RedShark Bikes ADVENTURE User manual

Unboxing, assembly, warnings &precautions
BIKE SURF
(Personal Water Craft)
ASSEMBLY INSTRUCTIONS
1

Before anything, read user's manuals
of this water bike to ensure correct usage through understanding. After reading, store them in a safe place for future reference. Incorrect handling of this product could
possibly result in personal injury or physical damage. The manufacturer assumes no responsibility for any damage caused by mishandling that is beyond normal usage
defined in these manuals of this water bike
GB: WARNING If you don't understand something please contact to Red Shark bikes.
ES: IMPORTANTE Si no entiendealgo, por favor contacte con Red Shark Bikes.
F: IMPORTANT Si vous ne comprenez pas quelque chose, veuillez contacter Red Shark Bikes.
DE: ACHTUNG Wenn Sie etwas nicht verstehen,wenden Sie sich bitte an Red Shark Bikes.
I: IMPORTANTEse non capisci qualcosa,contatta Red Shark Bikes.
P: IMPORTANTE Se você não entender alguma coisa, entre em contato com a Red Shark Bikes.
RUS: ВАЖНО Если вы что-то не понимаете,пожалуйста, свяжитесьс Red Shark Bikes.
NL: BELANGRIJK als u iets niet begrijpt, neem dan contact op met Red Shark Bikes
S: VIKTIGT Om du inte förstår något, vänligenkontakta Red Shark Bikes.
JP: 重要なことがわからない場合は、RedShark Bikesにお問い合わせください。
IF YOU DO NOT AGREE FULLY TO ALL OF THESE PROVISIONS, YOU SHOULD NOT USE RED SHARK BIKES PRODUCTS.
2

MODELS:
ENJOYmodel
FITNESSmodel
ADVENTUREmodel
3

ENJOYmodel
4

FITNESS model
5

ADVENTURE model
6

UNBOXING
1. Open the box at the top and carefully remove all parts
from the box.
2. Remove all plastic bags.
WARNING: Plastic bags can be dangerous. To avoid any risk of suffocation, keep all
bags out of the reach of all babies, children and pets. Do not use in cribs, beds, strollers,
or playpens.Tear the bag before throwingit away.
3. Read the packing list (taped outside the box) and confirm all items.
7

ENJOYmodel
1. FRAME A
5. Seat post CLAM
7. BOARD
3. FIN
2. BOTTLE
3. BOTTLE cage
6. TRANSMISSION
9. GRIPS
10. STEM
11. SADDLE
12. Seat POST
13. RUDDER
14. Rudder POST
22. REPAIR kit
15. Frame CLAM 16. PEDALS:
LEFT &
RIGHT
8. HANDLE bar
18. PROPELLER B 21. AIR PUMP
20. MULTI-TOOLKIT
7. BOARD BELT
0. PACKING list (outside the box)
33. SADDLE cover
TRAVEL bag
18. PROPELLER C
1. FRAME B
16. PEDALS:
CRANK
Travel bag
STRAPS
1. FRAME C
15. Frame CLAM
SCREWS
BOLTS
Frame
PLATES
PARTS & components
8

FITNESS model
1. FRAME A
5. Seat post CLAM
7. BOARD
3. FIN
2. BOTTLE
3. BOTTLE cage
6. TRANSMISSION
9. GRIPS
10. STEM
11. SADDLE
12. Seat POST
13. RUDDER
14. Rudder POST
22. REPAIR kit
15. Frame CLAM 16. PEDALS:
LEFT &
RIGHT
8. HANDLE bar
18. PROPELLER C
21. AIR PUMP
20. MULTI-TOOLKIT
7. BOARD BELT
0. PACKING list (outside the box)
TRAVEL bag
18. PROPELLER D
1. FRAME B
16. PEDALS:
CRANK
Travel bag
STRAPS
1. FRAME C
15. Frame CLAM
18. PROPELLER A
18. PROPELLER B
9. Frame NET
Water PROOF
BAG
9. GRIPS
SCREWS
BOLTS
Frame
PLATES
PARTS & components
9

PARTS & components
1. FRAME A
5. Seat post CLAM
7. BOARD
3. FIN
2. BOTTLE
3. BOTTLE cage
6. TRANSMISSION
9. GRIPS
10. STEM
11. SADDLE
12. Seat POST
13. RUDDER
14. Rudder POST
22. REPAIR kit
15. Frame CLAM
16. PEDALS & CRANKS
left & right
8. HANDLE bar
18. PROPELLER A 21. AIR PUMP
20. MULTI-TOOLKIT 7. BOARD BELT
0. PACKING list (outside the box)
33. SADDLE cover
TRAVEL bag
18. PROPELLER B
1. FRAME B
Travel bag
STRAPS
1. FRAME C
15. Frame CLAM
ADVENTURE model
35. Phone holder
Water PROOF BAG
Water PROOF BAG
HANDLER BAG
Top frame BAG
NET rear board
Rear saddle
BAG
SCREWS
BOLTS
Frame
PLATES
10

NUTS, screws and others
2
10
2
2 4
2
OPTIONAL:
For a permanent frame
assembly
11

4. BOARD assembly
4.1.Extendtheboard
ASSEMBLY INSTRUCTIONS
12

4. BOARD assembly (Puff up /step 1 from 2)
4.2.Use the AIR PUMP to haveonlya LITTLEPRESSUREtoget thebasic shape.
ASSEMBLY INSTRUCTIONS
KEEP ATTENTION:
T h e A & B H o l e s s u r f a c e : m u s t be c o m p l et el y
c l e a n f r o m d u s t , s a n d and o t h er d i r t y el e m en t s .
If not it c ou l d d am a g e on t he b oar d s k in .
If y o u f i n d a i r l e a k a g e on t h e v a l v e , u s e t h e
b l a c k t o o l ( i n c l u d e d on t h e r e p a i r k i t t o o l s ) to
t i g h t or to d i s a s s e m b l e t h e val v e and c h e c k if is
d ir t y an d yo u c a n c l ea n it .
B. BoardHOLE(rear) A. BoardRudderHOLE(front)
Puff up to:
0,5 psi(approx.)
board must be soft
Unscrew the cap. Check the positionof the valvespout
Press 1 timeor 2 times Insert the air
pump Puffup the air to 1 psi Remove the air pump
13

5. FRAME assembly
ASSEMBLY INSTRUCTIONS
5.1 CHOSE the frame piece“A”:
C
B
A
14

ASSEMBLY INSTRUCTIONS
In the FRONT HOLE
5. FRAME assembly
KEEP ATTENTION:
The A&BHoles surface, must be completely
clean from dust, sand and other dirty elements. If
not it could generate damages on the board skin.
Please clean always before.
AVOID THE INTERFERENCES from
the rudder and propeller with the board surface
(holes A and B) if not it could generate damages
on the board.
Board with soft air pressure 0,5 psi
5.1 INSERT the frame “A” from the deck (TOP side)
RECOMMENDATION:Please us an small STOOL
(not included).
Suggestion: You can use a cloth rag to cover the rudder.
Board
15

ASSEMBLY INSTRUCTIONS
6. HANDLEBAR assembly: ENJOY & ADVENTURE models.
6.1 Insertthe grips in the handlebar
ALCOHOL
*not included
16

ASSEMBLY INSTRUCTIONS
6. HANDLEBAR assembly
6.1 Insertthe handlebar inthe STEM
6.2 TIGHTthe4 screws:
TORQUE SPECIFICATIONS:
6 Newtons 17

ASSEMBLY INSTRUCTIONS
6. HANDLEBAR assembly: FITNESS model.
6.1 Insertthe grips in the handlebar
ALCOHOL
*not included
18

ASSEMBLY INSTRUCTIONS
6.1 Insertthe handlebar inthe STEM
6.2 TIGHTthe4 screws:
TORQUE SPECIFICATIONS:
6 Newtons
6. HANDLEBAR assembly: FITNESS model.
19

ASSEMBLY INSTRUCTIONS
7. RUDDER assembly
7.1Insertthe rudderBAR in to the frame
7.2.Pullthe ruderpost
up to the screw
TOP hole
BOTTOM hole
20