RCS RCS-433MDR1 User manual

RCS-433MDR1
USER
MANUAL
Thank you for choosing a RCS transmitter. It is recommended
that you read this manual carefully before using the transmitter.
CONTENTS
1 - TRANSMITTER INTRODUCTION
1A - General Information
1B - Technical Specifications
1C - Main Features
1D - Model Types
2 - CODING
3 - MEMORIZATION
4 - BATTERY AND DIP-SWITCH ACCESS
5 - TROUBLESHOOTING
1 - TRANSMITTER INTRODUCTION
1A - General Information
• The radio control, RCS-433MDR1 has been designed for the
control of automatic closing systems and anti-burglar systems.
The operating frequency is 433.92 MHz.
• The transmitter security code is obtained by means of a
10 way three-state dip-switch, which allows up to 19683 codes
combinations.
• Each transmitter (or its different keys) can be stored into
different receivers and hence can do more functions.
• The product fully complies with Part 15 of FCC Regulations.
1B - Technical specifications
Number of keys: . . . . . . . . . . . . . . . . . . . . . . . . . .1
Battery duration: . . . . . . . . . . . . . . . . . .12 - 24 months
Battery type: . . . . . . . . . . . . . . . . . . . . . . . .23A (L1028)
Current consumption: . . . . . . . . . . . . . . . . . . . . .25 mA
Operating frequency: . . . . . . . . . . . . . . . . .433.92 MHz
Security code combinations number: . . . . . . . . .19683
Modulation: . . . . . . . . . . . . . . . . . . . . . . . . . . .AM/ASK
E.r.p.: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 - 100 uW
Range in open space: . . . . . . . . . . .from 100 to 200 m
Operating temperature: . . . . . . .from -10 °C to +55 °C
Dimensions: . . . . . . . . . . . . . . . . . . . . .1.75 x 1 x .3 in.
Weight: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..7 oz.

1C - Main Features
1D - Model Types
1 button dip-switch transmitter: Model #: RCS-433MDR1
2 - CODING
Using a coin, insert and twist to access to the battery and the
dip-switches. The dip-position will give the security code.
Warning:Each transmitter is set-in-factory with the same code on
the dip-switches; it highly advisable to change this code by moving
the dip-switches to any random position ( “+”, “0” , “-”).
3 - MEMORIZATION
Each dip-switch setting code has to be stored into the receiver
memory. The memorization can be done by self-learning. The
instructions for this operation is given on the receiver installation
manual. Your own installer will perform this operation during
the installation or will give you the necessary explanation
during installation.
4 - BATTERY AND DIP-SWITCH ACCESS
To access the battery, Using a coin, insert
and twist. Place the 23A alkaline
battery between the 2 contacts.
Respect the right polarity as indicated
on the bottom of the box.
NOTE:Please dispose of the battery
correctly, they are hazardous waste.
5 - TROUBLESHOOTING
The radio signal is not verifiable Replace the transmitter battery
The transmitter led doesn't switch on Replace the transmitter battery
The radio signal is not verifiable Check the power supply of
the receiver
The transmitter led switches on Replace the transmitter battery
GUARANTEE
The guarantee period of all RCS transmitters is 12 months,
beginning from the manufacturer date. During this period,
if the product does not work correctly, due to a defective
component, the product will be repaired or substituted
at the discretion of RCS. The guarantee does not cover
the plastic container integrity. After-sale service is supplied
at the producer's factory.
REMOTE CONTROL SOLUTIONS, LLC
1-866-770-0727
www.rcsremotes.com
RCS-433MDR1 FCC ID: TG6RCS433MDR
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1) This device may not cause harmful interferences; and
2) this device must accept any interference received, including interference that may cause undesired operation
Notice:Any changes or modification to RCS equipment not
expressly approved by RCS could void the user's authority to
operate the equipment.
Red LED
Button
Dip-Switch
Battery