Recordex iMMPad SE User manual

iMMPad SE Quick Start Guide
Classroom Technology Essentials.
Active/Write Status LED
The blue LED will flash when the
table is actively communicating with
the computer and ready to be used.
Sleep/Settings Button
The tablet will go into sleep mode after
several minutes of inactivity. Press this
button to wake up the tablet. Also use this
button to connect the tablet to the USB
receiver.
Low Battery LED
The red LED will light when battery
power is too low to use the tablet.
USB Plug (for wired power)
The tablet can be used even when the
batteries are drained by plugging the
tablet into a USB port on your computer.
NiMH Rechargeable Batteries
The tablet ships with pre-charged
NiMH rechargeable batteries (2xAA).
These provide many hours of use
between charges.
Battery Compartment (underside of tablet)
Power Switch
Pen
Use the pen as a pointing
device by writing with it over
the active area of the tablet.
Active Writing Surface
Using the pen on the active area will allow for wireless
control of your computer's pointer.
Media Shortcuts
Tap the media shortcuts with the pen tip to easily, scroll,
adjust volume, play, stop or skip audio or video tracks, and more.
USB Receiver
The USB receiver is
stored in the battery
compartment.
USING TABLET FOR FIRST TIME
1. Plug USB Receiver into Computer.
The drivers for the tablet will be installed
automatically. Just wait 15-45 seconds for
installation to complete.
battery compartment.
2. Insert the NiMH batteries.
The batteries are pre-charged and ready
to use.
3. Hold Down the Settings Button
Press the Setting Button and keep
holding down the button while
you switch on the tablet power..
zz
4. Switch on the Tablet.
Turn on the power swtich and the tablet
will connect to the USB Receiver and your
computer. The ACTIVE/WRITE LED will
start to blink blue.
5. Install Annotation Software
You can use your tablet now without
installing any additional software. For
maximum performance, however, we
recommend installing the InfoPen soft-
ware included on the iMMPad SE
software CD.
ENJOY!
SUPPORT: 478-237-5501 // [email protected]
Upper Pen Switch
XP - Scroll
Vista - Left Click
Win7 - Left Click
Lower Pen Switch
XP - Right Click
Vista - N/A
Win7 - Right Click (press & tap)
Pen Nib
XP - Tap to click
Vista - Tap to click
Tap & Hold to Right Click
Win7- Tap to click
Tap & Hold to Right Click

InfoPen Presenter Installation Guide
iMMPad SE
R
Driver Installs Automatically
The iMMPad SE does not require any drivers to be
preloaded. Simply plug in the USB receiver and
all version of Windows will automatically install
the correct drivers for the new hardware.
Install InfoPen Presenter
InfoPen Presenter is a powerful on screen annotation
program that allows for annotating a screen snapshot
as well as operating in three board modes: Blackboard,
Whiteboard, and Glass Board.
C
2010-2011 Recordex, USA, Inc.
Install InfoPen Recorder
InfoPen Recorder is a screen recording application that
will capture audio and video from your computer desktop.
NOTE: The software installs in a 30 day trial mode. To activate the
software: Click Start / Programs / InfoPen / Registration Wizard.
You will need to enter the software serial number printed on the
paper sleeve of this installation disc.
Classroom Technology Essentials.
To Install InfoPen Presenter & Recorder
simply insert the installation disc and use
the installation wizard to install the
software.
Registering the software. The software will install with a 30-day trial mode enabled. To
register and activate the software follow these steps:
1. Click Start
2. Click Programs
3. Click InfoPen
4. Click InfoPen Presenter
5. Click Registration Wizard
Follow these steps to complete the Registration Wizard:
A. Enter serial number (you can find this
number printed on the outside of the
paper sleeve of your install disc).
B. Enter your email address
C. Select InfoPen Presenter and Recorder
D. Enter personal information:
NOTE -- you may leave the default
information in each field if you do not
want to supply this information.
E. Contact Information - Optional
F. Activate the software:
- Active Online (will activate the
software through your Internet
connection)
- Send Mail (will send an email with the
registration information and you will
receive a response with instructions
for completing the registration
process.
NOTE: After registering you will receive
an email with your registration information.
If you selected the "Active Online" option
you can ignore the instructions in the
email. If you chose the send mail option
then you will need to follow the instructions
in the email to complete registration.
A user manual is included with InfoPen
Presenter and Recorder. You can access
these manuals under the Programs list on
your computer: Start/Programs/InfoPen.