ZKTeco FHT2311 User manual

USER MANUAL
Full Height Turnstile
Applicable Models: FHT 2300 / 2400

1
Contents
Chapter 1 Product Introduction.........................................................................................................1
1.1 Model number and access control.......................................................................................1
1.2 Structures and dimensions...................................................................................................1
1.3 Mechanical system of FHT2300&FHT2400 series ..................................................................2
1.4 Electronic control system .....................................................................................................2
1.5 The working principle of full height turnstiles ......................................................................3
1.6 Product related parameters..................................................................................................3
Chapter 2 The Installation of the Device ............................................................................................4
2.1 Installation notes..................................................................................................................4
2.2 Installation position of the full height turnstile.....................................................................4
2.3 Installation and fixation of cables .........................................................................................4
Chapter 3 Menu Operation................................................................................................................8
3.1 Menu operation ...................................................................................................................8
3.3 Menu operation and description..........................................................................................8
3.4 System menu description.....................................................................................................9
Chapter 4 Product Maintenance......................................................................................................11
4.1 Mainframe-box maintenance.............................................................................................11
4.2 Movement maintenance....................................................................................................11
4.3 Power maintenance ...........................................................................................................11

1
Chapter 1 Product Introduction
1.1 Model number and access control
Access
Model
No C3-200 with two KR101E
reader
InBio260 with two FR1200/ID
reader
FHT2300 √
FHT2311 √
FHT2322 √
FHT2400 √
FHT2411 √
FHT2422 √
1.2 Structures and dimensions
FHT2000 series has stainless steel casing, which provides corrosion resistance and durability.
FHT2300’s appearance and dimensions are as shown in Figure 1-2A：
Figure 1-2A

2
FHT2400’s appearance and dimensions are as shown in Figure 1-2B：
Figure 1-2B
1.3 Mechanical system of FHT2300&FHT2400 series
The mechanical system of the full height turnstiles includes a mainframe box and a frame. The
direction indicator, core, control panel, access controller and lock are installed in the mainframe box.
The core component mainly consists of two solenoids, a spring and a transmission mechanism. The
frame supports the entire mainframe box.
1.4 Electronic control system
The electronic control system of the full height turnstile is composed of reader, control panel,
access controller, direction indicator, horn, and transformer.
Reader: The reader reads the data from the card and sends it to the controller.
Control panel: The control panel is the system’s control center that receives signals from the
controller. After the signals have been processed by the control panel, the control panel will deliver
commands to the indicator. .
Direction indicator: This indicator displays the current status of the sign at the channel, and directs
the pedestrian to pass the channel.

3
1.5 The working principle of full height turnstiles
1.5.1 After the power is turned on, the system will perform self-check. If no fault is detected, the
device will operate as usual. If a fault is detected, the system will display the related messages on
the LCD screen. This can be useful for error checking and troubleshooting.
1.5.2 When the reader detects a valid signal, the buzzer will give pedestrians a voice prompts to
remind pedestrians have been successful credit card. And then, the reader sends signals to the
access controller to request permission to pass through the passage. After the access controller
send the signals to the control panel, the control panel will send out a pass.
1.5.3 After receiving the signal from the access controller, the control panel sends signals to the
direction indicator and solenoid. Then the direction arrow will turn green. Also the solenoid will
loose that the pedestrian can push the rod to pass the passage.
1.6 Product related parameters
Dimensions(mm)
FHT2000: L = 1400, W = 1310, H = 2200
FHT2400: L = 1400, W = 1370, H = 2200
Communication
Interface
RS232 Input voltage
AC 100 - 120V/200 - 240V,
50 - 60Hz
Input control signal Switching signal
Output
voltage
DC 24V
Working environment Indoor/Outdoor
Relative
humidity
25% - 75%
Temperature -28℃~ 60℃Pass speed
RFID：Maximum 30/minute
Fingerprint：Maximum25/minute
Face：Maximum 15/minute
Vein：Maximum 15/minute

4
Chapter 2 The Installation of the Device
2.1 Installation notes
2.1.1 It is recommended that the full height turnstile should be installed on a cement platform with
50mm to 100mm in height.
2.1.2 It is recommended that the full height turnstile should not be used in corrosive environments.
2.1.3 Make sure the earth wire of the system is connected reliably reliably to prevent any personal
injuries or other accidents.
2.1.4 After completion of the installation, check the connection condition of earth wire, connector
assembly for connecting line and all moving parts with the device. Make sure the connection is
firm in order to prevent failure caused by long time operation. If any screw or part is not tightened,
please tighten.
2.2 Installation position of the full height turnstile
The installation position are subject to the size of the full height turnstile, as shown in Figure 2-2A.
Figure2-2A
2.3 Installation and fixation of cables
The following diagram shows the interface of the concealed cable. The input voltage for this full
height turnstile is AC100-120V/200-240V. The PVC conduits are buried 100mm below the ground,
with the height of the exposed part not not less than 100mm. To prevent water leakage to the

5
conduit, the conduit mouth needs to be bent back.
FHT2300&FHT2400 series installation holes are as shown in Figure 2-3A and Figure 2-3B.
Figure2-3A
Figure2-3B
Ø25 PVC pipe
Ø25 PVC pipe

6
Put the installation diagram on the floor. Using percussion to drill holes for M12 screws on the
corresponding position. Then install the screws to the corresponding positions. Next, place the
frame on top of the screw and fix it. After that, the mainframe-box is fixed on the frame. Finally
install the whole rotating part in the middle of the frame as shown in Figure 2-3C.
Figure2-3C
After fixing the device, open the mainframe-box to connect power wire and reader. Pull out the
reader and power cord from both sides of the column and connect to the corresponding interface.
Wiring diagram is as shown in Figure 2-3D.
1
2
3
3
4

7
Figure2-3D

8
Chapter 3 Menu Operation
3.1 Menu operation
1. After start-up, the LCD screen will display the current working mode.
2. There are 7 buttons on the panel:“”LEFT OPEN”,“RIGHT OPEN”,“MENU”,“UP”, “DOWN”,“OK”and“ESC”.
3. There is a RS232 communication Interface on the panel that can send a signal to the panel.
3.2 Button instruction
LEFT OPEN: Open the device to right.
RIGHT OPEN: Open the device to left.
MENU: Display the functions.
UP: Move up menu or add value.
DOWN: Move down menu or reduce value.
OK: Use to enter the menu item settings or to confirm the current value.
ESC: Use to return to the previous menu or cancel the current operation.
3.3 Menu operation and description
Press the "MENU" button, enter the password input interface, the default password is: "UP" key
press two times, "Down" key press four times, and then press "OK" to enter the menu interface. If
the operation is incorrect, press the ESC button go back to the previous menu, After entering the
menu, press "UP" and "DOWN" to select a function and then press "OK" to enter the function. Finally
press“UP”or “DOWN”to change the value, and then press“OK”to confirm.