Redline Sports M01480RW User manual
1
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
1-888-996-2729
FAX: 1-866-873-3535
gameroom@escaladesports.com
We strive to ensure that our products are of the highest quality
and free of manufacturing defects or missing parts. However, if
you have any problems with your new product,
DO NOT RETURN IT TO THE STORE,
please contact us toll free @:
Or write to:
Escalade Sports
Customer Service Department
P.O. Box 889
Evansville IN 47706
When contacting Escalade Sports please provide your model number, date code (if
applicable), and part number if requesting a replacement part. These numbers are
located on the product, packaging, and in this owners manual.
Your Model Number:
Please have your model number when inquiring about parts.
M01480RW
Date Code:
2-M01480RW- -ZG
All Rights Reserved
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT! READ EACH STEP
IN THIS MANUAL BEFORE YOU
BEGIN THE ASSEMBLY.
TWO (2) ADULTS ARE REQUIRED TO ASSEMBLE
THIS BASKETBALL SHOOTOUT
READ AND FOLLOW ALL ASSEMBLY, OPERATION, AND
SAFETY INSTRUCTIONS CAREFULLY. AT LEAST TWO
ADULTS ARE NEEDED TO PUT THIS BASKETBALL
SHOOTOUT TOGETHER.
2
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved
Tools Needed:
Wrenches T1 and T2 (Included with the Hardware Kit)
Philips Screwdriver
Adjustable Wrench or Socket Set is helpful but not required.
Make sure you understand the following tips before you begin to assemble your
basketball shootout.
1.This game ( Mechanical Scoring ) can be played outdoors - but must be stored
indoors.
2.Tighten hardware as instructed.
3.Do not over tighten hardware,as you could crush the tubing.
4.Some drawings or images in this manual may not look exactly like your product.
5.To prevent damage to the electronics, do not place this unit any closer than six inches
from the wall.
!
H1 - M6 x 25mm
Allen Head Bolt (8)
H4 - M6 x 45mm
Allen Head Bolt (4)
H5 - M6 Flat
Washer (44)
H6 - M6 Locknut (20)
H2 - M6 x 55mm
Allen Head Bolt (2)
H3 - M6 x 35mm
Allen Head Bolt (8)
3
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved
T1 - Allen Wrench (1) T2 - Wrench (1)
(Not to Scale) (Not to Scale)
HARDWARE IDENTIFIER
(To Scale)
P1 - Top Tube (2) P2 - Top Back Upright (2)
P3 - 27.5” Middle Back Upright (2) P4 - Lower Back Upright (2)
4For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All RIghts Reserved.
PARTS IDENTIFIER (Not to Scale)
P5 - 24.5” Back Top Support Tube (1) P6 - 31” Front Support Tube (2)
P7 - Front Upright (2) P8L - Left Connect Tube (1)
P8R - Right Connect Tube (1)
P9 - 26.25” Base Tube Upright (2) P10 - Front Leg Tube (2)
P11 - 17.75” Front Tube (1) P12 - Front Cross Tube (1)
P13 - Front Support Brace (1) P14 - Curved Side Brace (2)
P15 - Back Bottom Support Tube (1) P15R - Back Top Support Ramp Tube (1)
2
2013
6
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
P16
PARTS REQUIRED:
1 pc - P16 Backboard
1 pc - P20 Electronic Scoreboard
3 pcs - AA Batteries (not included)
1. Locate four(4) pieces Phillips Head Screws, P20 Electronic Scoreboard from the box.
2. Peel protective coating from P20 Electronic Scoreboard as shown in FIGURE 1.
Note inset, back view. Install 3 "AA" batteries into electronic scorer.
3. Attach P20 Electronic Scoreboard to P16 Backboard using four pieces Phillips Head Screws as
shown in FIGURE 1.
FIGURE 1
P20
Phillips Head Screw
NOTE:
Peel protective
coating.
7
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
H6
H1
H5
T1
P21
T2
NOTE:
Scoring Arm plug
through the hole
on the backboard.
H5
Place Net P18
on Rim P17
NOTE:
Net has a special slot
in it to allow mechanical
scoring arm to move up
and down and score
properly.
Install net "special slot”
onto rim in correct position
thus allowing the mechanical
scoring arm to move up and
down correctly.
P18
P17
FIGURE 2
T1
H1
H5
P17
H5
H6
T2
P19
P16
P16
PARTS REQUIRED:
8 pcs - H1 Allen Head Bolt 1 pc - P18 Rim Net 1 pc - T1 Allen Wrench
16 pcs - H5 Flat Washer 1 pc - P19 Rim Support Plate 1 pc - T2 Wrench
8 pcs - H6 Lock Nut 1 pc - P21 Mechanical Scoring
1 pc - P17 Rim Arm
4. Attach P17 Rim to P16 Backboard using H1 Bolts, H5 Flat Washers, P19 Rim Support Plate and
H6 Lock Nuts as shown in FIGURE 2. P19 Rim Support Plate attaches to the back of backboard
as per diagram. Use T1 Allen Wrench and T2 Wrench to tighten H1 Bolts and H6 Lock Nuts.
5. Attach P21 Mechanical Scoring Arm to P16 Backboard using H1 Bolts, H5 Flat Washers and
H6 Lock Nuts as shown in FIGURE 3. Use T1 Allen Wrench and T2 Wrench to tighten H1 Bolts
and H6 Lock Nuts.
Connect P21 Scoring Arm plug to the back side of P20 Electronic Scoreboard as shown.
6. Place P18 Net on P17 Rim as shown in FIGURE 4.
FIGURE 3
FIGURE 4
Scoring Arm
Plug
Backside
of Electronic
Scoreboard
On / Off Switch is
located under the
electronic
scoreboard
8
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
P1
P1
P2
P2
P5
P24
P23
P25
P23
PARTS REQUIRED:
2 pcs - P1 Top Tube 2 pcs - P23 L-Joint Plastic Part
2 pcs - P2 Top Back Upright 1 pc - P24 Left 4-Joint Plastic Part
1 pc - P5 24.5” Back Top 1 pc - P25 Right 4-Joint Plastic Part
Support Tube
7. Snap P1 Top Tubes to P23 L-Joint Plastic Parts using spring locks as shown in FIGURE 5.
8. Snap P2 Top Back Upright Tubes to P23 L-Joint Plastic Parts using spring locks as shown in
FIGURE 5.
9. Snap P24 Left and P25 Right 4-Joint Plastic Part to P2 Tube using spring locks as shown in
FIGURE 5.
10. Snap P5 Back Top Support Tube between P24 Left and P25 Right 4-Joint Plastic Part using
spring locks as shown in FIGURE 5.
FIGURE 5
NOTE:
Make sure P24's and P25's
are in this position for correct
assembly .
9
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
PARTS REQUIRED:
2 pcs - P3 27.5” Middle Back Upright 2 pcs - P6 31” Front Support Tube
2 pcs - P4 Lower Back Upright 2 pcs - P7 Front Upright
11. Snap P3 Middle Back Upright Tubes & P6 Front Support Tubes to P24 Left and P25 Right 4-Joint
Plastic Part using spring locks as shown in FIGURE 6 .
12. Snap P4 Lower Back Upright Tubes to P3 Middle Back Upright Tubes using spring locks as
shown in FIGURE 6.
13. Snap P7 Front Upright Tubes to P6 Front Support Tubes using spring locks as shown in
FIGURE 6.
FIGURE 6
P24
P25
P3
P4
P6
P7
P6
P7
P3
P4
NOTE:
Swedge must be
in this position for
correct assembly.
NOTE:
Swedge must be
in this position for
correct assembly.
10
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
PARTS REQUIRED:
6 pcs - H3 Allen Head Bolt 2 pcs - P14 Curved Side Brace
10 pcs - H5 Flat Washer 1 pc - P15 Back Bottom Support Tube
4 pcs - H6 Lock Nut 1 pc - T1 Allen Wrench
1 pc - P13 Front Support Brace 1 pc - T2 Wrench
14. Install P13 Front Support Brace and P14 Curved Side Braces to P7 Tubes using H3 Allen Head
Bolts with H5 Flat Washers as shown in FIGURE 7. Do not tighten Bolts.
15. Install P15 Back Bottom Support Tube and another end of P14 Curved Side Braces to P4 Tubes
using H3 Allen Head Bolts, H5 Flat Washers and H6 Lock Nuts as shown in FIGURE 7.
Tighten all Bolts and Nuts.
FIGURE 7
H3
H5
H5
H6
H3
H5
P13
P14
P14
P15
P7
P4
P4
P7
NOTE:
Be sure to attach P14
onto bottom hole as
shown.
NOTE:
Be sure to attach P14
onto bottom hole as
shown.
11
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
PARTS REQUIRED:
2 pcs - H2 Allen Head Bolt 2 pcs - P9 26.25” Base Tube Upright
6 pcs - H5 Flat Washer 2 pcs - P10 Front Leg Tube
2 pcs - H6 Lock Nut 2 pcs - P23 L-Joint Plastic Part
1 pc - P8L Left Connect Tube 1 pc - T1 Allen Wrench
1 pc - P8R Right Connect Tube 1 pc - T2 Wrench
16. Install P8L (Left) and P8R (Right) Connect Tubes to P7 Tubes using H2 Allen Head Bolts, H5
Flat Washers and H6 Lock Nuts as shown in FIGURE 8.
Note: This is a pivot point. “Snug” tighten H6 Lock Nuts only. Make sure this assembly
pivots freely.
17. Snap P9Base Tube Uprights to P8L and P8R Connect Tubes using spring locks as shown in
FIGURE 8.
18. Snap P23 L-Joint Plastic Parts to P9 Base Tubes using spring locks as shown in FIGURE 8.
19.Snap P10 Front Leg Tubes to P23 L-Joint Plastic Parts using spring locks as shown in FIGURE 8.
FIGURE 8
P10
P10
P23
P9
P9
P8L
(Left)
P8R (Right)
H2
H5
H5
H6
H5
H2
P7
P7
NOTE:
Be sure to attach P8L
onto bottom hole as
shown.
NOTE:
Be sure to attach P8R
onto bottom hole as shown.
NOTE:
Swedge must be
in this position for
correct assembly
NOTE:
Swedge must be
in this position for
correct assembly
12 For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
t
PARTS REQUIRED:
4 pcs - H4 Allen Head Bolt 1 pc - P15R Back Top Support 1 pc - T1 Allen Wrench
8 pcs - H5 Flat Washer Ramp Tube 1 pc - T2 Wrench
4 pcs - H6 Lock Nut 1 pc - P22 Ramp Net
1 pc - P11 17.75” Front Tube 2 pcs - P23 L-Joint Plastic Part
20. Slide P22 Ramp Net into P1 Top Tube as shown in FIGURE 10.
21. Attach Backboard assembly to the frame. With the help of another adult, start at top hole, place
a H5 Flat Washer on a H4 Bolt, pass the bolt through P2 Tube and P16 Backboard, place H5
Flat Washer on the bolt and secure with a H6 Lock Nut as shown in FIGURE 10. Repeat for other
side. Do not tighten Bolts.
At each bottom hole of the backboard, repeat the above procedure except bring the ramp up
behind the P5 Tube, slide P15R Tube through sleeve on the back of P22 Ramp Net and attach
with H5 Washer and H6 Lock Nut as shown in FIGURE 10. Tighten all Bolts & Nuts using T1 Allen
Wrench and T2 Wrench.
22. Snap P23 L-Joint Plastic Parts to P11 Front Tube using spring locks as shown in FIGURE 11.
FIGURE 11
FIGURE 10
P11
P23
P23
H5
H6
H5 H4
H5
H6
H5
H6
H5
H6
H5 H4
P16
P2
Note:
Place P22 Ramp Net
behind P5 Tube.
P5
P22
P15R
P22
P1
P22
P1
Note:
Make sure flat surface face
toward P16 Backboard for
correct assembly.
13
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
PARTS REQUIRED:
2 pcs - H3 Allen Head Bolt 1 pc - P12 Front Cross Tube
4 pcs - H5 Flat Washer 1 pc - T1 Allen Wrench
2 pcs - H6 Lock Nut 1 pc - T2 Wrench
23. Slide P23 L-Joint Plastic Parts and P11 Tube assemble from STEP 22 onto P10 Tubes as shown.
Slide P12 Front Cross Tube through sleeve on the front of the ramp net, attach P12 Tube to
P23 L-Joint Plastic Parts and P10 Tube assemble using H3 Allen Head Bolts, H5 Flat Washers
and H6 Lock Nuts as shown in DETAIL A.
Tighten Bolts and Nuts with T1 Allen Wrench and T2 Wrench.
24. Secure the Velcro Straps (front of the ramp net) around the P23 L-Joint Plastic Part as shown
in FIGURE 12.
FIGURE 12
DETAIL A
H5
H3
H5
H6
P12
P22
P10
P23
14
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
FIGURE 13
In STORAGE position,
use P26 Locking Pin to lock
ramp in storage position.
P26 Locking Pin
15
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
Inset 3(three) pieces “AA” batteries at the backside of electronic scoreboard.
Plug the mechanical scoring arm plug into backside of the electronic scoreboard.
Press on/off button at the bottom backside of the electronic scoreboard to play and stop the game.
Each player has 60 seconds to make as many baskets as they can. During the first 45 seconds
each shot counts as 2 points. During the last 15 seconds each shot counts as 3 points.
USE OF YOUR SHOOTOUT
CARE AND USE OF YOUR SHOOTOUT
Congratulations! You have now assembled your Single Shootout.
Please note the Care and Use instructions below.
1. Product can be used OUTDOORS - but must be stored INDOORS.
2. DO NOT sit, climb or lean on the unit.
3. DO NOT drag the unit when moving it, This will damage the legs.
2
01480RWZGH1
01480RWZGH2
01480RWZGH3
01480RWZGH4
01480RWZGH5
01480RWZGH6
01480RWZGT1
01480RWZGT2
01480RWZGP1
01480RWZGP2
01480RWZGP3
01480RWZGP4
01480RWZGP5
01480RWZGP6
01480RWZGP7
01480RWZGP8L
01480RWZGP8R
01480RWZGP9
01480RWZGP10
01480RWZGP11
01480RWZGP12
01480RWZGP13
01480RWZGP14
01480RWZGP15
01480RWZGP15R
01480RWZGP16
01480RWZGP17
01480RWZGP18
01480RWZGP19
01480RWZGP20
01480RWZGP21
01480RWZGP22
01480RWZGP23
01480RWZGP24
01480RWZGP25
01480RWZGP26
01480RWZGA1
01480RWZGA2
01480RWZGK1
01480RWZGM1
- M01480RW -
2013
17
For Customer Service Call 1-888-996-2729
© 2013 Escalade Sports
All Rights Reserved.
This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS
Product (hereinafter referred as the "Product").
WARRANTY DURATION: This Product is warranted to the original consumer purchase of a pe-
riod of 90 days from the original purchase.
WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser
that any Product of its manufacture is free from defects in material and workmanship when used
for the intended purpose under normal use and conditions. THIS WARRANTY IS VOID IF THE
PRODUCT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE, NEGLIGENCE,
IMPROPER SERVICE, FAILURE TO FOLLOW INSTRUCTIONS PROVIDED WITH THE PROD-
UCT OR OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL AND WORKMAN-
SHIP.
WARRANTY PERFORMANCE: During the above 90 day warranty period, ESCALADESPORTS
shall repair or replace with a comparable model, and Product, or component thereof, which may
prove defective under normal use and proper care, and which our examination shall disclose to
our satisfaction to be thus defective, please contact our Warranty Dept.
1-888-996-2729 / Warranty Dept.
Or Write us at:
Escalade® Sports, Inc. - P.O. Box 889, Evansville, IN 47706
Attn: Warranty Dept.
Or E-mail us at:
Other than shipping requirements no charge will be made for such repair or replacement of in-
warranty Products. ESCALADE SPORTS strongly recommends that the Product is insured for
value prior to mailing.
WARRANTY DISCLAIMERS: ANY IMPLIED WARRANTIES ARISING OUT OF
THIS SALE, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIM-
ITED IN DURATION TO THE ABOVE 90 DAY PERIOD. ESCALADE SPORTS
SHALL NOT BE LIABLE FOR LOSS OF USE OF THE PRODUCT OR OTHER
CONSEQUENTIAL OR INCIDENTAL COSTS, EXPENSES OR DAMAGES IN-
CURRED BY THE CONSUMER OF ANY OTHER USE.
Some states do not allow the exclusion or limitation of implied warranties or consequential or
incidental damages, so the above limitations or exclusions may not apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights and you may also have other
rights which may vary from state to state.
90 DAY LIMITED WARRANTY
Table of contents
