Renaissance Fireplaces LINEAR 50 SP User manual

RL50SP-OW – 2017-08
RENAISSANCE
LINEAR 50 SP
Keep these instructions for future use.

GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 2
Dear Customer,
The Renaissance LINEAR 50 SP is a member of the Renaissance Fireplaces family of ultra-high-end fireplaces. The
LINEAR 50 SP is unique in its design. The 50" wide opening provides an enormous linear space to watch the fire. It
combines technology with elegance, allowing you to enjoy an open fire in a modern fashion.
We have designed your new fireplace to be easy to install, operate and maintain. It is in your best interest to become
familiar with it.
Congratulations on your choice of the LINEAR 50 SP. We at Renaissance Fireplaces are confident that you have
purchased a fireplace that burns beautifully, without compromise.
Sincerely,
Renaissance FireplacesTM Team
August 2017

GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 3
TABLE OF CONTENTS
GETTING STARTED: WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 4
IMPORTANT SAFETY AND OPERATION PRECAUTIONS 4
Do's and Don'ts 4
Avoiding Excessive Temperatures 5
FEATURES 6
Unique Decorative Fireplace 6
Options 6
PROPER FUEL 7
What to Burn at All Times 7
What to Burn Occasionally and Carefully 7
What Never to Burn 7
FIRST FIRES 8
OPERATING THE FIREPLACE 8
BEFORE FIREBUILDING 8
Glass Door Operation 8
Outside Air Control 8
Chimney Damper 9
BUILDING THE FIRE 9
CONTROLLING THE FIRE 10
REFUELING 10
MAINTENANCE 11
ROUTINE TASKS 11
Disposal of Ashes 11
General Cleaning 11
Paint 11
Glass Cleaning 11
GASKETS 12
ADJUSTING THE DOOR LATCH 12
CHIMNEY CLEANING 12
REPLACEMENT PARTS 13
LISTING LABEL 13
WARRANTY 14
We strongly recommend that our
products be installed and serviced
by professionals who are certified
by the National Fireplace Institute
in the U.S. or by Wood Energy
Technology Transfer Inc. in
Canada.

GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 4
GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING
IMPORTANT SAFETY AND OPERATION PRECAUTIONS
DO'S AND DON'TS
If this fireplace is not properly installed, a house fire could result. For your safety the fireplace should be installed by a
professional following the installation directions. The local authority having jurisdiction (such as municipal building department
or fire department) should be contacted regarding restrictions and installation requirements, and the need to obtain a permit.
To ANYONE using this fireplace: these DO's and DON’Ts are for your safety and for the durability of the unit. Detailed explanations follow in
the manual.
1. DO read this owner's manual before lighting your first fire.
2. DO keep these instructions, as well as the Installer’s Manual, for future use.
3. DO burn dry, split, seasoned wood fuel.
4. DO operate the fireplace with the glass door either fully closed or fully open. If the glass door is left partly open, it will increase the
burn rate and permanently damage the fireplace.
5. DO keep all combustible materials (furniture, firewood, etc.) at least 4' away from the front of the fireplace.
6. DO have the chimney inspected for creosote buildup, at least on an annual basis, and have it professionally cleaned as needed
to prevent a chimney fire. See complete information on the following page and in the Maintenance section.
7. DO NOT slam the fireplace door in opening and closing it, to avoid glass breakage.
8. DO NOT use the fireplace with the door closed if the glass is cracked or broken. Replace the glass before using the glass door again.
9. DO NOT ever use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid or similar liquids to start or freshen up a fire. Keep
all such liquids well away from the fireplace while it is in use.
10.DO NOT over fire the fireplace. Burn a maximum of 4-5 medium logs (5" diameter) or 3 large logs (6" diameter), of an overall length
equivalent to 24” pieces, at a time. See complete warning on page 5.
11.DO NOT use a fireplace grate or other products not specified for use with this fireplace.
12.DO NOT step or put legs of a step ladder on any of the black lintels surrounding the glasses.

GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 5
AVOIDING EXCESSIVE TEMPERATURES
Over Firing
WARNING: OVER FIRING THE RENAISSANCE LINEAR 50 SP WILL CAUSE DURABILITY PROBLEMS.
THE RENAISSANCE IS CAPABLE OF BURNING CLEANLY PRIMARILY BECAUSE IT HAS BEEN ENGINEERED TO QUICKLY
BURN VERY HOT. THIS RESULTS IN A BEAUTIFUL, CLEAN FIRE BUT CAN CAUSE DURABILITY PROBLEMS IF THE UNIT
IS REGULARLY OVERLOADED AND/OR OPERATED CONTINUOUSLY WITH EXCESSIVE LARGE WOOD LOADS. THE
RENAISSANCE IS PRIMARILY A DECORATIVE APPLIANCE AND ACCORDINGLY LESS EFFICIENT THAN A WOOD
BURNING STOVE SO THERE IS NO BENEFIT TO BURNING LARGER WOOD LOADS.
THE FOLLOWING GUIDELINES WILL ENSURE YOUR FIREPLACE BURNS BEAUTIFULLY WHILE MAINTAINING ITS
DURABILITY:
APPROXIMATE MAXIMUM LOG SIZE: 6" IN DIAMETER.
APPROXIMATE MAXIMUM LOAD: NO MORE THAN THE EQUIVALENT OF 3 LOGS 24" IN LENGTH.
THIS WOOD LOAD IS MORE THAN SUFFICIENT TO FILL THE FIREBOX COMPLETELY WITH FLAMES AND PROVIDE A
LARGE AMOUNT OF RADIANT HEAT.
THE RENAISSANCE LINEAR 50 SP WILL BURN WITH LARGE HIGH FLAMES REGARDLESS OF HOW THE WOOD IS
PLACED IN THE UNIT. STACKING THE WOOD TIPI-STYLE AGAINST THE BACK OF THE FIREPLACE IS ACCEPTABLE
BUT CAN COSMETICALLY DAMAGE THE FIREBOX REFRACTORY BRICKS IF YOU’RE NOT CAREFUL PLACING THE LOGS.
IF ANY OF THE FOLLOWING SIGNS APPEAR IN YOUR FIREPLACE THEN YOU ARE OVER FIRING:
THE REFRACTORY BRICKS ARE CRACKING AND DETERIORATING QUICKLY
THE DOOR CHANNEL IS WARPED
Creosote: Formation and Removal
When wood is burned slowly, it produces tar and other organic vapors which combine with the expelled moisture from the wood to form creosote.
The creosote vapors can condense in the relatively cool chimney of a slow burning fire. When ignited, this creosote makes an extremely hot fire
in the chimney. The chimney should be inspected periodically during the heating season to see if a creosote build-up has occurred. If a significant
layer of creosote has accumulated (¼" or more), it should be removed to reduce the risk of chimney fire.

GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 6
FEATURES
UNIQUE DECORATIVE FIREPLACE
The LINEAR 50 SP fireplace is a decorative fireplace that provides a magnificent view of the fire. It is defined as a fireplace (primarily for
aesthetics) under the 2015 EPA (United States Environmental Protection Agency) regulation since it offers more than 500 square inches of pure
fire viewing (682 square inches are visible). Small amounts of firewood can fill the firebox with large, beautiful flames in this exceptional
fireplace.
OPTIONS
The LINEAR 50 SP can be installed with two different chimney systems:
10" RIS: you will need to use the EO-10SPAP to be able to connect the 10" RIS chimney to your fireplace;
8" EXCEL: you will need to use the EO-08SPAP to be able to connect the 8" EXCEL chimney to your fireplace.
Be aware that the requirements for minimum chimney height are not the same for the two chimney systems. See the installation manual for
more information and make sure you plan accordingly.
The Heat Redistribution System (HRS) is mandatory, and requires the installation of air intakes and outlets to allow air to circulate through the
fireplace. Included with the fireplace are two air intake grills, two hot air outlets and two insulated flexible ducts with the outlet grill adapters.
We also offer different styles of grills in option:
If you would prefer one long linear grill for the hot air outlet (above the fireplace) instead of two rectangular outlet grills, we offer the Long
Linear Outlet Grill (EO-LLG-OUT). Please refer to the installation instructions of the option for installation restrictions compared to the hot
air outlet grills provided.
You can also change the two rectangular intake grills for one Long Linear Intake Grill (EO-LLG-IN). Please refer to the installation instructions
of the option for installation restrictions compared to the rectangular grills provided.
Installations in an 8' ceiling require specific Air Outlet Grills to ensure adequate heat is vented from the fireplace. The Square Grills for 8'
Ceiling (EO-SG) includes two 13" square grills and two outlet grill adapters that are required when the ceiling is only at 8'. Please refer to
the installation instructions of the option for installation restrictions compared to the rectangular grills provided.
Vented gas logs sets are permitted, unvented gas logs are not. Go online to the Renaissance web site: www.renaissancefireplaces.com for more
information.
WARNING: THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS LOG SET. TO REDUCE RISK OF FIRE OR INJURY,
DO NOT INSTALL AN UNVENTED GAS LOG SET INTO THIS FIREPLACE. DO NOT INSTALL A GAS LIGHTER BECAUSE
THE HEAT PRODUCED BY THE FIREPLACE MAY PERMANENTLY DAMAGE THE GAS LIGHTER

GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING 7
PROPER FUEL
It’s true of all combustion appliances: the better the fuel, the better the burn. Let’s look now at the characteristics of good fuel, so that you
have the right information to provide your LINEAR 50 SP with the fuel that will make for easier and faster starting, cleaner and more beautiful
burning, and reduced maintenance.
WHAT TO BURN AT ALL TIMES
We recommend always burning your fireplace with split, dry, seasoned wood logs. Your fireplace will not burn cleanly or efficiently unless the
wood is dry and well-seasoned. That means wood that has been cut, split, stored in a stack that is covered on top, but open on the sides for
air flow for at least 6 months, but preferably for a year or two.
There are some simple indicators that wood is reasonably well-seasoned: loose or fallen bark, checking and splitting of the log ends, weight
relative to known dry wood, ease in splitting, and how the wood burns (catches quickly and does not sizzle or drip water. But the best way to
know that your wood is really well-seasoned is with a moisture meter. This is a simple gauge that measures moisture content. Exact accuracy
is less important than establishing a benchmark. With an inexpensive meter, you can find a range (usually 20-25% or less) that gives you a
way to have and meet an effective, reasonable standard for your firewood.
You can burn any well-seasoned species of wood. Softwoods dry quickly, start easily, and offer quick, bright burns. Hardwoods generally take
longer to season and burn longer.
WHAT TO BURN OCCASIONALLY AND CAREFULLY
Do not use construction scraps (e.g. 2x4 or plywood scraps) as your only supply of fuel as you can overheat and seriously damage the fireplace.
If you use densified wood logs, do not use more than two at a time and only with the firescreen closed. If you use more than two at a time,
you will over fire the fireplace. Do not poke or stir the logs while they are burning.
If you use wax fuel logs (e.g. Duraflame), do not use more than one wax fuel log at a time and only with the firescreen closed. Using them with
a closed door will lead to a dirty glass. Furthermore, if you use more than one at a time, you will over fire the fireplace. Do not poke or stir the
log while it is burning.
Use only firelogs that have been evaluated for fireplace use. In Canada, they should meet the requirements of ULC/ORD-C127-M1990. Refer to
the firelog warnings and caution markings prior to use.
WARNING: BURN DRY WOOD ONLY.
DO NOT BURN DRIFTWOOD, TREATED WOOD, COAL, GARBAGE, OR PLASTIC.
WHAT NEVER TO BURN
Never use flammable liquids such as gasoline, kerosene, charcoal lighter fluids to start or refresh a fire in the LINEAR 50 SP.
Never burn driftwood, treated wood, coal, garbage, or plastic.

OPERATING THE FIREPLACE 8
FIRST FIRES
Be aware that there is a possibility of minor smoke and odor emitted into the house from oils and paint curing during the first few firings of the
new fireplace. You may want to schedule first burns when doors and windows of the house can be opened if needed.
The refractory bricks will accumulate moisture after extended periods without burning. The first fire will burn off this excess moisture and may
make it more difficult to light.
OPERATING THE FIREPLACE
BEFORE FIREBUILDING
GLASS DOOR OPERATION
To open the glass door, simply grab the wood handle at the top right corner of the door and
pivot it to the left to unlock the latch (see Figure 1). Then pull to open the door. There is a
magnet at the bottom of the glass door. When the door is unlatched, you must pull hard
enough to disengage it from the magnet.
The latch must be in the locked position during a fire for safety reasons.
To minimize the risk of injuries or burns, do not touch any of the door parts other
than the wooden knob with your bare hands while the fireplace is hot because they
may be hot enough to cause serious burns.
OUTSIDE AIR CONTROL
The LINEAR 50 SP is designed to use outside air for combustion. The control for the outside
air is located inside the firebox, in front of the left ash step refractory brick (see Figure 3).
Since it is inside the firebox, we recommend that you open the outside air before lighting a
fire, and wait until the firebox cools down to close it.
To minimize the risk of injuries or burns, do not touch the outside air control and
the surrounding parts with your bare hands while the fireplace is hot. They will be
hot enough to cause serious burns.
When the outside air control is facing to the right, the outside air damper is open. When it is facing towards the back, the outside air damper is
closed. Use a gloved hand to adjust the air control when the fireplace is hot.
Figure 1 Door Latch & Magnet

OPERATING THE FIREPLACE 9
To close the outside air, gently lift the outside air lever and then turn counterclockwise to the
closed position. A spring will assist and keep it closed. Top open the outside air, turn the outside
air control lever to the right and then push it down to lock the damper in open position.
Even though the fireplace can be operated with the outside air damper closed, we recommend
always using outside air for combustion when burning the fireplace. In some cases, this fresh
air will also help compensate for negative pressure problems within the house (for example,
when strong kitchen or bath fans compete with and reduce chimney draft in a tightly
constructed house); however, it will not prevent the fireplace from smoking in a severely
depressurized house.
This control should, however, be closed when the fireplace isn’t burning to prevent cold air
infiltration. It is sealed with a gasket.
CHIMNEY DAMPER
The LINEAR 50 SP is equipped with a chimney damper that is located in the flue at the top of
the fireplace. This chimney damper should only be used in either fully open or fully closed
position. The chain for the chimney damper is inside the firebox at the front, just above the
opening.
To close the chimney damper, pull the chain down and secure it in the slot to close the damper
(see Figure 2). When closed, the damper virtually eliminates warm air flow up the chimney
while preventing cold air from entering from outside. The damper is counter-balanced and will open
by itself when you un-hook the damper chain. The hook portion of the damper allows the chain to be
hung so that it remains out of view.
BUILDING THE FIRE
Always start by opening the chimney damper and the outside air.
There are many ways to arrange your firewood to build a fire in your LINEAR 50 SP. Always build and
maintain the fire well behind the ash step refractory bricks, never against or close to the glass door.
In all cases, you want to start with a number of pieces of easily lit material, such as newspaper. Place
pieces of crumpled or loosely knotted paper in the area where you will be placing the kindling and
firewood. Then add a generous layer of kindling over the paper, placed with spaces between the
pieces for air flow. Finally, stack 2-3 small-medium size logs over the kindling so that they are close
or touching one another, but have small spaces between them for air flow. Then light the paper in a
number of places and close the door. Once the fire is established, you can add more wood. The glass
door should always be closed when the fire is burning.
Never use flammable liquids to start or refresh the fire.
Figure 2 Chimney Damper Chain
Figure 3 Outside Air Control Location

OPERATING THE FIREPLACE 10
CONTROLLING THE FIRE
The LINEAR 50 SP fireplace is designed to provide warm radiant heat. Although it does not come with a draft control, you will find that you can
control the intensity of the fire and the quantity of flames quite well by varying the size and placement of the logs.
Make sure to always lock the door when a fire is burning.
For a small fire, load 3 to 4 small logs (3" diameter).
For a large fire, load 4 to 5 small-medium logs (5" diameter).
Even though the firebox is quite big, you will soon discover that it is unnecessary to load a lot of wood to get magnificent flames. Be careful not
to overload your fireplace, you will risk over firing your fireplace and overheating the room in which the fireplace is located. You will get greater
satisfaction looking at a couple of small logs burning.
WARNING: PLEASE READ THE WARNING RELATED TO OVERFIRING THE FIREPLACE IN THE "GETTING STARTED:
WHAT TO KNOW AND DO BEFORE THE FIRST FIRING - IMPORTANT SAFETY AND OPERATION PRECAUTIONS"
SECTION OF THIS MANUAL.
REFUELING
As the fire burns down and you want to add more wood, begin by having the firewood you intend to add in a convenient location near the
fireplace. Select an appropriate fireplace tool to arrange remaining burning wood or to spread hot coals where you intend to place the new fuel.
It is always recommended to use heavy fireplace gloves for the refueling process.
The door should be opened slowly to keep smoke from spilling into your room. If you have a problem with smoke spillage, check
to see that all kitchen and bathroom fans have been shut off. They can cause negative pressure in the house which pulls smoke
out of the fireplace.

MAINTENANCE 11
MAINTENANCE
ROUTINE TASKS
DISPOSAL OF ASHES
Remove the ashes before they become too deep, i.e., before you have a spillage problem over the ash step refractory bricks.
The ashes should be placed in a metal container with a tight-fitting lid. Any hot coals embedded in the ashes can stay very hot very long.
Therefore the closed container of ashes should be placed on a non-combustible floor or on the ground, well away from all combustible materials
pending final disposal. If the ashes are disposed of by burial, or otherwise locally dispersed, they should be retained in the closed container
until all cinders are thoroughly extinguished.
GENERAL CLEANING
Any black painted portion of the fireplace can be cleaned with a soft damp cloth. Use a mild detergent and water. Do not use abrasive cleaners.
PAINT
You can touch up the metal areas of the face of the LINEAR 50 SP with Stove Bright Metallic Black high temperature paint which is available at
most fireplace dealers. Follow the directions outlined on the spray can. DO NOT attempt to paint the fireplace while it is still warm. Keep the
spray can away from any source of heat or open flame. Ensure that there is adequate ventilation in the room from the time you start painting
until the paint is dry. Stove Bright is available in a wide range of colors if you want to change the color of your fireplace.
We recommend that you take the time to protect or remove any items that you do not want to paint such as the door glass, the materials
surrounding the fireplace, the hearth extension (the non-combustible finishing material on the floor in front of the fireplace), etc.
GLASS CLEANING
Depending on how you burn your LINEAR 50 SP, temperatures may not always be hot enough to keep the glass perfectly clean. Having a good
hot fire regularly usually cleans off most of the deposits that have accumulated. Remember: the dryer the wood and the hotter the fire, the
cleaner the glass. A word of caution: although heat will not break the glass, impact can. Be careful not to hit the glass.
WARNING: NEVER CLEAN THE GLASS WHILE IT IS HOT; A SERIOUS BURN CAN RESULT. NEVER CLEAN THE GLASS WITH AN
ABRASIVE CLEANER. USE ONLY A CLEANER RECOMMENDED BY YOUR DEALER. THERE ARE A NUMBER OF EXCELLENT
WOOD STOVE GLASS CLEANERS AVAILABLE WHICH ARE FAR SUPERIOR TO REGULAR GLASS AND OVEN CLEANERS.

MAINTENANCE 12
GASKETS
The design of the fireplace requires many gaskets to get just the right amount of combustion air
into the firebox and keep all three glasses clean (see Figure 4).
1. There is a round fiberglass gasket on the back of the top of the door held in place by clips in
the door frame. There is also a small screw holding the extremity close to the hinge.
This gasket will need to be removed if the door glass needs to be changed. If the gasket is
still in good condition, it can be reinstalled after changing the door glass.
2. There is a flat fiberglass gasket wrapped around the top of the glass in the door. If you remove
or change the door glass, this gasket will need to be changed as well.
3. There are high temperature silicone gaskets wrapped around the top and bottom of each side
glasses as well as the bottom of the door glass. If you ever need to remove or change any
of the glasses, this gasket will need to be changed as well.
Any of these gaskets may need to be changed at one point in time depending on how careful you
are at not allowing the fire in front of the ash step refractory bricks. If at any point, you see a
change in the flame pattern (flames coming close to the glass, burning more on one side, or
simply not burning nicely), you may need to change one of the gaskets.
There is no gasket at the bottom of the glass door.
ADJUSTING THE DOOR LATCH
The door latch should close with enough resistance to keep it latched, but not so much resistance
that it is difficult to close. The latch plate can adjust the tightness of the door latch. It is located
just below the top lintel behind the door latch. Open the door to access the latch plate (see Figure
5).
To tighten the latch: using a small hammer, gently tap on the extremity of the latch plate to bring
it closer to the facing of the fireplace.
To loosen the latch: using a big flat screw driver, slip the tip behind the extremity of the latch
plate to pull it away from the facing of the fireplace.
CHIMNEY CLEANING
A fireplace as clean burning as the LINEAR 50 SP does not produce a lot of creosote, but the
chimney should nevertheless be inspected for creosote buildup after a couple of months of using it. This will allow you to visualize the amount
Figure 4 Door Gaskets
Figure 5 Latch Plate Adjustment

LISTING LABEL 13
of creosote that is accumulating and adjust the frequency of checking the chimney accordingly. At least an annual inspection is recommended.
A buildup of ¼" or more calls for cleaning by a chimney professional. Depending on how you burn your LINEAR 50 SP, the chimney may need
cleaning every year or every other year.
REPLACEMENT PARTS
A complete list of replacement parts is available on our web site: www.renaissancefireplaces.com.
LISTING LABEL
The listing label has been placed on the bottom face of the bottom lintel. If you are planning on covering the facing of the fireplace with thick
finishing materials, take the time to take note of the fireplace serial number for future reference.

WARRANTY 14
WARRANTY
30 YEAR LIMITED WARRANTY
FOR RENAISSANCE FIREPLACESTM
All Renaissance Fireplaces™ models are warranted against defects in material and workmanship for a period of 30 years, subject to the
following conditions:
During the first year Renaissance Fireplaces™ will repair or replace, at our option, any parts which upon examination by an authorized
Renaissance Fireplaces™ representative, are found to be defective, except the parts listed in the EXCLUSIONS portion of this warranty.
Renaissance Fireplaces™ will also pay reasonable labor costs for the repair work.
During the second through fifth years Renaissance Fireplaces™ will repair or replace, at our option, any parts which upon examination by an
authorized Renaissance Fireplaces™ representative, are found to be defective, except the parts listed in the EXCLUSIONS portion of this
warranty. Renaissance Fireplaces™ shall not be responsible for any labor costs associated with this repair work.
During the sixth through thirtieth years Renaissance Fireplaces™ will provide replacement parts, if available, at 50% of the published retail
price, except for the parts listed in the EXCLUSIONS portion of this warranty. Renaissance Fireplaces™ shall not be responsible for any labor
costs associated with this repair work.
EXCLUSIONS:
Glass.
Damage due to normal wear and tear, such as paint discoloration, worn gaskets, eroded or cracked rigid insulation panels or firebox lining
components.
Repairs or replacements necessitated by vandalism, neglect, abuse, over-firing, improper fuel or fuel loads, or failure to adequately service
the unit, as stated in the owner's manual.
Repairs or replacements (particularly charges for travel and labor) not authorized by Renaissance Fireplaces™ in advance.
LIMITATIONS:
All items found to be defective will be replaced or repaired upon return of the defective part to an authorized Renaissance Fireplaces™
dealer. Renaissance Fireplaces™ will not be responsible for freight costs related to shipping replacement parts.
Any complete fireplace, or part thereof, that is replaced or serviced under this warranty, will be warranted for a period not exceeding the
remaining term of the original warranty.
This warranty is not transferable.
This warranty does not apply to damage to the appliance while in transit.

WARRANTY 15
This warranty does not apply if the installation does not conform to the installation requirements in the installation and owner's manuals.
Renaissance Fireplaces™ is free of liability for any damages caused by the appliance, as well as material and labor charges incurred in
the removal or re-installation of any Renaissance Fireplaces™ fireplace under this warranty. Incidental or consequential damages are not
covered by this warranty.
The remedies set forth herein are exclusive, and the liability of the seller shall not exceed the price of the fireplace or part thereof upon
which the liability is based.
This warranty is expressly in lieu of all other warranties expressed or implied, including the warranties of merchantability and fitness for use
and all other obligations or liabilities on the part of Renaissance Fireplaces™.