red lion RL160U User manual

200567e 0902
OWNER'S
MANUAL
SUBMERSIBLE
UTILITY PUMP
RL160U
APPLICATION
This pump is suitable for portable applications where
the total head requirement (including pipe friction
losses) does not exceed the pump's maximum capabil-
ity. Also, the maximum solids size must not be greater
PRINTED IN
TAIWAN
BEFORE OPERATING OR
INSTALLING THIS PUMP,
READ THIS MANUAL AND
FOLLOW ALL SAFETY
RULES AND OPERATING
INSTRUCTIONS.
WARNING - ELECTRICAL PRECAUTIONS
All wiring, electrical connections, and system ground-
ing must comply with the National Electrical Code
(NEC) and with any local codes and ordinances. Em-
ploy a licensed electrician.
WARNING - RISK OF ELECTRICAL SHOCK
• Have an electrician provide electrical power to the
motor plug receptacle.
• Always disconnect plug from power source before
handling.
• This product is furnished with a three prong plug for
grounding, connect only to properly grounded recep-
tacle.
SAFETY CAREFULLY READ THESE SAFETY
MESSAGES IN THIS MANUAL AND ON
PUMP.
CAUTION
• Review instructions before operating.
SAFETY WARNINGS
• Do not under any circumstances remove ground plug.
• Keep electric plug dry.
• Do not lift pump using cord.
• Not investigated for use in swimming pool area.
• A ground fault interrupter (GFI) protected circuit is
recommended for use with any electrical appliance
operating in or near water.
than the pump capability. This pump is for use with
water only, NOT FOR USE IN EFFLUENT OR SEW-
AGE APPLICATIONS!
RL160U

2
MAINTENANCE
Your pump has been built to give many years of
satisfactory service. No regular maintenance is re-
quired since the pump is completely self lubricating.
The following routine checking procedure is recom-
mended to be carried out once a year and is especially
important for occasional use applications.
a) Check the power cords and electrical outlet for
damage or corrosion.
AIR LOCKING
If the pump is placed into the water while running, it will
air lock. This means that air is trapped in the pump,
preventing it from pumping water. To avoid this, always
FIG.1 TYPICAL INSTALLATION
INSTALLATION
Before installation, check your local electrical and
plumbing codes. These regulations are for your safety.
1) Location:
The pump should be located on a solid level foundation.
a) Do not suspend pump from electrical cord.
b) Do not suspend pump from discharge pipe.
c) Keep pump inlet screen clear.
2) WARNING
- RISK OF ELECTRICAL SHOCK
All connections must be made into a grounded outlet.
A ground fault interrupter (GFI) protected circuit is
recommended for use with any electrical appliance
operating in or near water.
The electrical power outlet required for this pump is a
separate 15 amp circuit of 115 volts, AC 60HZ, with a
proper fused switch in the line. This must be located
within 8 feet of the pump. The ground terminal on the
plug is provided for your protection. Do not remove.
Plug the pump cord into the 115 volt grounded service
and connect the discharge piping, your pump is then
ready for operation.
3) Discharge Piping - Rigid Pipe:
a) The pump has a threaded discharge opening.
b) PVC or ABS adapters may be used to adapt to
other sizes of pipe.
c) We recommend that you not reduce the discharge
pipe size, use as large as possible.
d) Keep piping length to a minimum (extra length
increases friction losses).
4) Discharge Piping - Garden Hose:
a) Thread garden hose adapter into pump. Note: Fine
threads go into pump, coarse threads are for gar-
den hose.
b) Attach garden hose, shorter hose lengths will allow
better flow from the pump.
place the pump in the water when it is off, and then plug
it in. If the pump does air lock, simply unplug it and then
plug it back in.

3
TROUBLE SHOOTING GUIDE
Trouble Probable Cause Corrective Action
Motor does not run Blown fuse Replace fuse
Tripped circuit Reset
Disconnected plug Reinstall
Corroded plug Clean prongs
Tripped overload Allow pump to cool, investigate cause (jammed
impeller)
Defective switch Replace switch
Defective motor Replace pump/repair
Float-improper position Check for freedom of movement
Motor hums but flow Impeller jammed Remove bottom plate and clean.
reduced or none at all Plugged check valve Remove valve, clean or replace
Partially blocked inlet Clean inlet
Line leak Repair
Worn impeller Replace pump/repair
Defective motor Replace pump/repair
SAFETY TIPS (ELECTRICAL)
1) Never make adjustments with the power connected.
Always disconnect your pump from the electrical outlet
before beginning any service procedures.
2) Do not stand on wet floor when servicing.
3) Do not put your finger into the fuse socket - it could be
fatal.
4) Never remove the round pin from your plug; this is the
ground and is there for your safety.
Red Lion
P.O. Box 429
Winnipeg, MB
R3C 3E4
Canada
Pump Hotline [phone])
www.redlionproducts.com
LIMITED RED LION WARRANTY
For 1 year from date of purchase, Red Lion will replace or repair for the original purchaser, free of charge, any part or parts,
found upon examination by any Red Lion Authorized Service Depot or by the Red Lion factory, to be defective in material or
workmanship or both. Equipment and accessories not manufactured by Red Lion are warranted only to the extent of the
original manufacturer's warranty. All transportation charges on parts submitted for replacement or repair under this warranty
must be borne by the purchaser. For warranty service see your nearest Red Lion Authorized Service Depot. THERE IS NO
OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE LIMITED TO 1 YEAR FROM PURCHASE AND TO THE EXTENT PERMITTED BY LAW.
LIABILITY FOR CONSEQUENTIAL DAMAGES UNDER ANY AND ALL WARRANTIES ARE EXCLUDED TO THE EXTENT
EXCLUSION IS PERMITTED BY LAW.
This warranty is an addition to any statutory warranty.