Rebound Products Non-Fold Manual

!
Non%Fold!Setup!
You$should$have:$$$$$$$$
2$–$End$Bars$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$12$–$corner$springs$
2$–$Midsections$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$4$;$Frame$pad$springs$
4$–$Chain$Braces$(Longest$braces)$$$$$$$$$$$$$$$$$$$$$$$$$4$;$webbing$springs$
4$–$Inner$leg$braces$(curved$tabs)$$$$$$$$$$$$$$$$$$$$$$$$$1$;$trampoline$bed$
4$–$Outer$leg$braces$(shortest$braces)$$$$$$$$$$$$$$$$$1$;$set$of$frame$pads$
2$–$Legs$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$106$;$H.P.$springs$
1$webbing$rectangle$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$10$–$pad$lifters$
For$ease$of$set$up$have$four$people.$
Add$a$little$grease$to$the$leg$tops$and$insert$into$the$midsections.$$
*You$should$try$to$start$by$having$a$level$surface$before$assembly.*$
When$the$legs$are$inserted$to$the$midsection$replace$the$screw$and$large$washer.$
Attach$the$Chain$braces$loosely$to$the$midsections$holes$which$are$15”$from$the$
center.$
Lift$the$ends$of$the$midsections$and$bolt$the$chain$brace$to$the$tabs$located$on$
the$legs$loosely.$$
$Do$the$same$with$the$other$side.$$When$complete$the$midsections$should$be$free$
standing.$$$

Spin$the$chain$braces$until$all$four$sides$are$approx$$$45$5/8”$from$the$level$
surface$measured$to$the$wiggle$wire.$$This$is$a$minimum$height$requirement.$$
Please$try$to$get$as$close$to$this$number$are$possible.$$The$main$importance$is$to$
have$the$trampoline$level.$$
$
When$all$four$sides$are$equal,$tighten$the$Chain$Braces.$$There$is$a$nut$on$one$side$
that$will$need$to$be$tightened$as$well.$
$
*It$is$important$to$have$the$midsections$level$before$completing$the$next$step*$
Loosely$bolt$the$leg$braces$to$the$legs$of$the$trampoline.$$$
The$straight$brace$goes$on$the$outside$of$the$tab$and$the$curved$brace$goes$on$
the$inside.$
Insert$the$Endbar$into$the$midsection$and$tighten$the$bolt.$$$Adjust$the$braces$and$
attach$to$the$Endbar$and$make$it$45$5/8”$to$the$wiggle$wire.$$$
Installing!the!String!Bed!
!
1)$Attach$the$corner;most$springs$first$using$corner$springs$(see$step$2),$on$
the$ends$of$the$bed,$and$adjust$the$border$rope$so$that$the$knot$at$the$end$
of$the$rope$is$lined$up$with$the$end$of$the$last$spring$clip.$Then$do$the$same$
for$ the$ sides.$ Note$ that$ the$ ropes$ on$ the$ long$ sides$ of$ the$ bed$ are$ about$
two$ inches$ longer$ than$ the$ bed$ in$ order$ to$ accommodate$ the$ initial$
stretching$of$the$bed$in$this$direction.$
$
2)$The$twelve$(12)$corner$springs$ are$ placed$ as$ shown.$ Do$ not$ put$ corner$
springs$elsewhere$on$the$bed$as$they$will$give$the$bed$a$hard$bottom,$and$
the$ corners$ will$ be$less$stable.$The$corner$springs$are$the$longer$fatter$

springs.$ IT! IS! CRUCIAL! TO! USE! CORNER! SPRINGS$with$your$performance$
springs$as$shown,$OTHERWISE$the$corners$will$be$soft$and$AN$ATHLETE$who$
lands$in$the$corner$or$very$near$the$edge$of$the$bed$MIGHT$FALL$OFF.$$$
$$$$$
Important!$ DO$ NOT$ to$ get$ too$far$ahead$of$the$helper$when$attaching$the$
springs.$$$
$
4)$ If$ the$ bounce$ seems$ too$ hard,$ extenders$ may$ need$ to$ be$ added.$ Check$
where$ the$ springs$ are$ the$ longest$ (stretched$ out$ the$ most),$ then$ add$
extender$hooks$between$the$springs$and$the$trampoline$frame$to$adjust$the$
tension.$(Expect$about$fifteen$(15)$inch$space$for$side$springs.)$
$
Note$that$under$normal$use$the$bed$will$increase$in$size,$slightly$and$
the$paint$will$wear$in$during$the$first$couple$weeks$under$tension.$Also$the$
springs$will$lose$some$of$tension$during$the$first$forty$40$hours$of$use$with$
heavy$or$powerful$athletes.$It$is$normal$that$a$brand$new$bed$will$feel$a$bit$
tight.$
$
WARNING! %$When$you$install$your$new$string$bed,$please$make$sure$that$
the$trampoline$ frame$ is$structurally$ sound$ and$ that$ there$ is$ at$ least$ 45.5”$
inches$of$clearance$from$the$bed$to$the$floor.$You$must$ensure$that$there$is$
nothing$ on$ the$ frame$ or$ anywhere$ else$ which$ could$ obstruct$ or$ interfere$
with$the$path$of$the$bed$at$all$travel$points.$Make$sure$that$your$frame$pads$
have$firm$foam$and$cover$the$frame$and$springs$of$the$trampoline.$$
3)$ Install$ the$ remaining$ springs$
on$ the$ ends$ working$ with$ a$
partner$ on$ the$ other$ end.$ Then$
align$ the$ side$ bed$ clips$ on$ the$
border$ rope$ and$ put$ the$ rest$ of$
the$springs$on$the$sides.$

Installing!the!Frame!Pads!Lifters!
$$$$$The$pad$lifters$might$need$adjustment$for$the$frame$pads$to$sit$at$the$
correct$height.$$$$To$install$the$pad$lifters$you$need$to$twist$the$Pad$lifter$so$
the$coil$is$parallel$to$the$frame.$$See$photos$
$

$

$
$
$
!
!

!
$

$
Photo!1!
!
$

Photo!2!
!
$

Photo!3!
!
!

Photo!4!
!
!

Photo!5!
!
!
!

Photo!6!
!
!
$
$

$
Photo!7!
!
!