Honeywell Xenon 1932 User manual

Xenon™ 1932/Xenon™ 1932BF
CCB04-010BT/CCB05-010BT
Cordless Area-Imaging Scanner and Charge Bases
Quick Start Guide
1932-EN-QS Rev (a)
3/18
All manuals and user guides at all-guides.com
all-guides.com

1
Note: Refer to your user’s guide for information about cleaning
your device.
Getting Started
Turn off computer’s power before connecting the scanner, then
power up the computer once the scanner is fully connected.
When the base is connected and powered up, put the scanner in
the base to establish a link. The green LED on the base flashes
to indicate the scanner’s battery or charge pack is charging.
Power Supply Assembly (if included)
Note: The power supply must be ordered separately, if needed.
All manuals and user guides at all-guides.com

CCB05-010BT Base:
CCB04-010BT Base:
2
Connecting the Scanner
USB:
All manuals and user guides at all-guides.com

CCB05-010BT Base:
CCB04-010BT Base:
3
Keyboard Wedge:
All manuals and user guides at all-guides.com

CCB05-010BT Base:
CCB04-010BT Base:
4
RS232 Serial Port:
All manuals and user guides at all-guides.com

CCB05-010BT Base:
CCB04-010BT Base:
5
RS485:
All manuals and user guides at all-guides.com
all-guides.com

6
Reading Techniques
The view finder projects an aiming beam that
should be centered over the bar code, but it
can be positioned in any direction for a good
read.
Standard Product Defaults
The following bar code resets all standard
product default settings.
RS485 Interface
The RS485 interface defaults to port 5B. If you have an IBM POS
terminal using port 9B, scan the appropriate code below to pro-
gram the terminal, then power cycle the cash register.
Note: For additional RS485 interface selections, see the User’s
Guide for your product.
Standard Product Defaults
IBM Port 9B HHBCR-1
Interface
IBM Port 9B HHBCR-2
Interface
All manuals and user guides at all-guides.com

7
USB Serial
Scan the following code to program the scanner to emulate a
regular RS232-based COM Port. Apple® Macintosh computers
recognize the scanner as a USB CDC class device and automati-
cally use a class driver.
Note: No extra configuration (e.g., baud rate) is necessary.
USB PC Keyboard
Scan the following code to program the scanner for a USB PC
Keyboard.
Keyboard Country
Scan the appropriate country code below to program the key-
board layout for your country or language. By default, national
character replacements are used for the following characters:
If you are using a Microsoft® Windows® PC, you must
download a driver from the Honeywell website. The
driver will use the next available COM Port number.
USB Serial
USB PC Keyboard
All manuals and user guides at all-guides.com

8
#$@[\]^‘{|}~ Refer to the ISO 646 Character Replacements chart
in your User’s Guide to view the character replacements for each
country.
USA (Default)
Belgium
Denmark
Finland
France
Germany/Austria
Great Britain
Italy
All manuals and user guides at all-guides.com

9
Note: For a complete list of country codes, see the User’s Guide
for your product.
Locked Link
If you link a scanner to a base using the Locked Link Mode,
other scanners are blocked from being linked if they are inad-
vertently placed into the base. If you do place a different scan-
ner into the base, it will charge the scanner, but the scanner will
not be linked.
To use a different scanner, you need to unlink the original scan-
ner by scanning the Unlink Scanner bar code.
Norway
Spain
Switzerland
Locked Link Mode
(Single Scanner)
All manuals and user guides at all-guides.com