RCA RNSM4003-B User manual

Manufactured under license from Dolby Laboratories.
Dolby,Dolby Audio,Pro logic, and the double-D symbol are
trademarks of Dolby Laboratories.
INSTRUCTION MANUALBefore using the TV, please read this manual thoroughly, and retain it for future reference.RNSM4003-B

TABLE OF CONTENTSTV Feet Installation Instructions
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONSInstall and Connect TVPreparations Guide
HOME PAGE
HOME PAGETVUSBInstructions
Main MenuPictureSoundSettingLockProgramNetworkAboutUSB
Limited Product Warranty
USB FORMAT MODE
4-899101212131414151516161617181920212223

BA4.5*18

3CautionThe lightening flash with arrowhead symbol, within an equilateral triangle isintended to alert the user to the presence of un-insulated "dangerous voltage"within the products enclosure that may be of sufficient magnitude to constitute arisk of electric shock to the persons.The exclamation point within an equilateral triangle is intend to alert the user tothe presence of important operating and maintenance (servicing) instructions inthe literature accompanying the appliance.Correct disposal of this ProductWaste Electrical & Electronic Equipment (WEEE)Your product is designed and manufactured with high quality materials andcomponents which can be recycled and reused.This symbol means that electrical and electronic equipment, at their end-of-life,should be disposed of separately from your household waste.Please dispose of this equipment at your local community wastecollection/recycling centre.In the European Union there are separate collection systems for used electricaland electronic products. Please help us to conserve the environment we live in!This is class Ⅱ apparatus whis double insulation, and no protective earth provided.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1) this device might not cause harmful interference, and(2) this device must accept any interference received, including interference that might cause undesired operation

Instructions
a tip-over and/or injury.
4

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE
ANTENNALEADIN WIREANTENNADISCHAGRE UNIT(NEC SECTION 810-20) GROUNDING CONDUCTORS(NEC SECTION 810-21)GROUND CLAMPSPOWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250,RARTH)GROUNDCLAMP
ELEC TRIC SERVICEEQUIPMENT
NEC-NATIONAL ELECTRICAL CODES2898A
26) designed in such a way that it does not require a safety connection to electrical earth.27) Correct disposal of this product. This marking indicates that this product should not be disposed with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. This equipment is a Class II or double insulated electrical appliance. It has been
Instructions
5

Warning: batteries(pack or batteries installed) should not be exposed to excessive heat such as sunshine, fire or other heat sources.
Instructions
6

Instructions
have bright spots/pixels.7

10cm10cmbelow
Instructions
Note: Drawing is a representative example only
operate
To avoid damage to the TV, place the TV on a table, face down on a soft surface.the8

TV Buttons and Connections9AV inputExternal AV Signal Input and Right/Left Audio Inputs.VIDEORLINPUTOPTICALDigital Audio Output.OPTICALUSB InputConnect to your USB device.ANT 75/RF Connection Connect to the antenna/cable TVoutput of your device or wall plate.HDMI Input(HDMI1,HDMI2,HDMI3/ARC)Connect to a HDMI outputconnection on your external device.
HDMI
HEADPHONE JACKPlug earphones into jack for private listening. Overrides speakers.HEADPHONE RJ45 Connect to the Internet.RJ 45RJ45 connectionRJ 45

1. :Turn on the TV or enter standby mode.2. :Turn on/off the sound by pressing this button.3.0~9: Figures “0-9” are used to directly input channel number.4.EPG:Press to display Electronic Program Guide and select your favorite channel. 5.-/--:Press to change the channel which name contains “.”.6. : Input source selection button.7. :Press to enter the Home Page.8.V+: Increase the volume.9.V-:Decrease the volume.10.P :Channel up.11.P :.Channel down12. :Start system menu.13. :Press to display the source and channel's display.14.OK:To confirm the choice of a highlighted menu item. 15. / :Press these buttons to move within the menu.16. / :Press these buttons to move .within the menu17.BACK:Go back to the previous step.18.EXIT:Press to exit the OSD menu.19. :Press to launch Netflix.20. :Press to launch YouTube.21. :Press to launch NetRange app store.22. :Press to launch VUDU.23.GREEN/RED/YELLOW/CYAN buttons: Press these buttons according the different prompts.24. :Press to fast reverse in USB mode.25. :Press to fast forward in USB mode.26. :Press to play the video and press again to pause the video. 27.CC:Press to display the close caption.28. :Hold on or off for current page display/Press to stop in the USB mode.29.AUDIO:Press to change the language when paly the stream which contains multi-language.10

11Remote Code: 007F. Format: NEC

The bottom view of the TV (Front cabinet faces down)TV ANTFM ANT
TV signal output
132Install and Connect TVSetup your TV1.Put your TV in a place that can support the weight of the TV. To avoid danger, please do not assemble the TV near water or extreme heat(such as a furnace, light source,or candle.) Do not block the ventilation on the back of the TV.Connect signal source and power2. Connect the antenna cable to the RF connection on the back or side of the TV, and/or the signal source HDMI cable to the HDMI input(s) on the rear or side of TV. Plug the TV into the wall power outlet (AC120 ~ 60Hz).Note:Picture for reference purposes only.TV Feet Installation Instructions121.Open the carton and remove the TV,accessories,and the feet.2.To avoid damage to the TV,place on a table,face down on a soft surface. The feet are attached to the TV with provided screws,or are attached by snapping into the cabinet till you hear the click.3.Ensure the feet are tightened/snapped-in securely. Do not overtighten.Please take note of the base direction:Turn on the TV3.Connect the power supply, enter the standby mode (red light), press the power button of the TV or the power button on the remote control to turn on the TV(No light).

OPERATING INSTRUCTIONS
13 Pressbutton to select the language.【▼】 /【▲】Pressbutton to continue.【OK】The User Interface defaults to the “Skip” option.Press the【OK】button to skip the DTV channel tuning then enter the ATV channel tuning.Pressbutton to select the i.【▼】 /【▲】nput sourcePressbutton to continue.【OK】

HOME PAGEMain Menu
14Press button to enter homepage.Press 【▼】 /【▲】 button to select Apps,NETFLIX,Input source,andSettings options,Press 【◄】/【►】 button to select the correspondingsub-option and press the [OK] button to confirm.Press button to enter main menu.Press 【▼】 /【▲】 button to select Picture / Sound / Setting / Lock / PVR Option / Program / Network / About menus. Press 【►】 button to continue to sub menu.

PictureSound
151.Press button to enter main menu . Press【►】 button to select Picture menu. 2.Press 【▼】 /【▲】 button to select Picture Mode / Contrast / Brightness / Color /Sharpness / Tint / Backlight / Color Temperature / Aspect Ratio / Noise Reduction.Tint feature only works in ATV and DTV mode when entered to Picture Mode 'User'.3.Press【◄】/【►】button to adjust or select.1.Press button to enter main menu . Press【►】 button to select Sound menu. 2.Press 【▼】 /【▲】 /button to select Sound Mode / Equalizer / Balance / Auto Volume Limit / Surround Sound / Digital output type / Audio Delay / Video Description / Audio Languages.3.Press【◄】/【►】button to adjust or select.

SettingLock
16

ProgramNetwork
17

About
18 --By USB: Enables you to install a new version software from a USB stick,if available.Insert the USB stick containing a new version of the software into Follow the on-screen instructions to complete the process. a USB socket of the set. Select USB and press OK to enter.

USB
19Insert a USB flash drive and press the [OK] button in the USB menu to enter the Media menu.Press the【◄】/【►】button Select the inserted USB flash device, then press the [OK] button to access the started media on the USB device.Press the【◄】/ 【►】 buttons to select ALL, Photo, Music, Video options. Press the button to select the file type. 【OK】 Select the “Return” icon and press to return to the USB directory to【OK】 make your selection. Select a file press thebutton to enter the video file. 【OK】