 330mm Tube. Check fitment make sure there is no
binding in guides, if so sand to fitment. Also make sure control
horn is slide into place as shown. Do not glue horn into place yet.
L+R
L+RL+R
For this step grab the 1 pc of .5mm x 3mm x 330 cut to 85mm & 100mm
The rest of the cut will be 115mm in lenght and used for Step #31)

21.
23.
25.
27.
29.
22.
24.
26.
28.
30.
Medium CA
No Glue
Medium CA
2 pc’s .8mm x 500mm fuse lateral truss bracing
(cut to length accordingly for both sides)
145mm 130mm 120mm 105mm Thin CA
Thin CA
Thin CA
1 pc 1mm x 330mm
(cut into two 160mm pieces)
2pcs D6M servos
Thin CA
L+R
L+R
L+RL+R
L+R
L+R
L+R

31.
33.
35.
37.
39.
32.
34.
36.
38.
40.
Medium CA
Activator
Medium CA
Thin CA
1 pc .5mm x 3mm x 115mm
(left over cut from step step #12)
(Vertical top fuse brace)
Medium CA
Medium CA
Thin CA
2 pcs .5mm x 3mm x 200mm
(wing strut braces)
L+R L+R
L+R

Medium CA
Activator
1mm x 240mm
1mm x 260mm
1mm x 250mm 1mm x 250mm
Thin CA
Thin CA
2 pcs 1.5mm x 2.5mm x 225mm (landing gear legs)
Thin CA
Medium CA
No Glue
2 pcs 1.5mm x 275mm
Landing gear braces
Thin CA
4 pcs 1mm x 500mm
bracing. Cut to size
50
49
41 42
43 44
45 46
47 48

Thin CA
Thin CA Medium CA
Thin CA
cut to 12mm
Medium CA
Medium CA
51 52
53 54
55 56
57 58
1.5mm x 30mm Alxe rods
59 60

61.
63.
65.
67.
69.
62.
64.
66.
68.
70.
Medium CA
Medium CA
Activator
12mm
Thin CA
1 pc 1.5mm x 40mm Control rod assemble
(cut in half for 20mm) Thin CA
40mm

71.
73.
75.
77.
79.
72.
74.
76.
78.
80.
Thin CA
1mm
Clip it with the pin
Clip it with the pin
1 pc .8mm x 500
(Elevator push rod)
Thin CA
Thin CA
Thin CA
1mm

81.
83.
85.
87.
89.
82.
84.
86.
88.
90.
Clip it with the pin
Clip it with the pin
Thin CA
Thin CA
Trim To length
1 pc .8mm x 500
(elevator push rod)
cut
Clip it! 2 pcs 1.2mm x 200
(cut to size, around 190mm)
2pcs of heat shrink
Thin CA

91.
80-90mm
We wish you many happy flying hours with the Buecker
Your RC Factory team