Redtronic ML4 Owner's manual

MANUFACTURED IN THE
UNITED KINGDOM
PAGE 1
Part Number Colour Voltage Amps Warranty
EM355AC 10-30VDC 400mA 2 years
EM335BC 10-30VDC 400mA 2 years
EM335RC 10-30VDC 400mA 2 years
EM335BRC 10-30VDC 400mA 2 years
V1.1 (M025)
[phone] [email protected].UK WWW.REDTRONIC.CO.UK
Installation and Operation Instructions
ML4
The ML4 is a petite, covert style directional and is ideal for customers wanting to avoid visible mounting
screws. The ML4 comes as standard with a highly effective adhesive (rear only) making it only necessary
to drill a single cable entry hole to install. Considering the extremely slender depth (12mm), it is a perfect
solution for applications where space is restricted, especially inside the tailgate where a slim lamp is
required. An optional extra includes a window pod for window mounting.
Product Description
Flash Patterns
1Mega-Flash
2Quad
3Triple
4Double
5Single
6Hyper

MANUFACTURED IN THE
UNITED KINGDOM
[phone] [email protected].UK WWW.REDTRONIC.CO.UK PAGE 2
V1.1 (M025)
Cable Connections
Function Cable Colour Description
Power 1 +ve Red Wire Power 1 – powers primary colour (left*)
Power 2 +ve Orange Wire Power 2 - powers secondary colour* (right*)
Ground -ve Black Wire 0v ground / earth
Pattern +ve Brown Wire Changes the flash pattern by momentarily applying to a positive. Apply
to +ve for 2-3 seconds to revert to quad flash (pattern 1)
Synchronisation Yellow Wire Link to other Redtronic products
*only applicable to dual / split colour models
Installation
R10
EMC
Voltage Range 10-30VDC
Type Ultra-thin moulded front face
Number of LEDs 4
Amps / Current Peak Max 400mA at 12VDC
IP Rating IP65 protection against dust and water ingress
Compliant EMC R10
Weight 14g
Operating Temperature -40 to +105°C
Lens Material Ultra-strong UV stabilised polycarbonate lens
Enclosure Material Thermoplastic polyamide moulding
Mounting Adhesive pad
Warranty 2 years
Technical Information
Connecting the ML4 directionals to a vehicle battery / power source requires the black wire to be
connected to the negative (-ve) terminal, and either the red wire (V1) or the orange wire (V2) to be
connected to positive (+ve) terminal. Patterns need to be set in the same manner as the primary red wire
colour. Disconnect the red wire to set the secondary functions as desired.
To set the flash pattern:
With the ML4 powered on, the brown wire should be connected to positive (+ve) terminal from the power
source momentarily, to change to the next pattern. Either touch the wire topositive (+ve) briefly, or connect
via a momentary switch and press to change pattern.

To synchronise ML4’s:
When the desired flash pattern has been set, connect the yellow wires from each ML4 together, this will
ensure all ML4’s flash in a synchronised format. Note: Do not apply yellow wires to positive (+ve).
Do not attempt to sync Redtronic products with any other manufacturer’s products.
MANUFACTURED IN THE
UNITED KINGDOM
[phone] [email protected].UK WWW.REDTRONIC.CO.UK PAGE 3
V1.1 (M025)
Installation Diagrams

MANUFACTURED IN THE
UNITED KINGDOM
[phone] [email protected].UK WWW.REDTRONIC.CO.UK PAGE 4
Cleaning and Maintenance
Please refer to our ‘How to care for your Redtronic Polycarbonate Products” and our “shrouds and mounting
pods” document.
Warranty and Liability
Redtronic warrants that on the date of purchase, this product will conform to Redtronic specifications for
this product (which are available from Redtronic upon request). This product benefits from a 2-year warranty
from the date of purchase. Warranty disclaimer: shrouds / mounting pods are not covered under warranty.
V1.1 (M025)