RCA RLDEDV2813-C User manual

INSTRUCTION MANUAL
LED TV
RLDEDV2813-C
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device might not cause harmful interference, and
(2) this device must accept any interference received,
including interference that might cause undesired operation

Table of Contents
1
Caution
Important Safety Precautions
Top/Side panel diagram
Remote Controller
Battery Installation
Using the Remote Control
Install TV
Set your TV
Connect Antenna and power
Turn On TV
Help
2
3
4
6-7
8
9
12-13
15-31
36
37
TV Bracket assembly 5
Specifications
Setup Wizard
Wall Mount Installation
Main Menu Operation
Sound Menu
Time Menu
Setup Menu
Close Caption
Lock Menu
US Rating
TV
MPAA
Canada Rating
Hotel Menu
Channel Menu
15-17
17-18
19
20
21-23
Systems Connection 10
14
Select Input Source
TV
24-25
26
26
27
27
28-29
30-31
PC 32-33
PC Menu
DVD Setup 34-35

The lightening flash with arrowhead symbol, within an equilateral triangle is
intended to alert the user to the presence of un-insulated "dangerous voltage"
within the products enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to the persons.
The exclamation point within an equilateral triangle is intend to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
Correct disposal of this Product
W aste Electrical & Electronic Equipment (WEEE)
Your product is designed and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their end-of-life,
should be disposed of separately from your household waste.
Please dispose of this equipment at your local community waste
collection/recycling centre.
In the European Union there are separate collection systems for used electrical
and electronic products. Please help us to conserve the environment we live in!
Caution
2

3

4
8
10cm
4
3.95” x 3.95”
100 100
Wall Mount Installation
20cm

TV Bracket assembly
5
s

Indicator on(Red) Standby mode
Indicator on(Green) Power on mode
(IR) Infrared Receiver: Receives IR signals from the remote control.
(Power on/Standby) LED Indicator: Press to turn on and off
VOL
The functions of the buttons on the are as follows:TV
CH+/-:When watching TV: select channels.
(DVD Mode. CH-:DVD Eject. CH+:Play/Pause DVD Program)
MENU:
1.Press Menu.
2.Press SOURCE to enter.
3.Use CH+/- to shift UP/DOWN.
4.Press SOURCE to confirm,then press VOL+/-to adjust.
5.Press SOURCE to confirm
Top panel diagram
6
SOURCE External signal input selection and confirm the
item selected.
/
/

Side Panel Diagram
7
(Left Side)
(Back Side)
Connect to ANT or cable source
PC AUDIO IN PC audio input
VGA IN VGA signal from computer output
YPbPr Connect to the composite terminal of your DVD/VCR
ANT 75 Ω
EARPHONE
For Upgrade Use
AV INPUT
Earphone output
COAXIAL Digital Audio Output
Service Port
HDMI IN Connect to HDMI of DVD or other equipment
Name Function Description
AUDIO OUTPUT Right/Left Audio Output
AC 120V~
60Hz
OUT PUT
VIDEO/Y
Pb Pr
COAXIA L
EARPHONE
service port
ANT 75

Remote Controller
8
Univer sal rem ote cod e
This is the code for rem ote cont rol of
RLD EDV2813-C,i f you want to change to a
uni vers al rem ot e cont rol ,you can edi t
thi s code int o your uni vers al remote cont rol.
(1)Open the battery compartment cover
on the back side
(2)Insert two 1.5V batteries of AAA type
with correct polarity
(3)Close the battery compartment cover
on the back side
Universal Remote Control code:007F
(Universal Remote control is not included)
MENU SOUR CE
ENTER
EXIT
SLEEP
P.MOD E S.MODE
DISPLAY
MTS / MP3PROG
ZOOM
D.MENU D.TITLE
ANGLE
EPG
D.DISP
REV FWD PREV
FAV-
GOTO
AUDIO SUBTITLE
FAV FAV+
PROG STEP REPEAT A-B
NEXT
D.setup
D.Menu D.Title Goto D.Disp
PROG STEP REPEAT A-B
Zoom Angle Subtitle Audio
D.TITLE:
A-B During the playback,press this button to repeat
playback of a specific section on a disc.
SLEEP: Select amount of time before TV turn
off
automatically.
S.MODE: Press to cycle through the different sound settings
P.MODE: Press to cycle through the different picture settings
D.DISP:
D.MENU:
Press "-" to enter a program number for multiple program
channel, such as 2-1 etc.
GOTO:
STEP：Play for single frame image
ZOOM In DVD source adjust DVD picture size
MTS / MP3PROG:
Press to select the audio mode,you can select stereo,Mono,
or SAP(second audio program)./When playing mp3 disc,
press MP3 PROG and add the favorite music to playlist,
press PROG two times to see the programmed playlist.
CH +/- : Press to scan through or to select a channel.
V +/-: Press to increase / decrease the sound level.
EPG:
D.Setup:
AVTV HDMI PC
YPbPr DVD

3
side
indicator
9
10cm
10cm 10cm
LED TV

2
10
Component
AC 12 0V ~
60Hz
OUTP UT
VIDEO/Y
Pb Pr
COAXIA L
EARP HONE
AC 12 0V ~
60Hz
OUTP UT
VIDEO/Y
Pb Pr
COAXIA L
EARP HONE

11
service port
ANT 75
service port
ANT 75

12
Setup Wizard
Connect an RF cable from the TV’s input called “RF-In” and to your TV Aerial socket.
Select Time
Press ▼ / ▲ button to select the time zone, daylight saving time and time format you want to.
Press </ > button on the remote control to adjust.
Press ▼ / ▲ button on the remote control to select go to next step and press ENTER/ button
to go.
Select TV Configuration
TV Configuration

13
Auto Scan
Press </ > button to select the antenna type.
Press ▼ / ▲ button to select go to next step and press ENTER/> button to start auto scan.
Setup Wizard

14
Select Input Source
Press INPUT button to display the input source list,
Press ▼ / ▲ or button to select the input
source you want to,
Press ENTER button to enter the input source,
Press EXIT button to quit.
INPUT
Main Menu
Press MENU to display the main menu or return to the previous menu or close the main menu.
Press </ > to highlight the desired menu icon, and press ENTER to select.
Source Select
TV
AV
Component
DVD
HDMI1
PC
HDMI2
HDMI3

15
TV
Picture Menu
Pre ss
Pre ss
Pre ss
Pre ss
ENU to ente r th e main menu, Press butt on to select.
Pre ss to enter.
ENU again to exit or back to pare nt menu.
butt on to select among Pictu re Mode /B ri ghtn ess/ Contra st / Color / Tint / Sharp ness / Color
Tempera tu re / Advanced Sett ings.
Pre ss to enter.
Pre ss button to adjust.
ENU again or back to pare nt menu.
M</ >
ENTER / ▼
M
▼ / ▲
ENTER / ▼
</ >
M
【Pic tu re Mode】
Adjust pictu re mode to change pictu re appeara nce.
Note :The brightn ess,c ontra st, color, ti nt and sharp ness are only available in User mode,you can adjust as
you like.
Sta ndard Pro duces a highly defi ned image in a norm ally lit room.
Dynamic Pro duces a highly defi ned image in a bri ghtl y lit ro om.
Soft Pro duces a highly defi ned image in a soft lit room.
User Select to custo mize pictu re settings.
【Brig htn ess】
Adjust th e visual percepti on outp ut of th e enti re pictu re , it will effe ct th e iuminousness of th e pictu re.
Pre ss button to adjust.</ >
【Contra st】
Adjust th e highlight inte nsity of th e pictu re, but the shadow of th e picture is invari able.
Pre ss button to adjust.</ >
Main Menu Operation
Power saving Produces a lower power consumption mode.
/ Power saving

16
TV
【Colo r】
【Tint】
Adjust th e hue(Red,Gre en,B lue) of th e pictu re.
Pre ss button to adjust.
【Sharpness】
Pre ss button to adjust.
【Colo r Temperatu re】
【Advanced Settin gs】
Adjust advanced video fe ature s to fine tune th e pictu re .
Pre ss butt on to ente r .
【Aspect Ratio 】
Adjust how th e pictu re fi lls th e scre en.
【Nois e Reductio n】
Set opti ons to re duce video noise.
Adjust th e satu rati on of th e color based on your own like.
</ >
</ >
Adjust th e peaking in th e deta il of th e pictu re.
</ >
Increase or re duce warm color of th e pictu re personally(re d),a nd th e cool color pers onally(blue) accord ing
to your like.
> sub-menu.
Pre ss butt on to adjust.
Norm al
Norm al Automatically adjust Aspect Rati o based on TV size and TV pro gra m.
Wide Use to watch wide screen(16:9) conte nt.
Zoom Expands image to fill scre en. Top and butt on maybe cut off.
Cinema Stre tc hes image at edges but keeps a clear image in th e cente r.
Off Select to tu rn off video noise detection.
Low Dete ct and reduce low video noise.
Medium Dete ct and reduce modera te video noise.
High Detect and re duce enhanced video noise.
Auto Dete ct and reduce video noise auto matically.
Increase the sex-l inked colors fo r th e white .
Warm Increase the re d color fo r th e white.
Cool Increase the blue to ne fo r th e white.

17
TV
Sound Menu
Pre ss
Pre ss
Pre ss
Pre ss
ENU to ente r th e main menu, Press butt on to select.
Pre ss to enter.
ENU again to exit or back to parent menu.
butt on to select among /S ound Mode / Bass / Treble / Balance /MTS/ Audio Language
/Digita l Audio Outp ut/ Surro und Sound/ AVL .
Pre ss to enter.
Pre ss button to adjust.
ENU again or back to pare nt menu.
M</ >
ENTER / ▼
M
▼ / ▲
ENTER / ▼
</ >
M
【HDMI Mode】
Only available in HDMI input.
【Dynamic Contra st】
Auto mati cally adjust picture deta il and brightn ess.
Pre ss button to select (O ff/O n).
Pre ss button to select (Video/Gra phic).
</ >
</ >

18
TV
【Sound Mode】
Select a sound mode to achieve ideal sound.
Pre ss button to select(S tandard / Music / Movie / Sports / User) .</ >
Note :The bass and tre ble are only available in User mode,y ou can adjust as you like.
Sta ndard Pro duces a balanced sound in all environments.
Music Preserves the ori ginal sound. Good for musical pro gra ms.
Movie Enhances tre ble and bass fo r a ri ch sound experi ence.
Sports Enhances vocals fo r TV audio.
User Select to custo mize audio sett ings.
【Bass】
Adjust th e bass effe ct. Incre ases or decre ases lower-p itc hed sounds.
Pre ss butt on to adjust.</ >
【Treble】
Adjust th e tre ble effe ct.In creases or decre ases high-p itc hed sounds.
Pre ss butt on to adjust.</ >
【Bala nce】
Adjust th e balance betw een left and ri ght speakers to adapt to your liste ning positi on.
Pre ss butt on to adjust.</ >
【MTS】
It is only available in ATV. Configures th e multi-tra ck sound.
Pre ss button to select(M ono/S tere o/SAP).</ >
Mono Sets the sound to mono.
Ste re o Sets th e sound to ste reo when stere o is not available, th e sound is auto mati cally switched
to mono.
SAP Sets th e sound to th e second audio program.
【Audio Language】
. It is only available in DTV. Select th e language supporte d by th e chosen digital channel
Pre ss button to select(E nglish / / ).</ > Fre nch Spanish
【Dig ita l Audio Outp ut】
Send digita l audio to extern al audio syste m.
Pre ss button to select.</ >
PCM Select to outp ut audio in 2-channel ste reo.
Raw Ori ginal image coded date.
Off Set digita l audio output off.
【AVL】
Set th e auto volume contro l.
Pre ss butt on to </ > select(O n / Off) .
NOTE:
Balance: This item can adjust the speaker’s output, it enables you to listen to best at your position.
AVL: This item uses for reducing the difference between channel and program’s
volume automatically.
it made the overall water to be even. This function will also reduce the fluctuation of the sound.
【Surr ound Sound】
Pre ss butt on to </ > select(O n / Off) .

19
TV
Time Menu
Pre ss
Pre ss
Pre ss
Pre ss
ENU to ente r th e main menu, Press butt on to select.
Pre ss to enter.
ENU again to exit or back to pare nt menu.
butt on to select among Sleep Timer / Time Zone / Daylight Saving Time / Time Form at / Auto
Clock / Clock.
Pre ss to enter.
Pre ss button to adjust.
ENU again or back to pare nt menu.
M</ >
ENTER / ▼
M
▼ / ▲
ENTER / ▼
</ >
M
Time Zone
Daylight Saving Tim e
Time Format
Auto Clo ck
【Sle ep Timer】
Set a ti mer fo r th e TV to turn off auto mati cally.
Pre ss button to select(O ff / 5min/1 0min /15min/ 30min / 60min / 90min / 120min/1 80min/2 40min).
【 】
Select your ti me zone.
Pre ss button to select(E astern / Centra l / Mounta in / Pacifi c / Alaska / Hawaii /Samoa/
Newfoundland / Atl anti c).
【 】
Set th e daylight saving time for your are a.
Pre ss button to select(O n / Off) .
【 】
Select your ti me fo rm at.
Pre ss button to select(1 2-h our / 24-h our) .
【 】
It is only available in DTV.
Pre ss button to select(O n / Off) .
</ >
</ >
</ >
</ >
</ >
Use to synchro nize the display automati cally.