Redline RDL-3000 SC Instruction sheet

Virtual Fiber™
Outdoor Wireless TCP/IP Transport
70-00159-02-00 Proprietary Redline Communications © 2014 Page 1of 59 July 18, 2014
RDL-3000
Universal Wireless Transport™
(UWT™) System
Ellipse TMA Sector Controller
Multi-Sector System
Installation Guidelines
1Important Notices...................................................................8
2System Features...................................................................14
3Materials................................................................................33
4Site Survey............................................................................34
5Site Preparation....................................................................39
6Assemble Kits.......................................................................42
7Install Equipment..................................................................46
8Reference..............................................................................53

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 2of 59 July 18, 2014
Copyright Information
All rights reserved July 18, 2014. The information in this document is proprietary to
Redline Communications Inc. This document may not in whole or in part be copied,
reproduced, or reduced to any medium without prior consent, in writing, from Redline
Communications Incorporated.
Contact Information:
Redline Communications Inc.
302 Town Centre Blvd.
Markham, ON
Canada L3R 0E8
Web site:
www.rdlcom.com
Email:Inquiries: [e-mail]
Support: [e-mail]
Training: [e-mail]
Document Control:
70-00159-02-00-RDL-3000_Ellipse_TMA_SC_Installation_Guide-20140718a.doc
Disclaimer
The statements, configurations, technical data, and recommendations in this document
are believed to be accurate and reliable, but are presented without express or implied
warranty. Additionally, Redline makes no representations or warranties, either expressed
or implied, regarding the contents of this product. Redline Communications shall not be
liable for any misuse regarding this product. The information in this document is subject
to change without notice. No part of this document shall be deemed to be part of any
warranty or contract unless specifically referenced to be part of such warranty or
contract within this document.
Software Versions
This manual describes operation using software release v2.27 and may include features
that are different or unavailable in previous software releases.
Some Ellipse TMA Sector Controller features are controlled by options keys and are
available only on specific revisions of hardware systems. Refer to the individual product
Release Notes for information about required software and availability of features.

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 3of 59 July 18, 2014
Revision Log
Date
Item
Description of Changes
20140626
All
First draft

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 4of 59 July 18, 2014
TABLE OF CONTENTS
1Important Notices...................................................................8
1.1 Important Deployment Information...................................................................8
1.2 Service & Safety.................................................................................................8
Safety Warnings.............................................................................................8
General Warnings..........................................................................................8
Warning Symbols...........................................................................................8
1.3 Installation Safety..............................................................................................9
Professional Installation / Installations Professionnel .....................................9
Safety Precautions.........................................................................................9
Electrocution Hazard / Risque D’électrocution................................................9
Radio Frequency Safety / Sécurité des Fréquences Radio ..........................10
Personal Safety............................................................................................10
Electrical Safety ...........................................................................................10
Electrical Safety Compliance / Conformité à la Sécurité Electrique ..............10
UL Information .............................................................................................11
Lightning Protection / Protection Contre la Foudre.......................................11
1.4 WEEE Product Return Process.......................................................................12
1.5 Service & Warranty Information......................................................................13
2System Features...................................................................14
2.1 Ellipse TMA Sector Controller.........................................................................18
Ethernet/Power Port.....................................................................................18
TMA-SYNC Port...........................................................................................18
GPS Antenna Port........................................................................................19
Ground Lug..................................................................................................19
RF Ports.......................................................................................................19
2.2 TMA Tower Amplifier.......................................................................................20
RF In Ports...................................................................................................20
TMA-SYNC Port...........................................................................................20
Power Port...................................................................................................21
Ground Lug..................................................................................................21
RF Out Ports................................................................................................21
2.3 Sector Antenna ................................................................................................22
2.4 Antenna RF Cables..........................................................................................24
2.5 Antenna RF Jumper Cables ............................................................................24
2.6 Ethernet Cables (Circular Connector) ............................................................25
2.7 PoE Power Injector ..........................................................................................26
2.8 RF Splitter.........................................................................................................28
2.9 Synchronization Kit .........................................................................................31
2.10 GPS Antenna Kit..............................................................................................32

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 5of 59 July 18, 2014
3Materials................................................................................33
4Site Survey............................................................................34
4.1 General Layout Options ..................................................................................34
4.2 Survey for RF Access to Sector Antennas.....................................................35
4.3 Survey for GPS Satellites................................................................................36
4.4 Survey Power Source......................................................................................37
4.5 Survey Network (Ethernet) Connection..........................................................38
5Site Preparation....................................................................39
5.1 Mast for Ellipse TMA Sector Controller..........................................................39
5.2 Mast for Sector Antenna..................................................................................40
5.3 Mast for GPS Antenna.....................................................................................41
6Assemble Kits.......................................................................42
6.1 Assemble Sector Controller with RF Splitter.................................................42
6.2 Assemble Sector Antenna with TMA Amplifier..............................................44
Wiring the TMA Tower Amplifier Detail View................................................45
7Install Equipment..................................................................46
7.1 Mount Sector Antenna on Mast ......................................................................47
Mounting Detail View ...................................................................................48
7.2 Tower Cabling..................................................................................................49
7.3 Mount GPS Antenna System...........................................................................50
7.4 Assemble GPS Antenna Kit.............................................................................50
7.5 Mount Sector Controller (with RF Splitter).....................................................51
7.6 Sector Controller Wiring Overview.................................................................52
8Reference..............................................................................53
8.1 Weatherproofing Procedures..........................................................................53
8.2 General Grounding Guidelines.......................................................................55
8.2.1 Grounding.......................................................................................................55
8.2.2 Surge Protection.............................................................................................56
8.2.3 Air Terminal Mounting for Tower and Pole Deployments.................................57
8.2.4 Protecting Cables from Abrasion and Temperature.........................................57
LIST OF TABLES
Table 1: Notice - Electrical Safety Specifications...........................................................11
Table 2: Avis - Spécifications de sécurité électrique......................................................11
Table 3: Features- Ellipse TMA Sector Controller System Components........................17
Table 4: Features - PoE Power Injector Ports................................................................22

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 6of 59 July 18, 2014
Table 5: Features - PoE Power Injector Ports................................................................26
Table 6: Materials - Installer Supplied Materials ............................................................33
Table 7: Survey: Power Cable.......................................................................................37
LIST OF FIGURES
Figure 1: Notice - WEEE Logo.......................................................................................12
Figure 2: Features: Ellipse TMA Sector Controller System Overview ............................14
Figure 3: Features: Ellipse TMA Sector Controller Simplified Block Diagram.................15
Figure 4: Features: Ellipse TMA Sector Controller System Components.......................16
Figure 5: Features: - Ellipse TMA Ports.........................................................................18
Figure 6: Features: Ellipse TMA RF Ports (Top View of Radio) .....................................19
Figure 7: Features: Ellipse TMA Sector Controller Dimensions .....................................19
Figure 8: Features: TMA RF Tower Amplifier RF IN, Sync and Power In.......................20
Figure 9: Features: TMA RF Tower Amplifier RF IN, Sync and Power In.......................20
Figure 10: Features: Ellipse TMA RF Ports (Top View of Radio) ...................................21
Figure 11: Features: Ellipse TMA Power Amplifier Dimensions.....................................21
Figure 12: Features: UHF Sector Antenna Ports ...........................................................22
Figure 13: Features: Sector Antenna Dimensions .........................................................23
Figure 14: Features: RF Antenna Cables - SC Splitter to Tower Amp ...........................24
Figure 15: Features: RF Jumper Cables - Antenna to TMA Tower Amplifier..................24
Figure 16: Features: Ethernet Data Cable.....................................................................25
Figure 17: Features - Ethernet PoE - Indoor Power Module Pinout ...............................26
Figure 18: Features: PoE Power Injector Mounting Dimensions....................................27
Figure 19: Features: RF Splitter-Combiner....................................................................28
Figure 20: Features: RF Splitter Dimensions.................................................................28
Figure 21: Features: Wireless Terminal/Splitter Mounting Bracket Dimensions.............29
Figure 22: Features - Ethernet Line Protection Ports.....................................................30
Figure 23: Features - Ethernet Line Protection Device Dimensions...............................30
Figure 24: Features: Synchronization Kit.......................................................................31
Figure 25: Features: Synchronization Kit with Terminator..............................................31
Figure 26: Features: GPS Antenna Kit...........................................................................32
Figure 27: Survey: Ellipse TMA Sector Controller General Layout.................................34
Figure 28: Survey: UHF Antenna...................................................................................35
Figure 29: Survey: GPS Antenna...................................................................................36
Figure 30: Survey: Power Cable Routing.......................................................................37
Figure 31: Survey: Ethernet Cable Routing ...................................................................38
Figure 32: Preparation - Ellipse TMA Sector Controller Mast Requirements..................39
Figure 33: Preparation - Sector Antenna with TMA Amplifier Mast Requirements .........40
Figure 34: Preparation - GPS Antenna Mast Requirements...........................................41
Figure 35: Assembly- Sector Controller with RF Splitter................................................42
Figure 36: Assembly - Mounting the Ellipse TMA Base Station (with splitters)...............43
Figure 37: Assembly: Mounting Tower Amplifier to the Sector Antenna.........................44
Figure 38: Assembly: Tower Amplifier Wiring ................................................................45
Figure 39: Sector Controller: Dual Polarity UHF Panel Antenna: Mounting Detail..........45
Figure 40: Installation TMA Sector Controller General Layout .......................................46
Figure 41: Installation: Mounting the Sector Antenna.....................................................47
Figure 42: Installation: Mounting the Sector Antenna.....................................................48

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 7of 59 July 18, 2014
Figure 43: Installation: Sector Antenna / Amplifier Wiring ..............................................49
Figure 44: Assembly: - GPS Antenna Kit.......................................................................50
Figure 45: Installation: Mounting Sector Controller and Splitter .....................................51
Figure 46: Installation: Ellipse TMA Sector Controller Wiring Overview .........................52
Figure 47: Procedures - RF Port - Weatherproofing Pt-1...............................................53
Figure 48: Procedures - RF Port - Weatherproofing Pt-2...............................................54
Figure 49: Procedures - RF Port - Weatherproofing Pt-3...............................................54
Figure 50: Procedures - RF Port - Weatherproofing Pt-4...............................................54
Figure 51: Procedures - Installing Surge Protection.......................................................56
Figure 52: Procedures - Air Terminal for Tower and Pole Deployments.........................57
Figure 53: Procedures - Cable Protection - Spiroband...................................................57

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 8of 59 July 18, 2014
1 Important Notices
1.1 Important Deployment Information
IMPORTANT: Refer to the RDL-3000 Family User Manual for detailed regulatory
information. Refer to this document before deploying and powering RDL-3000 family
systems in the field.
1.2 Service & Safety
Safety Warnings
WARNING - MICROWAVE TRANSMISSIONS: Do not operate or work in close
proximity to this equipment without first having proper training or knowledge of
microwave radio operation.
Read this manual and follow all operating and safety instructions.
Installation of the system must be contracted to a professional installer.
Keep all product information for future reference.
The power requirements are indicated on the product-marking label. Do not exceed
the described limits.
The unit must not be located near power lines or other electrical power circuits.
Disconnect the power before cleaning, or when the unit is not be in-use for an
extended period.
The system must be properly grounded to protect against power surges and
accumulated static electricity. The user is responsible for installing this device in
accordance with the local electrical codes: correct installation procedures for
grounding the unit, mast, lead-in wire and discharge unit, location of discharge unit,
size of grounding conductors and connection requirements for grounding electrodes.
General Warnings
Redline recommendations for maximum safety include the following:
Do not operate microwave equipment without first having proper training or
knowledge of microwave radio operation.
Do not operate the microwave equipment without an appropriate antenna port
termination, or antenna.
Do not look into or stand in front of an antenna.
Do not swing or aim an antenna at nearby persons while the equipment is operating.
Check to ensure that the area around the antenna is clear of personnel prior to
turning the transmitter on.
In locations where other antennas are installed, do not proceed with an installation
without first determining the RF/µW exposure risk. Where necessary have the
relevant transmitters turned off or wear a protective suit for the duration of the
installation.
Warning Symbols
These symbols may be encountered during installation or troubleshooting. These
warning symbols mean danger. Bodily injury may result if you are not aware of the safety
hazards involved in working with electrical equipment and radio transmitters. Familiarize
yourself with standard safety practices before continuing.
Chapter 1

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 9of 59 July 18, 2014
WARNING
ELECTRO-MAGNETIC
RADIATION
WARNING
HIGH VOLTAGE
WARNING
HOT SURFACE
DO NOT TOUCH
1.3 Installation Safety
Professional Installation / Installations Professionnel
Redline RDL-3000 systems require professional installation. The user is responsible to
ensure all building and safety codes are met and the installation is complete and
secure.
The RDL-3000 system shall be installed according to local Electrical Safety Codes.
For Canadian installations, the entire equipment installation must comply with the
Canadian Electrical Code. For installations in the United States, the entire equipment
installation must be in accordance with Article 810 of the United States National
Electrical Code.
Les appareils RDL-3000 de Redline doivent être installés par un personnel
professionnel. Le personnel responsable doit s’assurer que l’installation est bien
achevée, et qu’elle répond aux exigences de tous les codes de sécurité.
Le RDL-3000 doit être installé conformément aux codes locaux de sécurité électrique.
Pour les installations Canadiennes, l'installation de l'équipement au complet doit se
conformer au Code Canadien de l'électricité. Pour les installations aux États-Unis,
l'installation de l'équipement au complet doit être en conformité avec l'article 810 du
Code des États-Unis National Electrical.
Safety Precautions
Installation and service must be done by personnel having technical training and
experience necessary to be aware of hazards during installation and/or service of
outdoors RF equipment. The installation and/or service must be done using procedures
designed to minimize any danger to technical personnel or any other person.
Use safety devices when working on or around the mast. Be aware of the risk of falling
objects. Use provided safety catches when hoisting antennas and radios.
Do not use any components (screws, nuts, etc.) other than those delivered together with
the Redline microwave radio equipment or those recommended by Redline.
Electrocution Hazard / Risque D’électrocution
Warning to Service Personnel
Do not install Redline products near any type of power line. Should the antenna or
related hardware come in contact with power lines, severe bodily harm or death could
result!

RDL-3000 Ellipse TMA Sector Controller Installation Guidelines
70-00159-02-00 Proprietary Redline Communications © 2014 Page 10 of 59 July 18, 2014
Attention au personnel du service
Ne pas installer les produits Redline près n'importe quel type de ligne électrique. Si votre
antenne ou du matériel connexe entrer en contact avec des lignes électriques, des
blessures graves ou la mort pourraient en résulter!
Radio Frequency Safety / Sécurité des Fréquences Radio
The installer of this radio equipment must ensure that the antenna is located or pointed
such that the antenna does not emit RF fields in excess of the general population limits
as defined by:
FCC CFR 47, Part 2.1091
http://www.gpo.gov/fdsys/pkg/CFR-2009-title47-vol1/pdf/CFR-2009-title47-vol1-sec2-
1091.pdf
FCC OET Bulletin 65, Radio frequency radiation exposure evaluation for fixed
devices
http://transition.fcc.gov/Bureaus/Engineering_Technology/Documents/bulletins/oet65
/oet65c.pdf
Health Canada limits for the general population; consult Safety Code 6, obtainable
from Health Canada’s website:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-eng.php
Santé Canada limite pour la population générale; consulter le Code de sécurité 6,
disponible sur le site Web de Santé Canada:
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/radio_guide-lignes_direct-fra.php .
Personal Safety
WARNING: HOT SURFACE. DO NOT TOUCH.
The RDL-3000 Ellipse TMA Sector Controller system is rated for operation at extreme
ambient temperatures. When operating in high temperature conditions, the chassis
surface area can be higher than the ambient temperature and personal thermal
protection should be employed for any maintenance or inspection activity.
Electrical Safety
The equipment meets the requirements for class I EN 60950-1 (protection against
electric shock).
All external circuits are TNV-1 (as defined in EN 60950-1).
All equipment must be grounded before the power cable is connected.
For electrical safety the DC power supply shall have reinforced insulation to the
mains supply.
Electrical Safety Compliance / Conformité à la Sécurité Electrique
The RDL-3000 system hardware has been tested for compliance to the electrical safety
specifications listed in the following table.