Reelcraft Industries, Inc. D8600 OLP User manual
1. Do not use reel at higher pressures or temperatures
than listed on the back of this bulletin.
2. Remove all spring tension before beginning
dissassembly process.
SAFETY
INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Operating Instructions
Series D8000 Spring Driven Hose Reels
Low Pressure Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: 800-444-4587 / 260-248-2605
Form# 4768-84 Rev: 1/2016
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
Dimensions
A21 1/8”
B 19”
C7 7/8”
D3 3/4”
E9 1/4”
D8600 OLP D8650 OLP D8800 OLP D8840 OLP
D8640 OLP D8670 OLP D8830 OLP D8850 OLP
Caution: When changing guide arm positions, the U-bolt must
be placed in the proper location as instructed below. The reel
can “latch out” during use if this instruction is not adhered to.
Series D8000 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Description #
Req. D8600 OLP D8640 OLP D8650 OLP D8670 OLP D8800 OLP D8830 OLP D8840 OLP D8850 OLP
1Hose Assembly 1 None 601014-40 S601017-50 S601017-70 None 601021-30 601019-40 601021-50
2Swivel Assembly 1 S600923-1 S600923-1 S600923-1 S600923-1 S600923-1 S600923-1 S600923-1 S600923-1
3Sheave Assembly 1 S260011 S260011 S260011 S260011 S260011 S260011 S260011 S260011
4Drive Spring Assembly 1 S260028 S260028-1 S260028-1 S260028 S260037 S260037 S260037 S260037
5Spring Arbor Assembly 1 S600621 S600621 S600621 S600621 S600621 S600621 S600621 S600621
6 Gasket 1 S260069 S260069 S260069 S260069 S260069 S260069 S260069 S260069
7Spring Case Assembly 1 S260074 S260074 S260074 S260074 S260074 S260074 S260074 S260074
810-32 Hex Nut Nyloc 6 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15 S82-15
9Main Shaft 1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1 260442-1
10 1¼” Snap Ring 3 300007 300007 300007 300007 300007 300007 300007 300007
11 Bumper Stop 1 None 1-HR1004-3 1-HR1004-3 1-HR1004-3 None 2-HR1004-3 2-HR1004-3 2-HR1004-3
13 Guide Arm / Roller Assembly 1 260007 260007 260007 260007 260007 260007 260007 260007
14 5/16-18 x 1¼” Screw 3 507286 507286 507286 507286 507286 507286 507286 507286
15 1/2-13 Set Screw 1 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86 S35-86
16 1/2-20 Hex Nut 1 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8 S280-8
17 Base Casting 1 260073 260073 260073 260073 260073 260073 260073 260073
18 Latch Spring 1 S260067 S260067 S260067 S260067 S260067 S260067 S260067 S260067
19 Latch Bushing 1 S400012 S400012 S400012 S400012 S400012 S400012 S400012 S400012
20 10-24 x 1” Screw 1 300042 300042 300042 300042 300042 300042 300042 300042
21 Latch Pawl Assembly 1 S600083 S600083 S600083 S600083 S600083 S600083 S600083 S600083
22 3/8-24 Hex Jam Nut 1 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106 S76-106
23 Spring Case Stud 1 S260031 S260031 S260031 S260031 S260031 S260031 S260031 S260031
24 U-bolt 1 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440 3-117440
25 1/4-20 Nyloc Nut 2 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1 261650-1
27 Swivel Union 1 S257-26 S257-26 S257-26 S257-26 S257-26 S257-26 S257-26 S257-26
Hose I.D. and Length 3/8” x 70’ 3/8” x 30’ 3/8” x 50’ 3/8” x 70’ 1/2” x 50’ 1/2” x 30’ 1/2” x 40’ 1/2” x 50’
Reel Inlet Connection 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT 1/2” FPT
Max. Operating Pressure 500 PSI 300 PSI 300 PSI 300 PSI 500 PSI 300 PSI 300 PSI 300 PSI
Max. Operating Temperature 210 °F 150 °F 150 °F 150 °F 210 °F 150 °F 150 °F 150 °F
1
2
345678910
11
13
14
15
16
17
18
19
20
21
22
23
24
25
27
This manual suits for next models
7
Other Reelcraft Industries, Inc. Other manuals
