RedShark Bikes ADVENTURE User manual

UNBOXING &ASSEMBLY instructions
Before anything, read user's manuals of this water bike to ensure correct usage through understanding. After reading, store them in a safe place for future
reference. Incorrect handling of this product could possibly result in personal injury or physical damage. The manufacturer assumes no responsibility for any damage caused by
mishandling that is beyond normal usage defined in these manuals of this water bike
GB: WARNING If you don't understand something please contact to Red Shark bikes.
ES: IMPORTANTE Si no entiende algo, por favor contacte con Red Shark Bikes.
F: IMPORTANT Si vous ne comprenez pas quelque chose, veuillez contacter Red Shark Bikes.
DE: ACHTUNG Wenn Sie etwas nicht verstehen, wenden Sie sich bitte an Red Shark Bikes.
I: IMPORTANTE se non capisci qualcosa, contatta Red Shark Bikes.
P: IMPORTANTE Se você não entender alguma coisa, entre em contato com a Red Shark Bikes.
RUS: ВАЖНО Если вы что-то не понимаете, пожалуйста, свяжитесь с Red Shark Bikes.
NL: BELANGRIJK als u iets niet begrijpt, neem dan contact op met Red Shark Bikes
S: VIKTIGT Om du inte förstår något, vänligen kontakta Red Shark Bikes.
JP: 重要なことがわからない場合は、Red Shark Bikesにお問い合わせください。
BIKE SURF
(Personal Water Craft)
IF YOU DO NOT AGREE FULLY TO ALL OF THESE PROVISIONS, YOU SHOULD NOT USE RED SHARK BIKES PRODUCTS.

ASSEMBLY INSTRUCTIONS
ENJOY model
FITNESS model
ADVENTURE model

ENJOY model
PARTS & elements

FITNESS model
PARTS & elements

PARTS & elements
ADVENTURE model

1. Please open the 2 boxes (from top side) and carefully remove
all parts from the box.
2. Remove all plastic bags and protections carefully.
WARNING: Plastic bags can be dangerous, to avoid danger of suffocation,keep all the bags
away from all babies, children, and house pets. Do not use in cribs, beds, carriages or
playpens. Tear up bag beforethrowing away.
3. Read the Packing List (outside the box)
and check if there are all the elements
ASSEMBLY INSTRUCTIONS

ENJOY model
1. FRAME A
5. Seat post CLAM
7. BOARD
3. FIN
2. BOTTLE
3. BOTTLE cage
6. TRANSMISSION
9. GRIPS
10. STEM
11. SADDLE
12. Seat POST
13. RUDDER
14. Rudder POST
22. REPAIR kit
15. Frame CLAM 16. PEDALS:
LEFT &
RIGHT
8. HANDLE bar
18. PROPELLER B 21. AIR PUMP
20. MULTI-TOOL KIT
7. BOARD BELT
0. PACKING list (outside the box)
PARTS & elements
33. SADDLE cover
TRAVEL bag
18. PROPELLER C
1. FRAME B
16. PEDALS:
CRANK
Travel bag
STRAPS
1. FRAME C
15. Frame CLAM

FITNESS model
PARTS & elements
1. FRAME A
5. Seat post CLAM
7. BOARD
3. FIN
2. BOTTLE
3. BOTTLE cage
6. TRANSMISSION
9. GRIPS
10. STEM
11. SADDLE
12. Seat POST
13. RUDDER
14. Rudder POST
22. REPAIR kit
15. Frame CLAM
16. PEDALS:
LEFT &
RIGHT
8. HANDLE bar
18. PROPELLER C
21. AIR PUMP
20. MULTI-TOOL KIT
7. BOARD BELT
0. PACKING list (outside the box)
TRAVEL bag
18. PROPELLER D
1. FRAME B
16. PEDALS:
CRANK
Travel bag
STRAPS
1. FRAME C
15. Frame CLAM
18. PROPELLER A
18. PROPELLER B
9. Frame NET
Water PROOF
BAG
9. GRIPS

PARTS & elements
1. FRAME A
5. Seat post CLAM
7. BOARD
3. FIN
2. BOTTLE
3. BOTTLE cage
6. TRANSMISSION
9. GRIPS
10. STEM
11. SADDLE
12. Seat POST
13. RUDDER
14. Rudder POST
22. REPAIR kit
15. Frame CLAM
16. PEDALS & CRANKS
left & right
8. HANDLE bar
18. PROPELLER A 21. AIR PUMP
20. MULTI-TOOL KIT 7. BOARD BELT
0. PACKING list (outside the box)
33. SADDLE cover
TRAVEL bag
18. PROPELLER B
1. FRAME B
Travel bag
STRAPS
1. FRAME C
15. Frame CLAM
ADVENTURE model
35. Phone holder
Water PROOF BAG
Water PROOF BAG
HANDLER BAG
Top frame BAG
NET rear board
Rear saddle
BAG

4. BOARD assembly
4.1. Extend the board
ASSEMBLY INSTRUCTIONS

4. BOARD assembly (Puff up /step 1 from 2)
4.2.Use the AIR PUMP to have only a LITTLE PRESSURE to get the basic shape.
ASSEMBLY INSTRUCTIONS
KEEP ATTENTION:
T h e A & B H o l e s s u r f a c e : m u s t b e c o m p l e t e l y c l e a n
f r o m d u s t , s a n d a n d o t h e r d i r t y e l e m e n t s . I f n o t i t
c o u l d d a m a g e o n t h e b o a r d s k i n .
I f y o u f i n d a i r l e a k a g e o n t h e v a l v e , u s e t h e b l a c k
t o o l ( i n c l u d e d o n t h e r e p a i r k i t t o o l s ) t o t i g h t o r t o
d i s a s s e m b l e t h e v a l v e a n d c h e c k i f i s d i r t y a n d y o u
c a n c l e a n i t .
B. Board HOLE (rear) A. Board Rudder HOLE (front)
Puff Up to 1 psi (approx.)
Unscrew the cap. Check the position of the
valve spout
Press 1 time or 2 times
Insert the air
pump
Puff up the air
to 1 psi Remove the
air pump

5. FRAME assembly
ASSEMBLY INSTRUCTIONS
5.1 CHOSE the frame piece “A”:
C
B
A

ASSEMBLY INSTRUCTIONS
Board
In the FRONT HOLE
5. FRAME assembly
KEEP ATTENTION:
The A&BHoles surface, must be completely
clean from dust, sand and other dirty elements. If
not it could generate damages on the board skin.
Please clean always before.
AVOID THE INTERFERENCES from
the rudder and propeller with the board surface
(holes A and B) if not it could generate damages
on the board.
Board with soft air pressure (From 0,01 to 0,5 psi)
5.1 INSERT the frame “A” in the front hole with a little air
pressure in the board
RECOMENDATION: Please us an small STOOL
(not included).
Suggestion: You can use a cloth rag to cover the rudder.

ASSEMBLY INSTRUCTIONS
6. HANDLEBAR assembly
6.1 Insert the handlebar in the STEM
TIGHT the 4 screws:
TORQUE SPECIFICATIONS
6 Newtons

ASSEMBLY INSTRUCTIONS
7. RUDDER assembly
7.1 Insert the rudderBAR in to the frame
5.2. Pull the ruderpost
up to the screw
TOP hole
BOTTOM hole

ASSEMBLY INSTRUCTIONS
7. RUDDER assembly
7.2 Insert the rudderpost to the STEM
7.3. Line up the
handle bar with
the rudder.
7.4 Tight the 2 screws
Handle Bar
Stem
ALIGNMENT WITH THE RUDDER bar
With the white mark in the center of the stem.
TORQUE SPECIFICATIONS
6 Newtons

7. RUDDER assembly
ASSEMBLY INSTRUCTIONS
7.5 Unscrew wing nut
RUDDER FUNCTION
“T”(transpor)
RUN
1
Level I
to GO
POSITIONS:
T: transport
•I: level1
•II: Level 2
•III: Level 3
7.7 Screw wing nut
7.6 Chose the position
“T”
for transport
TIGHT the wing nut:
TORQUE SPECIFICATIONS
3 Newtons

8. FRAME “B” assembly
ASSEMBLY INSTRUCTIONS
8.1 CHOSE the frame piece “B”:
CA
B

8. FRAME “B” assembly
ASSEMBLY INSTRUCTIONS
8.3Untight the 3 bolts
8.2 TRANSMISION assembly:

ASSEMBLY INSTRUCTIONS
8.3 Transmission LEVEL assembly:
8. FRAME “B” assembly