RemoteLock OpenEdge 800 Series Manual

Do this first:
Hardware Installation
1
800 SERIES
HEAVY DUTY
COMMERCIAL LEVER

Need some help? Here’s what you’ll need:
Visit us online.
support.remotelock.com
We’re here to help.
1 [phone]
[e-mail]
Four AA Batteries
Phillips Screwdriver
Power Drill
2-⅛” Hole Saw (optional if the door is not preconfigured
with this hole)
1” (25mm) Drill Bit (for the middle hole and edge
borehole if the door is not preconfigured)
⅜” (10mm) Drill Bit
Measuring Tape
Adhesive Tape

Install your lock.
Use this Hardware Installation
Guide to get your lock installed.
Get connected.
Use the Connection Guide to get
your lock online and registered.
Take control.
Now your lock is fully functional and
can be managed from anywhere.
11
22
33
You are here. Find more help online.
For additional installation instructions and
troubleshooting tips, be sure to visit our online
support site: support.remotelock.com.

Drilling new holes?
Most doors will have an existing hole drilled for a
lever installation. If your door needs to be drilled,
you’ll need to drill a 2 ⅛“ (54mm) face bore hole for
the lockset on the face of the door, as well as a 1”
edge bore hole for the latch on the edge of the door.
Let’s get
started.
First things first, let’s get
your new lock installed. Face Bore Hole
Edge Bore Hole
for Latch

STEP 1
Position the template.
Crease the template along Door Edge dotted line. Place
the template on the door and position with the existing
face bore hole.
Once the template is aligned, tape it to the door.
Exterior of Door
View the template from
the other side of the
boring hole to make
sure it’s aligned.
Quick Tip

STEP 2
Mark carefully and drill.
Use a thumbtack or sharp object to mark the center of
each hole you will drill. Mark the seven holes on the
exterior of the door. Then apply the template to the
other side of the door and mark the holes from this
side as well.
Exterior of Door
Interior of Door

Remove the template.
Make sure the markings are aligned precisely from one
side of the door to the other and double check all the
measurements and markings before drilling.
Use a chisel to create the shallow notches on each side
of the face bore hole.
Align the drill bit over your mark and hold the door
steady. Keep the drill level and straight. Drill the ⅜”
holes halfway through on the first side. Then drill the
remaining half from the other side of the door. This
prevents damage to the door and improves accuracy. DRILL HALFWAY THROUGH
ON EACH SIDE
⅜” (10mm) Drill Bit

Repeat these steps for the 1” middle hole.
Drill the 1” holes halfway through on the first side.
Then drill the remaining half from the other side
of the door.
1” (25mm) Drill Bit

The lock body comes prepped for a 1 ¾” thick door.
Ensure the setup is correct by removing the lock body
from the lock housing and inserting the lock body in the
face bore hole.
View the slide clip through the edge bore hole. Turn
exterior rose to adjust center line of lock body to match
the centerline of the door.
Remove the lock body after positioning and continue to
STEP 4.
STEP 3
Conrm door thickness
and adjust.
Remove Lock Place on Door
ENSURE ALIGNMENT

Install the latch using the screws provided, with the
bevel towards the door frame.
STEP 4
Install latch.
Make sure the latch plate lays flush with the door. If the latch plate is
not flush with the door, draw an outline around the faceplate edge
and chisel a rebate to allow the latch to lay flush with the door edge.
Quick Tip
X2
Exterior of Door

STEP 5
Conrm lock handing.
PLEASE NOTE:
Locks are supplied right handed. To reverse lock
handing, perform the following steps. If handing is
correct, move onto STEP 6.
To Reverse Outside Handle:
A. Turn key clockwise to vertical position.
B. Depress the lever catch with the pin wrench provided.
C. Pull off lever.
A
B
C

D. Remove the lever retractor spindle from the outside
housing.
E. Rotate 180 degrees.
F. Place back into the housing.
G. Replace the lever back onto the lock in the left-hand
position. Ensure key is in the vertical position and
push lever on fully until it “clicks” into place.
Turn key counter-clockwise and remove.
D E
GF
You will see your lock’s serial and model number on the RemoteLock
sticker on the back of the lock. Write it down or take a picture for
your records. This number is needed during online registration after
installation. You will also find this sticker on the lock’s box.
Quick Tip

To Reverse Inside Handle:
A. Depress the lever catch with the pin wrench
provided.
B. Pull off lever.
C. Remove the lever spring cage from the inside
housing, rotate 180 degrees, then place back into the
housing.
D. Position the lever in the left-hand position and slide
onto lever spring cage. Push lever on fully until the
lever “clicks” into place.
B
D
A
C

STEP 6
Place the outside lock.
Slide the lock body into place on the outside lock
assembly, ensuring that the slide clip of the retractor is
facing the latch side of the door.
Install the outside body and lock assembly. Take care to
thread the upper three cables through the cable hole in the
door. Also insert the motor cable through the face bore hole.
As the outside body is put in place, ensure that the prongs
of the latch fit between the slide clip of the retractor. To
do this, push in the latch slightly with your thumb.
If the prongs are not properly positioned, the latch could
bind or be damaged resulting in improper function.
RETRACTOR
SLIDE CLIP
LATCH PRONGS
Exterior of Door
Interior of Door

STEP 7
Install interior rose
mounting plate.
Place the interior rose mounting plate over the
spindle, ensuring that the cable hooks are on top
and the motor cable passes through one side of the
center hole.
The interior rose will be secured in a later step with
screws.
Interior of Door

STEP 8
Install battery mounting
plate.
Place the battery mounting plate against the interior of
the door, passing power cables and antenna through the
hole in the center of the plate.
Pass two inner mounting bolts through the top of the
mounting plate and door and tighten into the outside lock.
Interior of Door

STEP 9
Connect wires.
Connect the red outside cable to the red battery plug.
Also connect the black outside cable to the black motor plug.
Push any excess cable back into the hole through the door.
IMPORTANT: Make sure cables are not pinched.
Utilize the cable hooks as shown.
!

STEP 10
Install interior lock.
Remove the battery cover from the interior lock body if
still secured.
Pass the antenna cable through the battery cover
opening and position the interior lock body over the
lever retractor spindle, ensuring it fits flush on the door.
Secure the interior lock with two through mounting bolts
above and below the lever and two short mounting bolts
at the top of the lock.
Interior of Door

STEP 11
Install batteries and
battery cover.
Install four AA batteries into the battery compartment.
Plug the antenna cable into the antenna plug on the
battery cover. Push the plug firmly until you feel and hear
it click into place.
Fit battery cover into place and secure with screw
provided.

STEP 12
Operational Check
Before closing the door, check the operation of the lock.
Depress the internal lever to retract the latch. Ensure that
the latch retracts, then fully springs back into place.
Test the outside of the lock by entering the default code
1234#. You should see the keypad lights flash green.
Depress the handle to ensure the latch retracts.
PLEASE NOTE:
1234 will be disabled once an additional code is added
to the lock. Also, entering #after the code will not be
required after the lock is connected to Wi-Fi.
Exterior of DoorExterior of Door