Remington FR500 User manual

FR500, FR730, FR750
Use and Care Guide
When using an electrical appliance,
basic precautions should always be
observed, including the following.
Read all instructions before using
this shaver.
DANGER
To reduce the risk of electric shock:
■ Do not reach for an appliance that
has fallen into water. Unplug it
immediately.
■ Do not use while bathing or in the
shower.
■ Do not place or drop into water or
other liquid.
■ Do not place or store this appliance
where it can fall or be pulled into a
tub or sink.
■ Except when charging, always
unplug this appliance from the
electrical outlet immediately after
using.
■ Use only when the shaver is in dry
condition.
■ Detach the appliance from the
power supply cord before cleaning.
■ Do not submerge in water.
WARNING
To reduce the risk of burns, fire,
electric shock, or injury to persons:
■ An appliance should never be left
unattended when it’s plugged
in, except when charging a
rechargeable appliance.
■ Close supervision is necessary
when this appliance is used by,
on, or near children, or individuals
with special needs or certain
disabilities.
■ Use this appliance only for its
intended use as described in this
manual. Do not use attachments
not recommended by the
manufacturer.
■ Never operate this appliance if it
has a damaged cord or plug or if
it is not working properly, if it has
been dropped or damaged, or if it
has been dropped into water.
■ Keep the cord away from heated
surfaces.
■ Never drop or insert any object into
any of the appliance’s openings.
■ Household use only.■
Do not use outdoors or operate
where aerosol (spray) products
are being used or where oxygen is
being administered.
■ Always attach the plug to the
appliance, then to outlet. To
disconnect, turn all controls to OFF,
then remove plug from outlet.
■ Always pull on cord plug to unplug
from wall socket. Never pull on
electric cord.
IMPORTANT SAFETY
INSTRUCTIONS
■ Do not plug or unplug this appliance
when your hands are wet.
■ Do not use an extension cord
or a voltage converter with this
appliance.
■ Do not wrap the cord around the
appliance.
■ Always store this appliance and
cord in a moisture-free area.
Do not store it in temperatures
exceeding 140°F (60°C).
■ Detach removable power cords
SAvE ThESE INSTRUCTIONS
from appliance for storage.
■ Do not use this appliance with
a damaged or broken head or
cutters, as facial injury may occur.
■ Shavers, including the trimmer, are
for use on facial hair only. They
should not be used for shaving the
hair on your head or any other part
of your body.
■ The power unit is intended to be
correctly oriented in a floor mount
position.
About Your Shaver
* See "How to order shaver accessories" section on replacement parts.
Cord/Cordless – shaver can be used
with or without the power cord.
Battery Fuel Gauge
During use – Charging indicator
lights will flash to indicate that
shaver is on. Once turned off, the
battery indicator lights will display
the remaining battery capacity and
then turn off.
While charging – Charging indicator
light will flash, and then remain lit
one by one starting at the bottom to
indicate the charge level.
At full charge – All charging
indicator lights will continually
flash.
Worldwide Voltage – Shaver
automatically adapts to an outlet
voltage between 100V and 240V,
and 50/60 Hz.
Before using, read the important
safety instructions in front of the
manual.
1. Connect the cord
to the shaver and
then to the electrical
outlet. (Diagrams A
& B) The charging
indicator lights
will flash and then
remain lit up one by
one starting at the
bottom, indicating
charge level.
2. Charge your new
shaver for 8 hours
before its first use.
This first charge is
important to the shaver’s battery
life. (Diagram C)
A
B
8
C
Foil Assembly
Note that the foil assemly is not
reversible. If it does not go on
easily, reverse it and click into
Charging
3. Recharge the shaver when the
bottom fuel gauge indicator light
turns red.
**Use the product until the battery
is low. To preserve the life of the
batteries, let them fully run out
every six months, then recharge
them for a full 8 hours*
CAUTION!
■ Make sure the shaver and your
hands are dry when placing the
shaver on charge.
■ Always charge the shaver in a
cool, dry place.
face. Only apply
light pressure on
the shaving head
while shaving and
use short, circular
strokes. (Diagram E)
5. After shaving, turn the shaver off.
(Diagram D)
**Remington recommends that you
use your new shaver daily for up to
three weeks to allow time for your
hair and skin to become accustomed
to the new shaving system**
Shave
Shaving Tips
Before using, read the important
safety instructions in front of the
manual.
1. Begin by removing the protective
head guard from your shaver.
2. Press the on/off
button to turn on.
(Diagram D)
3. Stretch the skin with
your free hand so
the hairs stand upright.
4. Hold the shaving head so
all screens touch your skin
simultaneously. The independently
floating screens automatically
adjust to the contours of your
AD
■ Ensure your skin is dry and free
of oils.
■ Wait at least 15 minutes after
getting up before shaving, to ensure
your face is free of puffiness that
may be present from sleeping.
■ Always hold the shaver at a right
angle to the skin so the screens
are touching the skin with equal
pressure.
■ Stretch skin with the free hand
so hairs stand upright, making it
easier for them to enter the cutting
chamber.
■ Shave with short, circular strokes.
The use of short, circular motions in
stubborn areas may obtain a closer
shave, especially along the neck
and chin line.
■ Do not press hard against the skin
in order to avoid damage to the
foil heads.
Register Your New Product Today!
By registering your new Remington®product, you will receive these important benefits:
Proof of Ownership • Product Protection • Product Registration • Special Offers
Register online at: www.RemingtonProducts.com
FEATURE FR500 FR730 FR750
POWER SYSTEM Cord/Cordless Cord/Cordless Cord/Cordless
CHARGE TIME 90 Min 60 Min 60 Min
OPERATING TIME 35 Min 40 Min 30 Min
INDICATORS Fuel Gauge Fuel Gauge Fuel Gauge
VOLTAGE TYPE Worldwide Worldwide Worldwide
SPARE PART SPF-50 SPF-73 SPF-75
WASHABLE Yes Yes Yes
PIVOT LOCK No No Yes
E
Product Features
Shaver Parts
1. On/Off button
2. Screens
3. Intercept trimmer
4. Foil assembly
5. Hair pocket
6. Pivot lock
7. Cutter assembly
release buttons
8. Battery fuel gauge
9. Power port
10. Pop-up trimmer
11. Headguard
12. Power addaptor
13. Cleaning brush
14. Storage pouch
3
2
4
6
1
8
9
7
5FRONT
10
11
12
13
14

Monthly Cleaning:
1. Perform the daily
cleaning steps 1-4.
2. Place a drop of
liquid soap on
each cutter and
in the hairpocket.
(Diagram M)
3. Brush the soap
around vigorously
with the supplied
cleaning brush.
Be sure to work
the soap into the
corners of the
hairpocket and into
any especially dirty
cutters.
(Diagram N)
4. Add a small amount
of water to the
cutters.
5. Replace the foil
assembly.
(Diagram O)
6. Turn on the shaver
for approximately
30 seconds.
7. While the shaver is running, rinse
the foils under running water.
(Diagram P)
8. Turn off shaver.
9. Remove foil assembly. (Diagram H)
10.Rinse the cutters, hairpocket,
and foil assembly thoroughly.
(Diagram Q)
11. Shake off excess water.
12. Replace foil assembly.
(Diagram O)
13. Allow shaver to dry before next use.
Pop-up
release
switch
1
■ Do not remove or replace head
assembly while shaver is running
as it may cause damage to the
unit’s foils and cutters.
■ To clean the external surfaces of
the shaver, use a damp cloth. Do
not use strong detergents or other
chemicals.
■ To dry, wipe the surface of the
shaver with a dry towel. Do not use
a hair dryer or heater to dry the
shaver.
■ The shaver should not be used until
it has dried.
■ This product contains no user
serviceable parts.
The shaver is a
washable appliance.
The head assembly
part may be cleaned
under water.
Trim
Cleaning & Care
NOTE: **When cleaning your
shaver, make sure the shaver is
turned off and disconnected from
the power cord.**
For optimal shaver performance,
clean your shaver after each use.
CAUTION!
■ Shaver can be placed under running
water for cleaning only. Never
submerge the shaver in water.
Your Remington®electric shaver fea-
tures a pop-up trimmer.
■ Make sure shaver is turned off.
■ Place thumb on Pop-up Release
switch and push up.
■ Turn on shaver to engage trimmer.
■ When finished, turn shaver off.
■ Place thumb on Pop-up Release
switch and pull down.
2
3
Daily Cleaning:
1. Place thumb and
pointer finger on
Foil Assembly
Release Buttons
and push inward.
(Diagram H)
With your other
hand, pull Foil
Assemly upward,
exposing cutters.
2. Tap the stubble
from the foils and
cutters.
3. Use the cleaning
brush to sweep
any loose hairs
from the cutters,
hairpocket, and
trimmer. Pay
close attention
to cleaning out
the corners and
crevices inside
the hairpocket.
(Diagrams I – J)
4. After cleaning,
replace the Foil Assembly.
(Diagram L)
L
J
H
I
KP
N
O
Q
When your rechargeable shaver reach-
es the end of its useful life, the batter-
ies must be removed from the shaver
and recycled or disposed of properly in
accordance with your state and local
requirements. If this is not required by
law, you may elect to dispose of the
shaver with the batteries.
CAUTION! Do not put in fire or muti-
late your batteries when disposing
as they may burst and release toxic
materials. Do not short circuit as it
may cause burns. Dispose of properly
in accordance with your local and
state requirements.
To Remove the Rechargeable Battery:
1. Remove the Cutter Assembly and
cutters.
Battery Removal
2. Insert small flathead screwdriver
into small opening at the top of the
panel located on left side of shaver
with on/off button facing toward
you.
3. Loosen and remove the six screws
with a Phillips screwdriver, and
remove the rear housing.
4. Cut the lead wires, remove the
four screws with a Phillips head
screwdriver, and remove the battery
cover.
5. Take out the Ni-MH battery, and cut
the lead wires while taking care
not to short-circuit the (+) and (-)
terminals.
6. Dispose battery property in
accordance with your state and
local requirements.
Maintain your shaver’s peak
performance! Keep your shaver
performing like new!
■ Because your satisfaction is
important to us, we make it simple
for you to keep your new shaver
performing at its peak.
■ Remington makes this easy!
Two easy ways to order!
1. Call!
800-392-6544
2. Order Online at
www.RemingtonProducts.com
Warranty
Product Registration
By registering your new Remington
product you will receive these
important benefits:
■ Proof of ownership
■ Product protection
■ Product registration
■ Special offer
Register online at:
www.RemingtonProducts.com
Limited Two-Year Warranty
Spectrum Brands, Inc. warrants this
product against any defects that are
due to faulty material or workmanship
for a two-year period from the original
date of consumer purchase. This
warranty does not include damage to
the product resulting from accident or
misuse. If the product should become
defective within the warranty period,
we will replace it free of charge.
Return your product and sales receipt
with your name, address and day time
phone number to: Remington Returns
Center, 507 Stokely Dr., P.O. Box 1,
Deforest, WI 53532. For more infor-
mation call 800-736-4648 in the US
or 800-268-0425 in Canada.
Warranty excludes:
■ Foils and cutters
KEEP ORIGINAL SALES RECEIPT
AS PROOF OF PURCHASE FOR
WARRANTY PURPOSES.
This warranty does not cover
products damaged by the following:
■ Accident, misuse, abuse or
alteration of the product
■ Servicing by unauthorized persons
■ Use with unauthorized accessories
■ Connecting it to incorrect current
and voltage
■ Wrapping cord around appliance
causing premature wear & breakage
■ Any other conditions beyond our
control
SPECTRUM BRANDS, INC.
SHALL NOT BE RESPONSIBLE
FOR ANY INCIDENTAL, SPECIAL
OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS
PRODUCT. ALL IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO
IMPLIED WARRANTIES OF FITNESS
AND MERCHANTABILITY, ARE LIMITED
IN DURATION TO TWO YEARS FROM
DATE OF ORIGINAL PURCHASE.
This warranty gives you specific legal
rights and you may also have other
rights which vary from state to state
or province to province. Some states
do not allow the exclusion or limita-
tion of incidental, special or conse-
quential damages.
How To Order Shaver Accessories
Please refer to the shaver compari-
son and features chart near the
front of this manual that lists the
correct replacement part number
for your shaver.
It is very important to replace your
screens and cutters when necessary
to ensure a close, comfortable shave
without irritation. We recommend they
be replaced every 6 months. Here are
some signs of head and cutter wear,
indicating that replacement
is needed:
■ Irritation: As the screens get
excessively worn you may
experience some skin irritation.
This would be especially noticeable
when you apply moisturizing lotion.
■ Pulling: When the cutters wear you
may feel a sense of pulling and a
loss of closeness when you shave.
This is an indication that it is time
to replace your screens and cutters.
Performance Guarantee
Spectrum Brands, Inc.
Money-back Offer
If within 30 days after you have
purchased your Remington®branded
product, you are not satisfied and
would like a refund, return it with
the sales slip indicating purchase
price and date of purchase to the
retailer from whom it was purchased.
Spectrum Brands, Inc. will reimburse
all retailers who accept the product
within 30 days from the date of pur-
chase. If you have any questions con-
cerning the money-back guarantee,
please call 800-736-4648 in the US
or 800-268-0425 in Canada.
Questions or comments:
Call 800-736-4648 in the US or
800-268-0425 in Canada or visit
www.RemingtonProducts.com
Dist. by: Spectrum Brands, Inc.,
Madison, WI 53711
Dist. by: Spectrum Brands Canada, Inc.
4180 Sladeview Cresent
Mississauga, ON L5L 0A1
® Registered Trademark of
ROVCAL, Inc. a subsidiary of
Spectrum Brands, Inc.
© 2012 ROVCAL, Inc. 5/12
Job #CS43002_RevA
Manufactured to Remington's
specifications in the PRC.
T22-34456
Shaver: 100-240 VAC, 50-60 Hz
Contains
listed adaptor
IMPORTANT SAFETY
INSTRUCTIONS - SAvE
ThESE INSTRUCTIONS
DANGER - TO REDUCE ThE
RISK OF FIRE OR ELECTRIC
ShOCK, CAREFULLY FOLLOW
ThESE INSTRUCTIONS
For connection to a supply not in the U.S.A., use an attachment plug adapter of the
proper configuration for the power outlet.
Power Adaptor
M