REDRAGON K585 DITI ELITE User manual

DA
REDRAGON
DITI ELITE
MECHANICAL GAMING KEYBOARD
2.4G wireless gaming keypad
e scan here to . .
aaaaaaaaaaaaaaaaaa
Operating
Instructions

Dear user
Thank you for choosing our REDRAGON product. To protect your rights and for
better customer service, we ask that you note our warranty rules.
1. Within guaranty period, repair is guaranteed for failure due to electrical circuit
problems. Other damages, such as disassembly, hard impacts, submersion into water,
plugging into improper current or voltage, and damage caused by natural disasters
such as fire, flood, or earthquake are not included.
2. Consumable parts (such as foot pad) and spare parts replacement are not included in
our warranty.

OS support
Windows XP/Vista/Win7/Win8/Win10
Basic Operation:
How to connect the keyboard with a computer
Wired Connection
1. Take out the USB to USB C cable in the package and connect the keypad with your
computer.
2. Slide the power switch on the bottom of the keyboard to Power On .
3.The computer will recognize and configure the keypad automatically.
4.The keypad will be ready for use when the configuration is finished. The LED of the keys
will light on.
5.The keypad is under recharging whatever the power switch is put to ON or OFF.It may
take about four hours for the keypad to be fully recharged.
Wireless Connection
1. Take out the USB receiver in the package and plug it into any available USB port on
your computer.
2. Slide the power switch on the bottom of the keypad to Power On.
3.The computer will recognize and configure the keypad automatically.
4.The keypad will be ready for use when the configuration is finished. The LED of the
keypad will light on.
5. Recharge the keyboard when the indicator (the LED on space bar) is flash in Red,the
indicator will turn to gree after full charge.

Function Introduction
1. Computer USB port interfaces with the keyboard without needing to install drivers or
software.
2. Detachable cable Type C to USB, cell phone cable are available.
3.There are 7 backlighting effects by press FN+Space: Go with the stream, The trial of
Light, Ripple Graff, Flowers blooming, Pass without Trace,Stars,both ways
4. FN+ESC: Press and hold for 3 seconds ,back to factory setting.
5.4 Pre-set backlights modes:
M1 (Default as F9) Go with the stream
M2(Default as F10) The trial of Lights
M3 (Default as F11) The Ripple Graff
M4(Default as F12) Pass without trace
6.7 Macro keys for recording: G1-G5 (G1-G5 default as F1-F5),~,T.
7.How to recording by macro keys?
Step 1: Press REC key, get ready for recording.
Step 2: select the light modes by press M1-M4.
Step 3: Select the macro key from 7 buttons(G1-G5,~,T).
Step 4: Input the keys to be recorded
(7 Macro keys G1,G2,.G3,G4,G5,~,T are not available for recording).
Step 5: Press REC to save the recording.
Noted: Every macro recording need to be coordinate with a light mode while it is
recording and play.
For example: Record 123 on G1 at Light mode M1: REC =% M1=—» G1—» 123 —» REC
8. How to play a macro?
For example: M1=—9 G1
9. How to delete a macro?
Press FN+ESC to delete all macro

How to Reconnect the keypad with the USB Receiver
The keypad may lost connection with the USB receiver for some occasional reasons such
as strong magnet, violent vibration. So you may need to reconnect the keyboard with the
USB receiver. In this case, unplug the receiver and plug it back again,Press FN+Q to pair,
The space bard will light on in blue, then keyad LED change back to the previous light
effect . The reconnection will be completed and you can use the keypard then.
FAQ
1. If the keyboard doesn’t respond, please check if the keyboard USB cable is correctly
inserted into the corresponding USB port on the computer, or try another USB port on
the computer.
2. If you spill liquid on the keyboard, please remove keyboard USB cable from the
computer immediately. Wipe up excess liquid and put the keyboard in a warm place
(for instance, under a lamp) to let the keyboard dry naturally before using again.
GO
QUALITY
ASSURED

FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions (1)this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.