Redexim Easy Spread 1000 User manual

User Manual and Parts Book
Easy Spread
Model 1000/1500/2000
Serial number:
Translation of the original operating instructions
ATTENTION:
IT IS OF THE UTMOST IMPORTANCE TO READ THIS USER MANUAL
CAREFULLY PRIOR TO USING THE EASY SPREAD IN ORDER TO USE THE
MACHINE SAFELY AND TO OBTAIN THE BEST RESULTS.
1714 English 931.120.000

2
FOREWORD
Congratulations on your Easy Spread purchase! For safe and long-lasting operation of the
Easy Spread, it is necessary to read and to understand this user manual. It is impossible to
work safely with this machine without complete knowledge of the content of the user manual.
The Easy Spread is not a machine that works independently. It is the user’s responsibility to
use the correct tractor. The user must also check the tractor/Easy Spread combination on
safety aspects such as noise level, user instructions and risk analysis.
The Easy Spread is solely intended for grass fields or areas where grass can grow.
The following pages deal initially with the general safety instructions. Every user should know
these safety instructions and apply them. At the end of this page, a registration card is
inserted. This registration card should be returned to us in order to deal with potential future
claims.
This user manual lists many instructions that are numbered in sequence. You should follow
this sequence. A is an indication of a safety instruction. A means a tip and/or note.
All information and technical specifications provided at the moment that this document is
published are the most recent ones. Design specifications may be changed without prior
notice.
This document is a translation of the original operating instructions.
Upon request, the original operating instructions are available in Dutch.
WARRANTY CONDITIONS
AT THE TIME OF DELIVERY THE EASY SPREAD IS GUARANTEED AGAINST MATERIAL
DEFECTS.
THIS WARRANTY IS VALID FOR A PERIOD OF 12 MONTHS FROM THE PURCHASE
DATE.
EASY SPREAD WARRANTIES ARE SUBJECT TO THE ‘GENERAL CONDITIONS FOR
SUPPLY OF PLANT AND MACHINERY FOR EXPORT, NUMBER 188’ THAT ARE
PUBLISHED UNDER THE AUSPICES OF THE UNITED NATIONS ECONOMIC
COMMISSION FOR EUROPE.
REGISTRATION CARD
For your own information, fill in the table below:
Serial number of the
machine
Dealer name
Date of purchase
Remarks

3
SAFETY INSTRUCTIONS
Figure 1
The Easy Spread is designed for safe use. This
can only be achieved if you completely follow the
safety instructions described in this manual.
Read and understand (figure 1) the manual
before you use the Easy Spread.
If the machine is not used as described in this
manual, this can result in injuries and/or damage
to the Easy Spread.
(1) The Easy Spread is only intended for gritting fine-grained materials (sand, pebble stones
and the like).
Any other use is improper. The manufacturer will not accept any liability for damage
resulting from improper use. All risks occurring with this are entirely at the expense of
the user.
Following the use, maintenance and repair instructions prescribed by the manufacturer
is also considered proper use of this machine.
The manufacturer will not accept any liability for unprofessional use and its resulting
damage. All risks occurring with this are entirely at the expense of the user.
Following the use, maintenance and repair instructions prescribed by the manufacturer
is also considered professional use of this machine.
Inspect the area to be treated before using the Easy Spread. Remove loose obstacles
and avoid irregularities.
(2) The Easy Spread is manufactured according to the latest technical understanding and is
safe to use.
When unskilled people use, maintain or repair the machine, this could result in injuries to
the user and to third parties. This must be avoided!
Always use the Easy Spread in combination with the correct tractor as described
in the technical data.
(3) All persons assigned to operate, maintain and repair the Easy Spread by the owner must
completely read and understand the operation manual and in particular the chapter of
Safety Instructions.
The user is responsible for a safe Tractor/Easy Spread combination.This entire
combination must be tested for noise, safety, risk and user friendliness. User
instructions should also be drafted.
(4) The user is obliged to check the Easy Spread for visible damage and defects before
using it.
Modifications to the Easy Spread (including its operations) that have a negative impact
on safety must be rectified immediately.
For safety reasons it is in principle not permitted to make changes or adjustments to the
Easy Spread (except those approved by the manufacturer).

4
If modifications to the Easy Spread have been made, then the current CE marking is
cancelled. The person that has made these modifications has to apply for a new CE
marking himself.
Check the Easy Spread for loose bolts, nuts and components before every operation.
If present, check the hydraulic pipelines regularly and replace these when the hydraulic
pipelines are damaged or appear old. The pipelines that are replaced should comply with
the technical requirements of the manufacturer.
If a hydraulic installation is present, you should always make it pressure-free before
working on this installation.
NEVER use the Easy Spread in the absence of protective guards and safety stickers.
NEVER crawl under the Easy Spread.
If necessary, tilt the Easy Spread.
NEVER step off the tractor while the motor is running.
When carrying out maintenance, adjustments and repairs, it is necessary to block the
Easy Spread in order to prevent it from sinking away, driving off and/or sliding off.
Always switch off the tractor motor and take the tractor’s key out of the ignition in
carrying out maintenance, adjustments and repairs (Figure 2).
Figure 2
Use only original Easy Spread parts for maintenance or repairs because of the safety of
the machine and of the user.
Only authorised technical personnel may carry out repairs to the Easy Spread.
Keep a record of the repair activities.
(5) The general applicable health & safety (Dutch: ARBO) regulations must also be followed
in addition to the instructions in this user manual.
Relevant traffic regulations also apply in case of using public roads.
Transporting persons is not permitted!
Do not use the Easy Spread in the dark, in heavy rain/storm or on slopes with an
angle larger than 20 degrees.

5
(6) All persons that are going to operate the Easy Spread must be familiar with all its
functions and control elements before starting any work activities.
Attach the Easy Spread to the towing vehicle according to the regulations. (Danger of
injuries!) Check whether you have a clear field of vision – both close by and far away –
before you depart.
Both sideboards of the Easy Spread have a safety sticker (figure 5) that have the same
information.This safety sticker must always be clearly visible and legible and must be
replaced if they have become damaged.
During operation, NO persons are allowed within the danger zone of the Easy
Spread, because there is danger of physical injuries caused by moving components
(Figure 3).
Keep a distance of minimum 4 meter (13 feet)! (Figure 4)
Figure 3
Figure 4
Pay attention to the permitted lifting capacity of the towing vehicle.
Dress appropriately. Wear sturdy shoes with steel toecaps, long trousers and tie up long
hair. Do not wear loose clothing.
(7) Location of the safety stickers (Figure 5).
Figure 5
Used oil/grease is harmful to the environment. Dispose of these substances according to the
regulations that apply in your location.

6
EU DECLARATION
We -
Redexim BV,
Utrechtseweg 127,
3702 AC Zeist, Holland
– declare entirely under our own responsibility that the product:
EASY SPREAD WITH MACHINE NUMBER AS INDICATED ON THE MACHINE AND IN
THIS MANUAL
to which this declaration relates is according to the stipulation of the 2006/42/EC directive for
machines as well as the following standards: NEN-EN-ISO 12100 : 2010 and NEN-EN-ISO
13857 : 2008.
Zeist, 18/07/13
A.C. Bos
Manager Operations & Logistics
Redexim Holland

7
TABLE OF CONTENTS
WARRANTY CONDITIONS....................................................................................2
REGISTRATION CARD..........................................................................................2
SAFETY INSTRUCTIONS......................................................................................3
EU DECLARATION ................................................................................................6
1.0 TECHNICAL DATA ....................................................................................8
2.0 GENERAL DESCRIPTION.........................................................................8
3.0 FIRST INSTALLATION – TAKING THE MACHINE OFF THE
PALLET/GETTING IT READY FOR USE...................................................9
4.0 ATTACHING THE MACHINE TO THE TRACTOR...................................10
5.0 OPERATING THE EASY SPREAD..........................................................12
5.1 OPERATING THE EASY SPREAD TIPPING BUCKET............................12
5.2 OPERATING THE GRITTING CYLINDER / AGITATOR & DOSE LID .....12
6.0 LOADING THE EASY SPREAD...............................................................13
7.0 DRIVING SPEED.....................................................................................14
8.0 USING THE EASY SPREAD....................................................................14
9.0 START/STOP PROCEDURE...................................................................14
10.0 TRANSPORTING THE EASY SPREAD ..................................................15
11.0 DISCONNECTING THE EASY SPREAD.................................................16
12.0 TROUBLE SHOOTING (PROBLEM ANALYSIS).....................................17
13.0 MAINTENANCE.......................................................................................18
13.1 GREASE POINTS.....................................................................................19
14.0 CLEANING THE EASY SPREAD.............................................................19
15.0 CHANGE WHEELS..................................................................................20
16.0 CHAIN TENSION.....................................................................................21

8
1.0 TECHNICAL DATA
Model 1000 1500 2000
Working width 1.0 m
1.5 m 2.0 m
Tractor speed
Max. 12 km/h (7,5 mph), depending on
the type of tractor
and the condition of
the ground.
Max. 12 km/h (7,5
mph), depending on
the type of tractor
and the condition of
the ground.
Max. 12 km/h (7,5
mph), depending on
the type of tractor
and the condition of
the ground.
Weight 494 kg (1090 lbs)
590 kg (1300 lbs) 700 kg (1543 lbs)
Container content 0,58 m3(20.5 ft3)
0,87 m3(30.7 ft3) 1,17 m3(41.3 ft3)
Machine size ( L x W x H) 1,23 x 1,18 x 1,74 m
48,4”x 46,5”x 68,5” 1,23 x 1,68 x 1,74 m 48,4”x 66,1”x 68,5” 1,23 x 2,18 x 1,74 m 48,4”x 58,8”x 68,5”
Gritting thickness 0-20 mm
Depending on the
driving speed,
position of the dose
lid and position of
the dose regulator.
0-20 mm
Depending on the
driving speed,
position of the dose
lid and position of
the dose regulator.
0-20 mm
Depending on the
driving speed,
position of the dose
lid and position of the
dose regulator.
Recommended tractor
Minimum lifting capacity
60 hp
1100 kg (2865 lbs)
60 hp
1300 kg (2865 lbs)
80 hp
2000 kg (4410 lbs)
Three-point connection Cat. 1 & 2
Cat. 1 & 2 Cat. 1 & 2
Minimum loading capacity
of the tractor 12 l/min 12 l/min 12 l/min
Minimum pressure 70 bar 70 bar 100 bar
Necessary connections 2 x double-acting 2 x double-acting 2 x double-acting
Standard components -Tipping bucket
-Powered gritting
cylinder
-Agitator
-Continuously
adjustable dose lid
-Adjustable legs
-Tipping bucket
-Powered gritting
cylinder
-Agitator
-Continuously
adjustable dose lid
-Adjustable legs
-Tipping bucket
-Powered gritting
cylinder
-Agitator
-Continuously
adjustable dose lid
-Adjustable legs
2.0 GENERAL DESCRIPTION
The Easy Spread is only intended for gritting fine-grained materials such as sand, pebble
stones and the like.
The tipping bucket can scoop and fill the gritting material while the dose lid can afterwards
grit the material on the ground. This dose lid can be adjusted continuously so that the gritting
quantity can be accurately adjusted.

9
3.0 FIRST INSTALLATION – TAKING THE MACHINE OFF THE
PALLET/GETTING IT READY FOR USE
Figure 6
The machine is placed on the pallet. To remove the pallet and to place the machine on the
ground, you take the following steps (see Figure 6):
NEVER CRAWL UNDER THE MACHINE!
1. Attach a cable to the upper 3-point (1) and at the hoisted supports (2) at both sides of
the machine.
Make sure that the cable/crane/lift can hoist minimum 2x the weight of the
machine. (machine weight see Chapter 1.0 Technical data)
2. Lift the machine so the cables come under tension.
3. Remove the bottom 3-point connection
4. Lift the machine off the pallet (3) and pull the pallet from under the machine.
5. Lower the machine controlled and calmly until it stands completely on the ground.
CAREFUL: KEEP YOUR DISTANCE; THE MACHINE CAN SLIDE!
6. Remove the cable.
7. The machine is no ready for use.
8. Connect the machine to the tractor (please refer to Chapter 4.0).

10
4.0 ATTACHING THE MACHINE TO THE TRACTOR
Checking procedure before starting to attach the Easy Spread:
Check the Easy Spread for visually discernable damage and repair this if safe
operation of the machine is no longer guaranteed.
Check whether all the nuts and bolts are tight.
Check whether all safety stickers are present on the machine and are not damaged.
NEVER use the machine without these items.
Figure 7
The Easy Spread can be attached to the tractor by means of the 3-point attachment.
The procedure is as follows (see Figure 7):
1. Remove the locking pins (1 & 2) and the pins (3 & 4).
2. Drive the tractor carefully backwards so that the lower connecting arms (5) can be
attached to the frame.
Make sure that the tractor is blocked well and cannot move on its own
accord!
Switch off the tractor before descending!
3. Using the locking pins (1) and the pins (3), connect the lower connecting arms (5)
with the bottom 3-point connection located on the frame.
4. Set the stabilizer of the tractor to 100 mm lateral stroke.
5. Mount the top rod (6) of your tractor and turn it outward until it reaches the same
height as the 3-point stop connection of the Easy Spread.
6. Connect the top rod (6) to the frame with the pin (4); secure the pin (4) with the
supplied locking pin (2).
7. Screw in the top rod (6) so that the adjustable legs (8) are just released.

11
8. Attach the hydraulic hoses to the tractor (7). Make sure that hoses that go together
are attached to the same connection. The hoses for tipping the bucket should be
attached to one connection, these are the small hoses. The hoses for regulating the
gritting quantity should also be attached to one connection, these are the big hoses.
(figure 8).
9. Lift the machine.
10.Remove the adjustable legs (8) and mount them to the frame (figure 8).
Make sure that all securing pins are locked before lifting the Easy Spread!
Figure 8

12
5.0 OPERATING THE EASY SPREAD
Figure 9
Operating the Easy Spread is divided in two parts, namely the operation of the bucket and
the operation of the gritting cylinder.
Make sure that the two hydraulic hoses of each part are attached to a double-acting valve on
the tractor.
5.1 OPERATING THE EASY SPREAD TIPPING BUCKET
The Easy Spread bucket can be tipped to 90to scoop gritting material. Tipping of the bucket
can be regulated on the tractor after the hydraulic hoses have been attached to the tractor.
5.2 OPERATING THE GRITTING CYLINDER / AGITATOR &
DOSE LID
The hydraulic hoses for operating the gritting cylinder / agitator and dose lid should be
attached to the other double-acting valve. The direction of the volume flow from the tractor
makes the gritting cylinder/agitator turn and subsequently opens the dose lid. If the direction
is reversed, the gritting cylinder/agitator will stop turning and the dose lid will close.
The speed of the gritting cylinder/agitator can be adjusted with a regulating valve (1) (figure 9).
9).
The opening of the dose lid can be adjusted by turning the stop bolts (2) on the bucket so
that the dose lid is opened as desired. Use indication strip for comparison.

13
6.0 LOADING THE EASY SPREAD
Loading the Easy Spread is done by lowering the bucket and scooping the gritting material
(Figure 11).
Figure 10
The procedure is as follows (Figure 10):
1 Drive the machine in a raised position to the gritting material to be used.
2 Lower the wheels of the Easy Spread to the ground.
3 Position the Easy Spread bucket horizontally.
4 Drive the tractor with the bucket backwards into the material to be loaded.
5 When the bucket hits the material. Slowly tilt the bucket upwards
Lifting too much material can damage the Easy Spread!
6 Load the bucket by rotating the bucket back to a vertical position.
7 Carefully lift the Easy Spread with the lifting device of the tractor.
Mount front weights to the nose of the tractor in case of doubting the
stability of the tractor – Easy Spread combination!
When the machine is raised off the ground, the front axle of the tractor
has to support minimum 20% of its weight!

14
7.0 DRIVING SPEED
For safety reasons the driving speed of the Easy Spread is limited to 12 km/h (7,5 mph), but
in reality you will have to determine the maximum driving speed depending on the desired
gritting image.
8.0 USING THE EASY SPREAD
Before using the Easy Spread in a location, you should check the following items:
1. Are there loose objects in the field? First remove these objects.
2. Are there slopes? The maximum slope is 20 degrees for the Easy Spread. Always go
from top to bottom.
3. Is there danger of flying objects (e.g., golf balls) that distract the attention of the driver? If
so, the Easy Spread CANNOT be used.
4. Is there danger of sinking/sliding away? If so, postpone using the Easy Spread.
5. If the soil is frozen or very wet, postpone the activities until conditions improve.
9.0 START/STOP PROCEDURE
The start procedure is VERY important. If this procedure is not executed as described below,
it might result in serious damage to the machine.
Figure 11
The start procedure is as follows (Figure 11):
1. Have a good look at the Easy Spread and see whether all components function properly.
If not, first solve the problems before using the Easy Spread.
2. Connect the Easy Spread to the tractor as described in Chapter 4.0.
3. Determine the desired rotating speed of the gritting cylinder.
4. Lift the Easy Spread.

15
5. Drive to the spot where the processing should take place and stop the tractor.
6. Engage the tractor in the correct gear.
7. Lower the Easy Spread to the ground in a smooth movement.
8. Start driving the tractor and operate the hydraulic valve of the gritting cylinder/agitator so
that it begins to grit.
9. Accelerate the driving speed until you achieve the desired gritting result.
Work in straight lines; working in bends causes damage to the surface
that should be processed.
Stopping occurs as follows:
1. Operate the hydraulic valve so the gritting stops and the dose lid closes.
2. Stop the tractor.
3. Lift the Easy Spread.
4. Go to the next location and start all over again as described in this chapter.
10.0 TRANSPORTING THE EASY SPREAD
The user is responsible for transporting the Easy Spread in back of the tractor on public
roads. Verify the national legislation regarding the regulations.
On open fields while the machine is raised, the maximum permitted speed is 12 km/h (7.5
mph) due to the weight of the Easy Spread.
A higher speed can be dangerous for the driver and/or the public and can even damage the
machine.
When the machine is raised off the ground, the front axle of the tractor has to
support minimum 20% of its weight!

16
11.0 DISCONNECTING THE EASY SPREAD
Figure 12
The machine can be detached from the tractor in the following manner (Figure 12):
1. Drive the Easy Spread to a parking area with a firm/flat surface.
2. Remove the adjustable legs (1) from the frame and reattach these to the bucket.
3. Lower the Easy Spread controlled and calmly until it stands completely on the
ground.
Make sure that the tractor is blocked well and cannot move on its own
accord!
Switch off the tractor before descending!
Make sure that the Easy Spread stands firmly on the ground and is
blocked against sliding before descending from the tractor!
4. Disconnect the hydraulic hoses.
5. Release the top rod (2).
6. Take the locking pin (3) out of the pin (4) and pull the locking pin out of the top rod
connection.
7. Take the locking pins (5) out of the pins (6) and pull the locking pins out of the Easy
Spread frame so that the bottom lifting arms (7) of the tractor are released.
Make sure that the Easy Spread is stable!
8. Start the tractor and drive off.

17
12.0 TROUBLE SHOOTING (PROBLEM ANALYSIS)
Problem Possible cause Solution
Gritting cylinder /
Agitator does not
rotate or hardly
rotates.
Hydraulic hoses are not
attached correctly to the
tractor.
Attach the hoses correctly to
the tractor.
Rotating speed of the cylinder
is too low. Turn up the speed control button on the frame.
Agitator blocked Clear blockade
Pollution/ defect hydraulic
system Repair or change parts
The chain broke. Check the chain.
The dose lid will not
open or will not open
far enough.
Stop bolts are screwed too
loose. Further screw in the stop bolts.
Gritting material does
not come out the
dose lid.
Gritting material is too wet. Use dry gritting material.
The dose lid does not open far
enough. Adjust stop bolts so that the dose lid can open more.
The bucket will not
tip. Hydraulic hoses are not attached correctly to the
tractor.
Attach the hoses correctly to
the tractor.

18
13.0 MAINTENANCE
Only authorised technical personnel may carry out repairs and adjustments to the Easy
Spread due to the safety of the machine and the user.
Use only original Easy Spread parts for maintenance or repairs because of the safety of the
machine and of the user.
Time schedule Check point Method
Before every use Check for loose bolts/nuts. Tighten loose bolts/nuts.
After every 20 working
hours
Check the agitator for bended
pins. Repair or replace the pins.
Check for loose bolts/nuts. Tighten loose bolts/nuts.
Presence and readability of
the safety stickers (see figure
5)
Replace if these are
damaged.
Grease the bearings +
cylinders Use EP2 lubrication.
Check the tyre pressure. Tyre pressure should be 1.5
bar (22 psi).
After every 100
working hours
Check hydraulic system Repair or replace if these are
damaged.
Check chain tension Tighten is needed
(see Chapter 16)
Grease chain Use EP2 lubrication.

19
13.1 GREASE POINTS
On the machine are various lubrication points. In (fig. 13) lists the different points displayed.
Lubricate these points according to the indicated schema in Chapter 13.1. All cylinders are
provided with greasing points, these should all be lubricated.
Fig. 13
14.0 CLEANING THE EASY SPREAD
Here are the cleaning instructions in order to keep the Easy Spread in tip-top condition.
NEVER spray the bearing seals with a high-pressure pistol.
Do NOT use aggressive soap or cleaning agents.
NEVER operate the Easy Spread while cleaning it.
Make sure that the machine is stable and that it cannot sink or slide.
Make sure that the safety stickers are always clearly readable.

20
15.0 CHANGE WHEELS
In case of a leaky or damaged wheel, the wheel should be repaired or replaced. This can be
done in the following manner:
1 Raise the Easy Spread ± 20 cm (8 ") from the ground. By means of the lifting
device of the tractor or with cables.
Make sure that the tractor is blocked well and cannot move on its own
accord!
Switch off the tractor before descending!
Make sure that the Easy Spread stands firmly on the ground and is
blocked against lowering before removing the tires!
2 Loosen the bolts (1) and nuts (2) of the designated wheel set.
!! The wheel set is now loose and can fall down, make sure nobody is under
the wheel set as the bolts and nuts are los loosened!!
3 Lower the wheel set. The entire wheel set is now loose.
4 To remove the wheel from the axle, loosen the securing screw (4) off the axle support.
The wheel and the axel support can now be removed from the axel.
5 Repair or replace the wheel.
Fig. 14
6 When the wheel is repaired or replaced it can be mounted again.
7 Mount he wheel and the axle support on to the axle. Secure the axle support by
tightening the screw (4)
8 Slowly rais the axle support on to the bolts. Make sure the slot hols are pointed
upwards.
9 Tighten the nuts (2) and bolt (1).
!! Make sure the nuts and bolts are tightend properly !!
10 Now slowly lower the Easy Spread on to the ground. The Easy Spread is now ready
for use.