REDZ BSB Series User manual

BSB Series Industrial Unmanaged EthernetBSB Series Industrial Unmanaged Ethernet
Switch with 10/100Base-T(x) Ports and/orSwitch with 10/100Base-T(x) Ports and/or
BPL ( Broadband Power Line Link) UserBPL ( Broadband Power Line Link) User
ManualManual
1. About BSB Series Industrial Unmanaged Ethernet Switch1. About BSB Series Industrial Unmanaged Ethernet Switch
BSB Series Industrial Unmanaged Ethernet Switches are designed for industrial-grade Ethernet, and
particularly for facilities of rugged industry and infrastructure. BSB Series Industrial Unmanaged Ethernet
Switches are tailored to perform various features, such as wide temperature, wide range power input
range... etc. Thus, BSB Series Industrial Unmanaged Ethernet Switches are the best choice for facility
management, sewage treatment, power utility, telecommunication, transportation and all other
applications that require reliable Ethernet connectivity.
BSB Series has models also with REDZ Broadband Power Line (BPL) communication. BPL link allows device
to communicate with full transparent TCP/IP standard over Low Voltage power lines and allows easy
connection between TCP/IP based terminals without use of extra cables.
2. Hardware Features2. Hardware Features
BSB Series Industrial Unmanaged Ethernet Switches has the versions with and without BPL (Broadband
Power Line) Link.
2.1 Features2.1 Features
Supports up to 8 x 10/100Base-T(X) ports
AC or DC wide range power options
Supports Full/Half-Duplex, auto MDI/MDI-X on each port
Wide operating temperature range from -25 to 70 °C AC and -40 to 85 °C DC power input versions

Rugged Metal IP-40 housing design
DIN-Rail mounting
2.2 Extra Features for Models with BPL2.2 Extra Features for Models with BPL
Supports up to 7 x 10/100Base-T(X) ports + 1 x BPL link
Wide range 3 phase AC input
Supports up to 30Mbps PHY rate on BPL with Up to 10 hops and 1000 nodes
Up to 432 sub-carriers from 2 to 28MHz analog bandwidth
Support LDPC-C FEC with 128-bit AES core
Plug and play with Master/Slave selection via switch
3. Installation3. Installation
Each switch has a Din-Rail kit on rear panel. The Din-Rail kit helps switch to fix on the Din-Rail. Slant the
switch and mount the metal spring to Din-Rail.
Then Push the switch toward the Din-Rail until you heard a “click” sound.

4. Front Panel Description4. Front Panel Description
4.14.1 BSB115 & BSB215BSB115 & BSB215

1. 10/100Base-T(X) Ethernet ports 1, 2, 3 and 4.
2. ETHERNET Activity LEDs for port 1, 2, 3 and 4. Blinks during ethernet activity.
3. 10/100Base-T(X) Ethernet port 5.
4. ETHERNET Activity LED for port 5. Blinks during ethernet activity.
4.24.2 BSB118 & BSB218BSB118 & BSB218

1. 10/100Base-T(X) Ethernet ports 1, 2, 3 and 4.
2. ETHERNET Activity LEDs for port 1, 2, 3 and 4. Blinks during ethernet activity.
3. ETHERNET Activity LEDs for port 5, 6, 7 and 8. Blinks during ethernet activity.
4. 10/100Base-T(X) Ethernet ports 5, 6, 7 and 8.
4.34.3 BSB612BSB612
1. 10/100Base-T(X) Ethernet port.

2. BPL Activity LED. Blinks during BPL & Ethernet activity.
3. BPL Link LED. LED Turns ON if the link can be established.
4. Master Indication LED. LED Turns ON if the device is started as “Master” device.
5. Switch position to select the device as “Master” or “Slave”. Device must be repowered after
changing the setting to take into effect.
4.44.4 BSB615BSB615
1. 10/100Base-T(X) Ethernet ports 1, 2, 3 and 4.
2. ETHERNET Activity LEDs for port 1, 2, 3 and 4. Blinks during ethernet activity
3. BPL Activity LED. Blinks during BPL & Ethernet activity
4. BPL Link LED. LED Turns ON if the link can be established.
5. Master Indication LED. LED Turns ON if the device is started as “Master” device.
6. Switch position to select the device as “Master” or “Slave”. Device must be repowered after
changing the setting to take into effect.

4.54.5 BSB618 BSB618
1. 10/100Base-T(X) Ethernet ports 1, 2, 3 and 4.
2. ETHERNET Activity LEDs for port 1, 2, 3 and 4. Blinks during ethernet activity.
3. ETHERNET Activity LEDs for port 5, 6, and 7. Blinks during ethernet activity.
4. 10/100Base-T(X) Ethernet ports 5, 6, and 7.
5. BPL Activity LED. Blinks during BPL & Ethernet activity.
6. BPL Link LED. LED Turns ON if the link can be established.
7. Master Indication LED. LED Turns ON if the device is started as “Master” device.
8. Switch position to select the device as “Master” or “Slave”. Device must be repowered after
changing the setting to take into effect.

5. Top Panel Description5. Top Panel Description
5.1 BSB115 & BSB1185.1 BSB115 & BSB118
1. Power Input DC: 5-60V DC. Polarity protected so that the power input can be connected in any
direction.
2. Power LED: Turns ON when there is power in device.
3. Reset Button: Reset the device.

5.2 BSB215 & BSB2185.2 BSB215 & BSB218
1. Power Input AC: 90 - 265V AC (100 – 370V DC), 47Hz to 63Hz AC input.
2. Power LED: Turns ON when there is power in device.
3. Reset Button: Reset the device.

5.3 BSB612 & BSB615 & BSB6185.3 BSB612 & BSB615 & BSB618
1. Power Input AC: 3 phase input, 110V–240V/50-60Hz. It is also ok to connect only single phase to
the device such as L1-N connection only.
AC Power supply use L1-N only. Phase 2-3 connections are used to BPL signal transmission.
2. Power LED: Turns ON when there is power in device.
6. Ethernet Cables6. Ethernet Cables
BSB Series Industrial Unmanaged Ethernet Switches have standard Ethernet ports. According to the link
type, the switches use CAT 3, 4, 5, 5e UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs).
6.1 Cable Type and Specifications6.1 Cable Type and Specifications
CableCable TypeType Max. LengthMax. Length ConnectorConnector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45

6.2 ETH Cable Pin Assignments6.2 ETH Cable Pin Assignments
With 100BASE-TX/10BASE-T cable, pins 1 - 2 are used for transmitting data and pins 3 - 6 are used for
receiving data.
Pin NumberPin Number DescriptionDescription
1 TD+
2 TD-
3 RD+
4 Not Used
5 Not Used
6 RD-
7 Not Used
8 Not Used
7. Connection Diagrams7. Connection Diagrams
BSB Series Industrial Unmanaged Ethernet Switches connections vary based on with and without BPL
(Broadband Power Line ) Link versions.
7.1 BSB612 & BSB615 & BSB618 Connection Diagram7.1 BSB612 & BSB615 & BSB618 Connection Diagram

7.27.2 BSB115 & BSB118 & BSB215 & BSB218 Connection DiagramBSB115 & BSB118 & BSB215 & BSB218 Connection Diagram
8. System Comparison Between CAT5 and BPL Links8. System Comparison Between CAT5 and BPL Links
CAT5 Based SystemCAT5 Based System BPL Link Based SystemBPL Link Based System
Media CAT5 Power Line
Bandwidth 100Mbps Up to 30Mbps
Re-Wire Yes No, Using existing Power Line
Span <100m <600m
Multiple Nodes N/A Up to 10 hops/1000 nodes
Encryption Yes, but difficult to configure Yes, Plug & Play
Installment Difficult Easy, simply user power line
Installment Cost High Low
Total Cost High Low

9. Ordering Information9. Ordering Information
BSB115:BSB115: Industrial Unmanaged Ethernet Switch, 5 x 10/100 T(x) ETH ports, 5-60V DC Power Input
BSB118: BSB118: Industrial Unmanaged Ethernet Switch, 8 x 10/100 T(x) ETH ports, 5-60V DC Power Input
BSB215:BSB215: Industrial Unmanaged Ethernet Switch, 5 x 10/100 T(x) ETH ports, 90 - 265V AC (100 – 370V DC),
47Hz to 63Hz AC Power Input
BSB218:BSB218: Industrial Unmanaged Ethernet Switch, 8 x 10/100 T(x) ETH ports, 90 - 265V AC (100 – 370V DC),
47Hz to 63Hz AC Power Input
BSB612:BSB612: Industrial Unmanaged Ethernet Switch, 1 x 10/100 T(x) ETH ports + 1 x BPL (Broadband Power Line)
Link, 3 Phase AC Power Input, 110V–240V/50-60Hz
BSB615:BSB615: Industrial Unmanaged Ethernet Switch, 4 x 10/100 T(x) ETH ports + 1 x BPL (Broadband Power Line)
Link, 3 Phase AC Power Input, 110V–240V/50-60Hz
BSB618:BSB618: Industrial Unmanaged Ethernet Switch, 7 x 10/100 T(x) ETH ports + 1 x BPL (Broadband Power Line)
Link, 3 Phase AC Power Input, 110V–240V/50-60Hz
10. Product Selection10. Product Selection
Model
5-60V
DC
Power
Input
90 -
265V AC
(100 –
370V
DC), 47Hz
to 63Hz
AC
Power
Input
3 Phase AC
Power input,
110V–
240V/50-
60Hz AC
Power Input
8 x
10/100 T(x)
ETH Ports
7 x
10/100 T(x)
ETH Ports
5 x
10/100 T(x)
ETH Ports
4 x 10/100
T(x) ETH
Ports
1 x 10/100
T(x) ETH Ports
BPL (Broadband
Power Line) Link
BSB115 X X
BSB118 X X
BSB215 X X
BSB218 X X
BSB612 X X X
BSB615 X X X
BSB618 X X X