Redline Communications RedMAX User manual

70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 1 of 55
am
RedMAXTM
Outdoor Wireless Access
Subscriber Modem
User Manual

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 2 of 55
Copyright Information
All rights reserved September 7, 2007. The information in this document is proprietary to
Redline Communications Inc. This document may not in whole or in part be copied,
reproduced, or reduced to any medium without prior consent, in writing, from Redline
Communications Incorporated.
Contact Information:
Redline Communications Inc.
302 Town Centre Blvd. Suite 100
Markham, ON
Canada L3R 0E8
Web site: http://www.redlinecommunications.com
Sales Inquiries:
North American [email protected]
Toll-free sales 1-866-633-6669
International [e-mail]
Support: www.redlinecommunications.com/support/support_portal.html
Document Control:
70-00057-01-01-RedMAX_Subscriber_Outdoor_SU-O_UserManual-FCC-
20070907a.doc
Disclaimer
The statements, configurations, technical data, and recommendations in this document
are believed to be accurate and reliable, but are presented without express or implied
warranty. Additionally, Redline makes no representations or warranties, either expressed
or implied, regarding the contents of this product. Redline Communications shall not be
liable for any misuse regarding this product. The information in this document is subject
to change without notice.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 3 of 55
TABLE OF CONTENTS
1Important Safety Notices........................................................................7
1.1 Safety Warnings........................................................................................7
1.2 Important Warning Symbols......................................................................7
1.3 CSA Information........................................................................................8
1.4 Information For Use In Canada.................................................................8
1.5 FCC Notice................................................................................................9
1.6 FCC Certified Antennas ............................................................................9
1.7 Frequency Selection................................................................................10
1.7.1 General................................................................................................10
1.7.2 R&TTE Directive 1999/5/EC Statements.............................................10
1.8 WEEE Product Return Process...............................................................12
1.9 Important Service Information ................................................................. 13
2Overview ................................................................................................ 14
2.1 Features..................................................................................................15
2.1.1 IEEE 802.16 WiMAX Compliance .......................................................15
2.1.2 PHY Specification................................................................................15
2.1.3 Time Division Duplexing (TDD)...........................................................15
2.1.4 Coding Rate.........................................................................................15
2.1.5 Modulation...........................................................................................15
2.1.6 Reed Solomon Error Correction..........................................................16
2.2 Deployment Models.................................................................................16
2.2.1 PTP Deployment .................................................................................16
2.2.2 PMP Deployment.................................................................................16
2.2.3 Non Line-of-Sight.................................................................................16
2.2.4 Channelization.....................................................................................17
2.3 Service Flows..........................................................................................18
2.3.1 Service Flow Classification..................................................................18
2.3.2 Dynamic Service Addition.................................................................... 18
2.3.3 Uplink Service Flow Scheduling..........................................................18
2.3.4 Downlink Service Flow Scheduling...................................................... 19
3Outdoor Subscriber Features............................................................... 20
3.1 Integrated Antenna (SU-OIA)..................................................................20
3.2 Non Integrated Antenna (SU-ORF).........................................................21
3.3 Subscriber Connections and Controls.....................................................22
3.3.1 Ethernet Port (and Cable).................................................................... 22
3.3.2 RF Port................................................................................................22
3.3.3 Grounding Connection.........................................................................22
3.3.4 PoE (Power over Ethernet) Power Adaptor.........................................23
3.4 Mounting the Outdoor Subscriber ...........................................................24
3.4.1 Outdoor Subscriber with Integrated Antenna ......................................24
3.4.2 Outdoor Subscriber with External Antenna .........................................25
3.4.3 Antenna Alignment..............................................................................25
4CLI Commands......................................................................................26

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 4 of 55
4.1 Introduction..............................................................................................26
4.2 CLI Modes...............................................................................................26
4.2.1 Telnet Connection ...............................................................................26
4.2.2 Root Commands..................................................................................27
4.3 Mode Commands....................................................................................28
4.3.1 boardConfig - Board Setup Commands ..............................................29
4.3.2 bsIdTable - Base Station ID Table Commands................................... 30
4.3.3 diagStatistics - Diagnostic Statistics....................................................31
4.3.4 ethTag - Ethernet Tagging................................................................... 33
4.3.5 installedVer - Installed Version............................................................34
4.3.6 ipAddress - IP Address Commands ....................................................35
4.3.7 loadImage - Download and Activate Software Image..........................36
4.3.8 modThresh - Modulation Threshold..................................................... 37
4.3.9 monitor - Monitor Mode .......................................................................38
4.3.10 phyConfig - Physical Layer Configuration ...........................................39
4.3.11 privacySS - Privacy Commands..........................................................40
4.3.12 reset - Reset Command ......................................................................40
4.3.13 rfConfig - RF Setup Commands..........................................................41
4.3.14 set - Set Commands............................................................................42
4.3.15 show - Show Commands.....................................................................43
4.3.16 softwareUpdate - Software Update Commands.................................. 44
4.3.17 status - Status Information...................................................................45
5Appendices............................................................................................46
5.1 System Technical Specifications.............................................................46
5.2 Receive Sensitivity .................................................................................. 47
5.3 Subscriber Log Messages.......................................................................48
5.4 Upgrade Subscriber ................................................................................ 52
5.4.1 FTP Server.......................................................................................... 52
5.4.2 Upgrade Path ......................................................................................52
5.4.3 Connection to Subscriber....................................................................52
5.4.4 Update Software Procedure................................................................ 53

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 5 of 55
LIST OF FIGURES
Figure 1: Notices - WEEE Logo..........................................................................12
Figure 2: Intro - RedMAX Subscriber Outdoor System.......................................14
Figure 3: System - PTP Line of Sight Deployment..............................................16
Figure 4: System - Fresnel Zone......................................................................... 17
Figure 5: System - Non-Line of Sight Deployment..............................................17
Figure 6: SU-OIA System Features ....................................................................20
Figure 7: SU-ORF System Features...................................................................21
Figure 8: Outdoor Ethernet Cable - Cable Connection ....................................... 22
Figure 9: Optional Redline-Supplied PoE (Power-over-Ethernet) Power adaptor23
Figure 10: SU-OIA System Connections Diagram..............................................24
Figure 11: SU-ORF System Connections Diagram.............................................25
Figure 12: Subscriber CLI Interface - Login Dialog.............................................27

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 6 of 55
LIST OF TABLES
Table 1: Subscriber Station Antennas...................................................................8
Table 1: R&TTE - Community Language CE Declarations.................................10
Table 2: Notices - R&TTE: Countries of Use (3.4 GHz & 3.6 GHz) ....................12
Table 3: System - PoE Ports...............................................................................23
Table 4: System - Ethernet Data Port Link/Act LEDs..........................................23
Table 5: CLI - Command Groups........................................................................26
Table 6: CLI - Root Mode Commands ................................................................27
Table 7: CLI - Root Mode Commands ................................................................28
Table 8: CLI - boardConfig - Board Commands..................................................29
Table 9: CLI - bsIdTable - Base Station ID Commands......................................30
Table 10: CLI - diagStatistics - Diagnostic Statistics Commands........................31
Table 11: CLI - ethTag - Ethernet Tagging Commands......................................33
Table 12: CLI - installedVer - Installed Version Commands................................34
Table 13: CLI - ipAddress - IP Address Commands ...........................................35
Table 14: CLI - modThresh - Modulation Threshold Commands........................37
Table 15: CLI - monitor - Monitor Mode .............................................................. 38
Table 16: CLI - phyConfig - Physical Layer Commands .....................................39
Table 17: CLI - privacySS - Privacy Commands................................................. 40
Table 18: CLI - reset - Reset Commands ...........................................................40
Table 19: CLI - rfConfig - Radio Frequency Commands.....................................41
Table 20: CLI - set - Modify Subscriber Parameters...........................................42
Table 21: CLI - show - Show Commands ...........................................................43
Table 22: CLI - softwareUpdate - Software Update Commands......................... 44
Table 23: CLI - status - Status Commands.........................................................45
Table 24: Specifications - Outdoor Wireless Subscriber Modem........................46
Table 25: Reference - RedMAX Subscriber Receive Sensitivity.........................47
Table 26: Troubleshooting - Event Log Messages.............................................. 48

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 7 of 55
Chapter
1
1
1 I Im mp po or rt ta an nt t S Sa af fe et ty y N No ot ti ic ce es s
Models This manual describes features and operation of the outdoor SU-OIA/SU-ORF
(SU-O) wireless subscriber modem.
1.1 Safety Warnings
1. Installation of the system must be contracted to a professional installer.
2. Read this user manual and follow all operating and safety instructions.
3. PoE (Power over Ethernet) power adaptor caution:
PoE Power Adapter Caution
Warning to Service Personnel: 48 VDC
Standard Ethernet equipment may be damaged if connected directly to the 'Data +
Power Output' port of a PoE power adaptor.
4. The power requirements are indicated on the product-marking label. Do not exceed
the described limits.
5. Use only a damp cloth for cleaning. Do not use liquid or aerosol cleaners. Disconnect
the power before cleaning.
6. Disconnect power when unit is stored for long periods.
7. The outdoor unit must not be located near power lines or other electrical power
circuits.
8. The system must be properly grounded to protect against power surges and
accumulated static electricity. It is the user’s responsibility to install this device in
accordance with the local electrical codes: correct installation procedures for
grounding of the outdoor unit, mast, lead-in wire and discharge unit, location of
discharge unit, size of grounding conductors and connection requirements for
grounding electrodes.
9. Keep all product information for future reference.
1.2 Important Warning Symbols
The following symbols may be encountered during installation or troubleshooting. These
warning symbols mean danger. Bodily injury may result if you are not aware of the safety
hazards involved in working with electrical equipment and radio transmitters. Familiarize
yourself with standard safety practices before continuing.
Electro-Magnetic Radiation High Voltage

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 8 of 55
1.3 CSA Information
1. The equipment must be properly grounded according with NEC, ICEC, CEC, and
others, and other local safety code and building code requirements.
2. To meet the over-voltage safety requirements on the telecommunications cables, a
minimum 26 AWG telecommunication line cord must be used.
Pour être en conformance avec les exigences finies de sûreté de sur-tension sur les
câbles de télécommunications un fil de télécommunication ayant un caliber minimum
de 26 AWG doit être utilisé.
3. Reminder to all the broadband wireless system installers: Attention to Section 820-40
of the NEC which provides guidelines for proper grounding, and in particular,
specifies that the cable ground shall be connected to the grounding system of the
building as close to the point of cable entry as is practical.
1.4 Information For Use In Canada
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause
undesired operation of the device.
IMPORTANT NOTICE: IC Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. To maintain compliance with IC RF exposure compliance
requirements, please avoid direct contact to the transmitting antenna during transmitting.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
SU-OIA (integrated antenna): A separation distance of 20 cm or greater should be
maintained between persons and the antenna of the SU-OIA during device operation.
SU-ORF (external antenna): A separation distance of 50 cm or greater should be
maintained between persons and the antenna of the SU-ORF during device operation.
Table 1:Subscriber Station Antennas
Order Number DEG Gain (dBi) GHz Type Polarization
A2014ARF 13.5 20 3.3 - 3.8 Panel Vertical or
Horizontal
A1815MTS 15
16.5
18.5
18
3.3-3.4
3.4-3.7
3.7-3.8 Panel Vertical or
Horizontal
A2408MTF 8 24 3.3-3.8 Panel
Vertical or
Horizontal

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 9 of 55
1.5 FCC Notice
1. The Model SU-O and its antenna (SU-ORF only) must be professionally installed.
2. WARNING -- FCC RF Exposure Warnings
To satisfy FCC RF exposure requirements for RF transmitting devices, a minimum
distance of 25 cm should be maintained between the antenna of this device and
persons during device operation. To ensure compliance, operation at closer than this
distance is not recommended. The antenna used for this transmitter must not be
collocated in conjunction with any other antenna or transmitter.
3. Operation is restricted to the 25 MHz band 3.650-3.675 GHz (restricted contention
based protocol for WiMAX devices).
4. FCC Information to Users @ FCC 15.21 & 15.105:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
5. Warning: Changes or modifications not expressly approved by Redline
Communications could void the user’s authority to operate the equipment.
4. Refer to section 1.6: FCC Certified Antennas on page 9 for a list of certified antennas.
1.6 FCC Certified Antennas
This device has been designed to operate with the antennas listed below, having a
maximum peak gain of 24 dB. The Max. Tx Power Setting in the GUI listed below for
each antenna will limit the EIRP at any time to 1W/1MHz (30 dBm). Antennas not
included in this list or having a peak gain greater than 24 dB are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
Subscriber Station Antennas
Order Number DEG Gain (dBi) GHz Type Polarization
SU-O Integrated 30 16 3.3 - 3.8 162 x 162
Panel Vertical or
Horizontal
A2014ARF 13.8 20 3.3 - 3.8 336 x 336
Panel Vertical or
Horizontal
A2408MTF 8 24 3.3-3.8
600 x 600
Panel Vertical or Horizontal
A1815MTS 15 16.5 18.5
18
3.3-3.4
3.4-3.7
3.7-3.8
305 x 305
Panel Vertical or Horizontal

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 10 of 55
1.7 Frequency Selection
1.7.1 General
Operation in the FWA band is subject to license. The radio power and channel frequency
selections must be set correctly before the installed system is allowed to transmit. The
installed system must comply with all governing local, regional, and national regulations.
Contact authorities in the country of installation for complete information regarding the
licensing regime and operating restrictions for that regulatory domain.
1.7.2 R&TTE Directive 1999/5/EC Statements
Installation
The transceiver and antenna equipment must be installed by a qualified professional
installer and must be installed in compliance with regional, national, and local
regulations. It is the responsibility of the system installer and/or system operator to ensure
the installed system does not exceed any operational constraints identified by local
regulations. Refer to the sections in this product User Guide for detailed information about the
correct installation steps to ensure power and frequency settings are set correctly before
connecting the antenna. Operation in the 3.4-3.6 GHz band is subject to license. Authorities
within the country of installation can provide information regarding the licensing regime and
restrictions.
Community Language Declarations
The following table contains community language versions of informal statement in
accordance with Article 6.3 of Directive 1999/5/EC.
Table 1:R&TTE - Community Language CE Declarations
Community language versions of informal statement for inclusion in user
information in accordance with Article 6.3 of Directive 1999/5/EC
Danish Undertegnede Redline Communications erklærer herved, at følgende
udstyr subscriber overholder de væsentlige krav og øvrige relevante
krav i direktiv 1999/5/EF
Hierbij verklaart Redline Communications dat het toestel subscriber in
overeenstemming is met de essentiële eisen en de andere relevante
bepalingen van richtlijn 1999/5/EG
Dutch
Bij deze verklaart Redline Communications dat deze subscriber voldoet
aan de essentiële eisen en aan de overige relevante bepalingen van
Richtlijn 1999/5/EC.
English Hereby, Redline Communications, declares that this subscriber is in
compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.
Finnish Redline Communications vakuuttaa täten että subscriber tyyppinen laite
on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien
direktiivin muiden ehtojen mukainen.
Par la présente Redline Communications déclare que l'appareil
subscriber est conforme aux exigences essentielles et aux autres
dispositions pertinentes de la directive 1999/5/CE
French
Par la présente, Redline Communications déclare que ce subscriber est
conforme aux exigences essentielles et aux autres dispositions de la
directive 1999/5/CE qui lui sont applicables

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 11 of 55
Table 1:R&TTE - Community Language CE Declarations
Community language versions of informal statement for inclusion in user
information in accordance with Article 6.3 of Directive 1999/5/EC
Hiermit erklärt Redline Communications, dass sich dieser/diese/dieses
subscriber in Übereinstimmung mit den grundlegenden Anforderungen
und den anderen relevanten Vorschriften der Richtlinie 1999/5/EG
befindet". (BMWi)
German
Hiermit erklärt Redline Communications die Übereinstimmung des
Gerätes subscriber mit den grundlegenden Anforderungen und den
anderen relevanten Festlegungen der Richtlinie 1999/5/EG. (Wien)
Greek ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Redline Communications ∆ΗΛΩΝΕΙ ΟΤΙ subscriber
ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ
ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ
Italian Con la presente Redline Communications dichiara che questo
subscriber è conforme ai requisiti essenziali ed alle altre disposizioni
pertinenti stabilite dalla direttiva 1999/5/CE.
Portuguese Redline Communications declara que este subscriber está conforme
com os requisitos essenciais e outras provisões da Directiva 1999/5/CE.
Spanish Por medio de la presente Redline Communications declara que el
subscriber cumple con los requisitos esenciales y cualesquiera otras
disposiciones aplicables o exigibles de la Directiva 1999/5/CE
Swedish Härmed intygar Redline Communications att denna subscriber står I
överensstämmelse med de väsentliga egenskapskrav och övriga
relevanta bestämmelser som framgår av direktiv 1999/5/EG.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 12 of 55
Table 2:Notices - R&TTE: Countries of Use (3.4 GHz & 3.6 GHz)
Country 3400-3600
MHz Country 3400-3600 MHz Country 3400-3600 MHz
Austria 9Hungary 9Poland 9
Belgium 9Iceland 9Portugal 9
Bulgaria 9Ireland 9Romania 9
Cyprus Italy Slovakia
9
Czech
Republic
9Latvia 9Slovenia 9
Denmark 9Liechtenstein 9Spain 9
Estonia 9Lithuania 9Sweden 9
Finland 9Luxembourg 9Switzerland 9
France 9Malta 9United
Kingdom
9
Germany 9Netherlands 9
Greece 9Norway 9
R&TTE Directive 1999/5/EC - Declarations of conformity are available at the following
web site address:
http://www.redlinecommunications.com/conformance/
1.8 WEEE Product Return Process
Figure 1:Notices - WEEE Logo
In accordance with the WEEE (Waste from Electrical and Electronic Equipment)
directive, 2002/96/EC, Redline Communications equipment is marked with the logo
shown above. The WEEE directive seeks to increase recycling and re-use of electrical
and electronic equipment. This symbol indicates that this product should not be disposed
of as part of the local municipal waste program. Contact your local sales representative
for additional information.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 13 of 55
1.9 Important Service Information
1. Refer all repairs to qualified service personnel. Do not remove the covers or modify
any part of this device, as this voids the warranty.
2. Disconnect the power to this product and return it for service if the following
conditions apply:
a) The unit does not function after following the operating instructions
outlined in this manual.
b) Liquid has been spilled or a foreign object is inside.
c) The product has been dropped or the housing is damaged.
3. Record the serial number on your registration card for future reference.
4. Redline does not endorse or support the use of outdoor cable assemblies: i) not
supplied by Redline, ii) third-party products that do not meet Redline's cable and
connector assembly specifications, or iii) cables not installed and weatherproofed as
specified in the Installation Guidelines manual (70-00068-01-XX). Refer to the
Redline Limited Standard Warranty and RedCare service agreements.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 14 of 55
Chapter
2
2
2 O Ov ve er rv vi ie ew w
Congratulations on your purchase of the Redline WiMAX Forum Certified™ subscriber
wireless broadband product. Redline Communications is a world leader in design and
production of WiMAX and proprietary Broadband Fixed Wireless (BFW) systems.
The outdoor subscriber is carrier class high-speed IEEE 802.16-2004 WiMAX compliant
for point-to-point (PTP) and point-to-multipoint (PMP) deployment.
Figure 2: Intro - RedMAX Subscriber Outdoor System

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 15 of 55
2.1 Features
2.1.1 IEEE 802.16 WiMAX Compliance
The IEEE 802.16-2004 specifications describe a PMP broadband wireless access
standard for systems operating in the frequency range of 2-11 GHz, and 10-66 GHz. This
standard includes descriptions for both the Media Access Control (MAC) and the
physical (PHY) layers. Note that the 802.16-2004 standards are subject to amendment,
and the subscriber product design compliance applies to a specific revision of the
standard. The RedMAX product does not support mesh communication, but does support
subscriber-to-subscriber communication using TLS.
Redline is an active member of the WiMAX Forum™ and is participating in
interoperability testing in the WiMAX Forum. Redline is also an active member of the
IEEE 802.16-2004 standards committee and has been instrumental in creating the original
802.16-2004 standards, and is active in recommending, writing and following-up work on
new amendments to the 802.16-2004 specifications.
2.1.2 PHY Specification
The subscriber system is designed for 2-11 GHz operation based on the WirelessMAN-
OFDM PHY definition in the IEEE 802.16-2004 specifications. The subscriber uses
Orthogonal Frequency Division Multiplexing (OFDM). OFDM is a multi-carrier
transmission technique where the data stream is split and transmitted (at a reduced rate)
in parallel streams on separate sub-carriers. OFDM uses the Fast Fourier Transform
(FFT) algorithm to implement modulation and demodulation functions. Using adequate
channel coding and bit-interleaving, OFDM performs very well in severe multipath
environments, mitigates frequency-selective fading, and provides high spectral
efficiency.
2.1.3 Time Division Duplexing (TDD)
The subscriber system uses time division duplexing (TDD) to transmit and receive on the
same RF channel. The subscriber can also transmit and receive using separate RF
channels, referred to as half-duplex FDD (HD-FDD). These are both non-contention
based methods for providing an efficient and predictable two-way PTP or PMP cell
deployment. All uplink and downlink transmission scheduling is managed by the
WiMAX base station. The base station sends data traffic to subscribers, polls for grant
requests, and sends grant acknowledgements based on the total of all traffic to all
subscribers.
2.1.4 Coding Rate
Each burst of data transmitted over the air is padded with redundant information to make
it resistant to errors introduced during transmission. The coding rate is the ratio of user
data to the total data transmitted including the redundant error correction data. The
subscriber supports coding rates of 1/2, 2/3, and 3/4.
2.1.5 Modulation
The modulation technique specifies how the data is coded within the OFDM carriers. The
subscriber supports BPSK, QPSK, 16 QAM, and 64 QAM modulation.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 16 of 55
2.1.6 Reed Solomon Error Correction
Outer Reed-Solomon and inward Convolution Coding (RS-CC) error correction is
enabled for all traffic rates, with the exception of BPSK 1/2 where only inward
Convolution Coding is used. These low-level processes can correct bursts of errors in
received messages and reduce the number of retransmissions.
2.2 Deployment Models
The subscriber supports point to point (PTP) and point to multipoint (PMP) deployment
scenarios.
2.2.1 PTP Deployment
When deployed in a PTP configuration the base station establishes a dedicated bi-
directional link to a single subscriber. The PTP deployments typically use a directional
narrow beam antenna for both ends of the link.
Figure 3: System - PTP Line of Sight Deployment
2.2.2 PMP Deployment
When deployed in a PMP configuration the base station establishes bi-directional links to
more than one subscriber. The PMP deployments typically use a wide beam (sector)
antenna at the base station and a narrow beam antenna at the subscriber. Service flows are
used to police service level agreements for each subscriber.
2.2.3 Non Line-of-Sight
The subscriber system supports line-of-sight (LOS), optical line-of-sight (OLOS), and
non line-of-sight (NLOS) operation. A clear LOS link has no obstacles within 60% of the
first Fresnel zone of the direct path. An OLOS link has obstructions within 60% of the
first Fresnel zone, but a visible path exists from the base station to the subscriber.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 17 of 55
Figure 4: System - Fresnel Zone
A wireless link is considered non LOS if natural or man-made structures block the visible
path between the base station and subscriber. In this case, a wireless link can be
established only if a reflective path can be established between the base station and
subscriber.
Figure 5: System - Non-Line of Sight Deployment
2.2.4 Channelization
The subscriber is a frequency-specific system, with the frequency band defined by the
internal transceiver unit. The use of the operating band must be in accordance with
European Conference of Postal and Telecommunications Administrations (CEPT)
Recommendation 14-03.
The subscriber divides the available frequency band into channels. Allocation of channels
during deployment is dependent on spectrum availability in the licensed FWA band
(3400-3600 MHz) and local licensing requirements and conditions. Channel selection

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 18 of 55
allows planners to obtain the maximum geographic coverage, while avoiding frequency
contention in adjacent sectors.
2.3 Service Flows
Service flows are a key feature of the 802.16 standard. A Service Flow represents a
unidirectional data flow having separate QoS settings for uplink and downlink. Service
flows provide the ability to set up multiple connections to each subscriber in a sector.
Separate service flows can be established for uplink and downlink traffic, where each
service flow is assigned a unique service level category and separate QoS settings. This
feature allows segregation of high-speed/high-priority traffic from less time-critical
flows.
2.3.1 Service Flow Classification
Data packets are forwarded by the subscriber based on classification rules. Classification
rules require examining each packet for pattern matches such as destination address,
source address, or VLAN tag. All classification is defined at the base station and the
classification parameters are downloaded to the subscriber.
RedMAX supports service flows with different classification types including: 802.3
Ethernet, 802.1Q VLAN, IPV4, IPV4 Over 802.3 and IPV4 Over 802.1Q -- with options
to classify based on Source and Dest of MAC and IP addresses, VLAN tag and Vlan
priority, Src and Dst port number, TOS Value and Ethernet protocol type.
2.3.2 Dynamic Service Addition
Service flows are defined and stored in the base station. For each service flow to be
established, the base station sends a setup message to the subscriber specifying the
required set of QoS parameters. The subscriber responds to each request by accepting or
rejecting the setup message.
A service flow may be pre-provisioned or can be dynamically created and deleted
without service outage. This is useful for supporting multiple subscribers in a single
sector. New subscribers can be added and existing subscribers can be removed or have
service levels modified.
Setup messages are sent by the base station following any subscriber power-cycle, loss
and recovery of the wireless link to a subscriber, or any service flow add/delete operation
at the base station.
2.3.3 Uplink Service Flow Scheduling
The base station enforces QoS settings for each service flow by controlling all uplink and
downlink traffic scheduling. This provides non-contention based traffic model with
predictable transmission characteristics. By analyzing the aggregate requests of all
subscribers, the base station ensures that uplink and downlink traffic conforms with the
current service level agreements (SLAs). Centralized scheduling increases traffic
predictability, eliminates contention, and provides maximum opportunity for reducing
overhead.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 19 of 55
Real-Time Polling Service (rt-PS)
The base station schedules a continuous regular series of transmit opportunities for the
subscriber to send variable size data packets. The grant size is based on the current data
transfer requirement. Typical applications include streaming MPEG video or VOIP with
silence suppression. This is efficient for applications that have a real-time component and
continuously changing bandwidth requirements.
Non-Real-Time Polling Service (nrt-PS)
The base station schedules regular transmit opportunities for the subscriber to send
variable size data packets. Typical applications may include high bandwidth FTP. The
polling period may typically be one second or less, even during periods of network
congestion.
Best Effort (BE)
The base station schedules transmit opportunities for the subscriber to send traffic based
on unused bandwidth after all higher level traffic scheduling requirements are serviced.
Typical applications may include Internet access and email. Best effort service flows can
be assigned a priority of 0 to 7.
Unsolicited Grant Service (UGS)
The base station schedules a continuous series of transmit opportunities for the subscriber
to send fixed size data packets. This schedule supports real-time applications including
VoIP or TDM transport. The UGS pre-scheduled grants guarantee reserved bandwidth
and reduce latency introduced by repetitive grant requests. The service flow will not
transmit packets larger than nominal grant interval.
2.3.4 Downlink Service Flow Scheduling
The base station schedules downlink traffic on active service flows based on the
minimum reserved data rate (CIR), traffic priority, and maximum latency.

RedMAX™Subscriber Modem
SU-O User Manual
70-00057-01-01-DRAFT Proprietary Redline Communications © 2007 September 7, 2007
Page 20 of 55
Chapter
3
3
3 O Ou ut td do oo or r S Su ub bs sc cr ri ib be er r F Fe ea at tu ur re es s
The RedMAX subscriber can be deployed with an integrated antenna or an external
antenna.
3.1 Integrated Antenna (SU-OIA)
This subscriber with integrated antenna consists of an outdoor radio (transceiver and
antenna) and an indoor power-block with network connections. The subscriber
electronics are housed in a weatherproof aluminum alloy case.
Figure 6: SU-OIA System Features
The SU-OIA system includes:
- Outdoor subscriber with integrated antenna
- Universal mounting bracket
Optional SU-OIA equipment includes:
- Outdoor Ethernet cable with weatherproof connector
- Indoor Power over Ethernet (PoE) power adaptor with AC power cord (NA/UK/EU)
- Lightning/surge protection