REBEL OFF ROAD XPLOR BED RACK User manual

REBEL OFF ROAD XPLOR BED RACK TABLE MOUNT
FOR 2020+ JEEP GLADIATOR
INSTALLATION INSTRUCTIONS
PLEASE READ ALL INSTALLATION INSTRUCTIONS CAREFULLY AND IN
ENTIRETY PRIOR TO INSTALLING.
Approx. time required for installation: 1 hour
TOOLS REQUIRED:
1/2’’ DRIVE RATCHET
3/8’’ DRIVE RATHCET
7/16’’ SOCKET
9/16’’ SOCKET
5/32” HEX KEY
PARTS INCLUDED
QTY 2: CHANNEL
QTY 2: MID CHANNEL BRACKET
QTY 2: FRONT CHANNEL BRACKET
REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]
HARDWARE INCLUDED:
QTY 6: 3/8” CARRIAGE BOLTS
QTY 6: 3/8” NYLOCK NUTS
QTY 6: 3/8” FLAT WASHERS
QTY 6: 1/4” BUTTON HEAD BOLTS
QTY 6: 1/4” NYLOCK NUTS
QTY 6: 1/4” FLQTY 6: 1/4” FLAT WASHERS
QTY 2: SPRING LOADED CLEVIS
Step 1:
Lay out both channels, both mid channel brackets, and both front channel brackets on a
surface to assemble. The side of the channels with tabs on them go toward the rear of the
Jeep. Notice the hardware layout, the mid channel brackets utilize two carriage bolts and two
hex key bolts per side. The front channel brackets only utilize one carriage bolt and one hex
head bolt per side.

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]
Step 2:
Install the mid channel brackets to the channels. Place the mid channel Install the mid channel brackets to the channels. Place the mid channel
brackets along the holes in the side of the channel, and insert the 1/4”
button head bolt from the inside of the channel through the bracket. Secure
it with the 1/4” flat washers and nylock nuts. Refer to the photo below for
the orientation of the bracket. Do not completely tighten the hardware at
this time. You will have to make adjustments during installation.
Repeat this step for the other channel.

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]
Step 3:
Install the fInstall the front channel brackets to the ends of the channels. Install the
supplied 1/4” button head bolts from the inside of the channel, through the
channel bracket, and secure them with 1/4” flat washers and nylock nuts.
Notice there are two holes in each front channel bracket. You will only be
using the holes closest to the inside, indicated by the white arrows in the
image below. Refer to the images below for proper orientation of the
bracket. Do not fully tighten hardware.

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]
Step 4:
Not all tables are the same width, which is why we made this a modular
system to fit most applications.
Measu
Measure the width of the table you will be using for this mount. Using this
measurement, approximate the location of each bracket along the slotted
holes in your XPLOR Bed Rack System front and mid channels. This will help
you approximate the appropriate distance between the two table mount
channels for the width of your table.
When you identify the location along the bed rack whe
When you identify the location along the bed rack where you wish to install
your table mount channels, you can begin installing one side. Using the
supplied 3/8” carriage bolt, flat washer, and nylock nut, install the front channel
bracket to the front channel of your XPLOR Bed Rack System, inserting the
carriage bolt from top-down. Remember, although there are two square holes,
only one carriage bolt is needed to install each front channel bracket. Do not
tighten the hardware down fully to allow for adjustment.
Repeat this step for the other channel, ensuring you a
Repeat this step for the other channel, ensuring you are spacing the channels
correctly for your specific table width.

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]
Step 5:
Next, install the mid channel brackets to the mid channel on your XPLOR
Bed Rack System. Identify the location along the mid channel where you
will be installing each Table Mount channel, ensuring the channels are
parallel to each other.
Repeat the p
Repeat the process for the front channel mounts. Insert two 3/8” carriage
bolts through the top of the XPLOR Bed Rack mid channel, and secure the
mid channel brackets to it with the supplied flat washers and nylock nuts.
Notice you will use two sets of hardware per side on the mid channel
brackets. Do not fully tighten to allow for adjustment.

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]
Step 6:
Now that both channels are installed in place loosely, you can insert your
table into the channels to check for fitment. The ideal fitment should be
tight enough to securely hold the table in place without much play, but
loose enough to allow the table to slide in and out with ease.
When you have adjusted your channels to the p
When you have adjusted your channels to the proper fitment for your table,
begin fully tightening down all six carriage bolts and nylock nuts.
When the carriage bolts are tight, remove the table and fully tighten the six
button head bolts and nylock nuts.
After all the hardware is fully tightened, re-insert your table to check for
proper fitment. Make any final adjustments as necessary.
Install the two supplied spring loaded clevises th
Install the two supplied spring loaded clevises through the tabs on the rear
of each channel to keep the table from falling out while driving. These
clevises should be installed from top-down.

REBEL OFF ROAD | 23501 COMMERCE CENTER DR, SUITE A, LAGUNA HILLS, CA 92653
[phone] | [e-mail]