Renaissance Fireplaces RUMFORD 1000 User manual

RRR1000B-INAN - 2020-04
RENAISSANCE RUMFORDTM 1000
INSTALLATION MANUAL
We recommend our products be installed and serviced by certified U.S. National
Fireplace Institute or Canadian Wood Energy Technology Transfer Inc. professionals
only.
Keep this manual for future reference.

2
NOTE TO THE INSTALLER
Dear Installer,
The Renaissance RUMFORDTM 1000 Fireplace is the world’s first certified clean burning
open fireplace. It combines technology with elegance, allowing you to enjoy an open
fire without compromising environmental quality.
Our engineers designed the Renaissance RUMFORDTM 1000 to be easy to install,
operate and maintain. This manual includes vital fireplace and chimney system
planning, preparation, and installation details. Read this manual prior to starting the
installation to ensure all requirements are met. For operation and maintenance
guidelines, please refer to the Owner's Manual, included with the Fireplace.
Make sure to give both manuals, installation and owner's, to the homeowner or to
leave them in a visible place.
Our team holds personal safety and protection with the highest regard, and we pride
ourselves with the quality of our work. We welcome comments and feedback
concerning the installation of the Renaissance RUMFORDTM 1000. Contact us by phone
or email.
Sincerely,
The Renaissance FireplacesTM Team
Industrial Chimney Company Inc.
400 J.-F. Kennedy, St-Jerome,
Quebec, Canada, J7Y 4B7
Telephone: [phone]
Email: techn[email protected]om
www.icc-rsf.com

3
TABLE OF CONTENTS
RENAISSANCE RUMFORDTM 1000 LISTING LABEL 4
IMPORTANT INSTALLATION SAFETY PRECAUTIONS 5
YES! WHAT TO DO 5
NO! WHAT NOT TO DO 5
COMBUSTIBLE VS NON-COMBUSTIBLE MATERIAL 5
PLANNING THE INSTALLATION 6
RECOMMENDATIONS 6
CHOOSING A LOCATION AND RESTRICTIONS 6
INSTALLATION OVERVIEW 7
GENERAL SPECIFICATIONS 8
FIREPLACE SPECIFICATIONS 9
FRAMING OVERVIEW 10
CHIMNEY OVERVIEW 11
FIREPLACE INSTALLATION 12
INCLUDED WITH THE RENAISSANCE RUMFORDTM 1000 12
MOVING THE RUMFORD 1000 14
ENGAGING THE GUILLOTINE SYSTEM 15
Counterweights' Installation 15
Firescreen 17
Unlocking the Glass Door 17
MANDATORY INSTALLATIONS 18
MANDATORY -SPARK GUARD 18
MANDATORY –SECURING THE FIREPLACE 18
MANDATORY -FIREBOX LINING OPTIONS (ONE CHOICE REQUIRED) 18
MANDATORY –ANTI-TIP BRACKETS 19
MANDATORY CLEARANCES 20
FIREPLACE CLEARANCES 20
CEILING HEIGHT REQUIREMENTS 20
HEARTH EXTENSION REQUIREMENTS 22
OUTSIDE AIR INTAKE 25
CHIMNEY 26
CHIMNEY REQUIREMENTS 26
OFFSETTING THE CHIMNEY 27
THROUGH THE WALL OFFSET 27
OUTSIDE CHASE ENCLOSURE 28
CHIMNEY INSTALLATION 29
FINISHING 30
LINTEL INSTALLATION 30
FIREPLACE FACING 30
DECORATIVE FACING FINISH 30
MANTEL 31
MANDATORY -FIREBOX LINING INSTALLATION 32
VERMICULITE REFRACTORY FIREBOX LINING INFORMATION 32
GLASS CLEANING 33
REPLACEMENT PARTS 33
30 YEAR LIMITED WARRANTY 34

4
RENAISSANCE RUMFORDTM 1000 LISTING LABEL
RENAISSANCE RUMFORDTM 1000 LISTING LABEL
The listing label has been placed on the left counterweight channel. To be able to consult
the label, fully open the firescreen and guillotine glass door. Use a portable lamp and look left
in the guillotine bay.
The listing label is permanently affixed and should not be removed.

5
IMPORTANT INSTALLATION SAFETY PRECAUTIONS
IMPORTANT INSTALLATION SAFETY PRECAUTIONS
Carefully follow all instructions. Improper installation of this fireplace and chimney
system could result in a house fire. Detailed explanations are in the sections which
follow.
For information about local building code requirements or the need for a permit,
contact your local municipal jurisdiction or fire department.
YES! WHAT TO DO
DO read this entire manual as well as the owner's
manual before starting the installation.
DO exercise caution when moving and positioning the
fireplace.
DO respect the mandatory installation sections.
DO inspect the fireplace, chimney, and
parts/components for damage prior to installation.
DO install all required parts and components as
instructed.
NO! WHAT NOT TO DO
DO NOT modify this fireplace or install parts or
components unapproved for use with this fireplace.
DO NOT install an unvented gas log set, gas lighter,
wood-burning fireplace insert or other products
unspecified for use with this fireplace.
DO NOT over fire this unit. Refer to operation
instructions in the Owner's Manual.
DO NOT allow combustible material within the
minimum clearance area of the fireplace and chimney
system.
DO NOT install non-combustible materials in the
required air flow spaces (e.g. do not install non-
combustible insulation inside a radiation shield).
COMBUSTIBLE VS NON-COMBUSTIBLE MATERIAL
The National Fire Protection Association (NFPA) defines Non-Combustible Materials as
materials that if used as directed, will not ignite, burn, support combustion, or release
combustible vapors when subjected to heat or flame. Non-Combustible Materials have passed
the ASTM E136, Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at
750°C
1
.
Combustible Materials are thus any materials that did not pass the ASTM E136 test such as
anything surfaced or including wood, plant fibers, plywood, Oriented Strand Board (OSB),
compressed paper, plastic and gypsum board (often called drywall or sheetrock)
2
which can
ignite and burn, whether it is flame-proofed or not, plastered or not plastered.
1
NFPA 211, Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
2
Note that gypsum board, whether fire-rated or not is considered combustible.

6
PLANNING THE INSTALLATION
PLANNING THE INSTALLATION
RECOMMENDATIONS
Before beginning, we strongly recommend adequate planning of your installation, including
the chimney and the hearth protection.
Refer to Figure 1 for an installation overview including critical components and warnings. The
planning process may involve your retail salesperson, installation personnel, outside
contractors and local building officials.
A building permit may be required. Check with your local authority to obtain the necessary
approvals before beginning. Close attention to detail and clear communication are important
to be sure that your Renaissance RUMFORDTM 1000 Fireplace is installed according to the
requirements in this manual and complies with local building codes.
IF THIS FIREPLACE IS NOT PROPERLY INSTALLED, A HOUSE FIRE
MAY RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION
INSTRUCTIONS AND CLEARANCE GUIDELINES.
CHOOSING A LOCATION AND RESTRICTIONS
When choosing a location for your fireplace, consideration should be given to best optimize
the performance of your chimney.
Optimal performance is achieved when a large portion of the chimney is within the building
envelope, centrally situated, allowing the chimney to terminate as close to the peak as
possible.
An insulated chase enclosure may be an acceptable alternative for the fireplace and chimney.
THERE ARE LOCATIONS WHERE THE FIREPLACE IS STRICTLY
PROHIBITED:
THE FIREPLACE MUST NOT BE INSTALLED OUTSIDE THE VAPOR
BARRIER OF THE HOME.
THE FIREPLACE MUST NOT BE INSTALLED OUTDOORS OR WITHIN
A THREE SEASON PORCH.
This fireplace is NOT APPROVED for use with a wood or gas fireplace insert.
IMPORTANT: A NON-COMBUSTIBLE HEARTH EXTENSION IS
REQUIRED IN FRONT OF THIS FIREPLACE. REFER TO THE "HEARTH
EXTENSION REQUIREMENTS" SECTION OF THIS MANUAL FOR
MORE INFORMATION ON THE HEARTH EXTENSION AND ITS
REQUIREMENTS.
For finishing specifications and allowable materials, refer to the "Fireplace Facing" section in
this manual.

7
PLANNING THE INSTALLATION
INSTALLATION OVERVIEW
*Refer to page 29 to determine the appropriate flashing (regular or vented)
FIGURE 1 GENERAL INSTALLATION OVERVIEW
*
MANDATORY –Roof Top
Radiation Shield

8
GENERAL SPECIFICATIONS
GENERAL SPECIFICATIONS
Under the 2015 U.S. EPA (Environmental Protection Agency) regulation, the Renaissance
RUMFORDTM 1000 is defined as a fireplace primarily for its decorative and aesthetic
prominence offering more than 500 square inches of pure fire viewing (930 square visible
inches).
When lined with the optional vermiculite panels, it has met the United States Environmental
Protection Agency (EPA) Voluntary Wood Burning Fireplace Program Phase 2 emission level.
It is:
•Typically burning at a rate of 4 kg/hr,
•Clean burning with an emission rate of 3.0 g/kg when burned with the door open and the
firescreen closed as tested with ASTM 2558
3
test protocol,
•Clean burning with an emission rate of 1.0 g/kg when burned with the door closed as
tested with ASTM 25583test protocol, and
•Clean burning with an equivalent emission rate of 4.19 g/hr when burned with the door
closed.
It comes fully equipped with a built-in guillotine glass door and a guillotine fire screen.
•Weight when crated is 740 lb. Floor reinforcement may be required.
•Do not remove the fireplace from its skid until it is ready to be installed.
•This fireplace is designed to burn wood logs; vented gas logs sets may also be used.
For gas log installation instructions, visit www.renaissancefireplaces.com.
•Gas log lighters are not permitted because they will burn out prematurely.
WARNING
THIS FIREPLACE HAS NOT BEEN TESTED WITH AN UNVENTED GAS
LOG SET. TO REDUCE RISK OF FIRE OR INJURY, DO NOT INSTALL
AN UNVENTED GAS LOG SET INTO THIS FIREPLACE.
3
ASTM 2558: Standard Test Method for Determining Particulate Matter Emissions from Fires in Low Mass Wood-
Burning Fireplaces.

9
GENERAL SPECIFICATIONS
FIREPLACE SPECIFICATIONS
FIGURE 2 FIREPLACE DIMENSIONS

10
GENERAL SPECIFICATIONS
FRAMING OVERVIEW
Walls on all interior sides of the fireplace enclosure should be finished and flat. Insulation or
other materials should not be placed within the required clearance spaces around the
fireplace.
The minimal recommended framing dimensions do not take into consideration the space
required for the outside air connection because the location for it and the space required
are specific to your installation. Take the time to plan.
FIGURE 3 MINIMAL FRAMING DIMENSIONS
Air space required
Do not frame against these sides or
directly on top of the fireplace casing
IMPORTANT:
INSULATION SHOULD ONLY BE
WITHIN THE FRAMING, NOT IN
THE SPACE BETWEEN THE
FRAMING AND THE FIREPLACE
Air space required
Do not frame against these sides or
directly on top of the fireplace casing

11
GENERAL SPECIFICATIONS
CHIMNEY OVERVIEW
FIGURE 4 GENERAL CHIMNEY REQUIREMENTS
TABLE 1 CHIMNEY SPECIFICATIONS
Chimney size and type
ICC RIS 10" only
Minimum chimney height: from the top of the fireplace to the chimney cap
12'
3,66 m
Maximum chimney height from the top of the fireplace to the chimney cap
60'
18,28 m
Maximum chimney height supported by the fireplace without additional
supports
15'
4,57 m
Minimum clearance between the exterior of the chimney and any
combustibles
2"
51 mm
Maximum number of offsets (2 elbows per offset)
2
*
Min.
Ceiling
Clearance
8' **
MANDATORY –Roof Top Radiation Shield
** See Table 2
(C) on page 21
for more details
*Refer to
page 29 to
determine the
appropriate
flashing
(regular or
vented)

12
FIREPLACE INSTALLATION
FIREPLACE INSTALLATION
Move the fireplace on its crate. Only unpack and/or remove from crate once the fireplace is
as close as possible to its final installation location.
INCLUDED WITH THE RENAISSANCE RUMFORDTM 1000
Item
Description
Quantity
1
Renaissance RUMFORDTM 1000 Fireplace
1
2
Pair of protective fireplace gloves
1
3
Chimney safety labels for each length of chimney in the attic
15
4
Smaller counterweight (approx. 10 lb, for the firescreen)
1
5
Bigger counterweight (approx. 25 lb each, for the glass door)
2
6
Pair of Renaissance andirons
1
7
Spark guard
1
8
Anti-tip bracket
1
9
Lifting handle
2
10
Manual bag (see list for contents)
1
11
Small brackets
4
On the crate with the
fireplace

13
FIREPLACE INSTALLATION
In the bag with the manuals
Item
Description
Quantity
1
Installation manual (English and French)
1
2
Owner's manual (English and French)
1
3
Door cover button –round black
2
4
Screw –self tapping 1" long hex head
4
5
Screw –self tapping 1/2" long hex head
15
6
Bottle of high temperature door grease
1
7
Removable door handle
1
8
Collar for 5" outside air connection (if necessary)
1

14
FIREPLACE INSTALLATION
MOVING THE RUMFORD 1000
The RUMFORD 1000 weighs 740 lb crated. The RUMFORD 1000 fireplace is front heavy. To
safely ship and transport the RUMFORD 1000, we have taken various parts from the front of
the fireplace and attach them to the back of the crate rendering the overall crate rather well-
balanced. As soon as you start removing heavy parts from the back of the crate, the rest of
the crate becomes unbalanced.
Careful attention must be taken when moving the fireplace with or without its shipping crate.
Whenever possible move the fireplace while it is still crated. We recommend using an Escalera
or equivalent dolly to move the fireplace, however, use caution when placing the dolly holding
strap, see Figure 5. Misplacement of the holding straps could result in damage to the guillotine
system.
•NEVER lean the fireplace on its side; doing so may damage the guillotine system which
is wider than the rest of the fireplace.
•NEVER lift the fireplace by the front or by the guillotine door opening; always handle the
fireplace by its casing or by the lifting handles provided on each side.
To prepare the RUMFORD 1000, locate it as close as possible to its final installation
position while on its crate.
The upper strap must be located just above the upper finishing lintel.
The lower strap must be located just under the metal front step.
FIGURE 5 ATTACHMENT STRAPS
THE FIREPLACE IS FRONT HEAVY. MAKE SURE TO ALWAYS
MAINTAIN CONTACT WITH THE FIREPLACE WHEN MOVING IT TO
PREVENT ANY UNDUE TILTING.

15
FIREPLACE INSTALLATION
ENGAGING THE GUILLOTINE SYSTEM
COUNTERWEIGHTS'INSTALLATION
Openings A and C allow the insertion of the counterweights. The openings will be
covered by cement board and do not have finishing metal cover plates.
x3 counterweight
cables
Left pulley
Right back pulley
Right front pulley
Start by placing the three counterweight cables through the openings A and C, and
over the pulleys. Allow the cables to hang down towards the door.
On the right side, the
bigger counterweight
goes on the back
On the right side, the smaller
counterweight goes on the
front, with the extended plate
towards the back
The counterweights will be supported by the pre-installed blocking rods. Ensure the
blocking rods are in position before inserting the counterweights.
Place each counterweight in its respective channel opening (A or C). On the right
side, the larger counterweight enters the rear channel and the smaller counterweight
enters the front channel. Ensure the smaller counterweight's extended metal plate
is oriented towards the back of the fireplace as shown above.
A
C
C
Blocking
Rod
Blocking
Rod
C
A
x2 on
Right

16
FIREPLACE INSTALLATION
Connect the three cables to the three counterweights and tighten the nuts that hold
them in place.
Connect the hanging cables to the bottom of the door left and right, and to the
bottom of the firescreen at the front right.
Using pliers, remove the caps on the back side of each blocking rod. Do not remove
the blocking rods yet.
Through opening A, ensure the cable is on the pulley, wearing gloves then grab hold
of the cable and pull to lift the counterweight off the blocking rod. Remove the
blocking rod. Gently release the cable so the weight is now hanging.
Repeat for the right side through opening C.
Do not attempt to lift the door at this point.
A
C
B
D
x2

17
FIREPLACE INSTALLATION
FIRESCREEN
Try moving the firescreen up and down slowly while looking at the cable and the pulley on
the right. Make sure the firescreen cable can move freely and centered over its pulley in a
straight line. If needed, realign the pulley. If you do so, do not forget to tighten the pulley's
nut and bolt without over tightening.
UNLOCKING THE GLASS DOOR
The guillotine glass door is held closed by two transportation blocking brackets,
located at the bottom of the door on each side. Remove the ¼" hex head screws and
the blocking brackets.
Locate the two door cover buttons in the manual bag and push them into the holes
in the door frame.
Lift the glass door to check the movement of the guillotine glass door. Make sure the cable
is centered in the pulleys and moves freely. Close both the guillotine glass door and the
firescreen.
WE RECOMMEND BOTH THE GUILLOTINE GLASS DOOR AND THE
FIRESCREEN REMAIN CLOSED WHILE COMPLETING THE
FIREPLACE AND CHIMNEY INSTALLATION.

18
MANDATORY INSTALLATIONS
MANDATORY INSTALLATIONS
MANDATORY - SPARK GUARD
Installation of the RUMFORD 1000 directly on the floor or on an elevated platform are
acceptable.
The fireplace must be installed on a level
surface. Standard framing will require
reinforcement to distribute the weight of
the fireplace.
The spark guard provided must be
installed 2½" under the fireplace base
and 2½" under the hearth extension,
centered on the fireplace opening. It is
dimensioned so that it will also cover the
entire floor area under the metal front
step of the fireplace. This guard prevents
sparks from lodging in this area and
starting a fire. See "Hearth Extension
Requirements" on page 22.
If you are installing the fireplace on a
combustible raised platform, you will
need a second spark guard (not provided)
with the same dimensions as the one we
have provided. One spark guard will be
installed below the hearth extension and
the raised platform. The second spark
guard will be installed below the fireplace.
Both spark guards must be centered on
the fireplace.
MANDATORY –SECURING THE FIREPLACE
Using the four small brackets that were securing the fireplace to the crate, attach the casing
of the fireplace to the floor. Position the brackets all around the fireplace in the same fashion
as they were on the crate. If possible, try to have the brackets screwed into the floor joists
with 2" wood screws.
MANDATORY - FIREBOX LINING OPTIONS (ONE CHOICE REQUIRED)
The RUMFORD 1000 has two options for the bricks that line the interior of the firebox. One of
the two options MUST be installed.
1. Vermiculite panels with a herringbone brick pattern (EO-VP1000). This choice
offers the cleanest burning fireplace on the market and a very classic herringbone look.
Pros: super low emissions, very fast startup.
Cons: Less durable than cement refractory bricks, expect to see wear and cracking
with these bricks over time.
2. Cement refractory bricks with a running bond brick pattern (EO-RB1000)
which offers the most durable solution for the Rumford and a very traditional look.
Pros: Durable and dependable, less maintenance and degradation over time.
Cons: The fireplace will not light as quickly.
FIGURE 6 SPARK GUARD INSTALLATION
Spark Guard is under the front
of the fireplace and extends
beyond the facing ofthefireplace

19
MANDATORY INSTALLATIONS
MANDATORY –ANTI-TIP BRACKETS
The RUMFORD 1000 fireplace MUST be securely fastened to the back wall. One anti-tip bracket
has been provided. It is attached to the top of the fireplace. The bracket can be removed and
repositioned as needed to ensure it aligns with the framing (see Figure 7). The anti-tip bracket
MUST be attached to the top of the fireplace.
Use the four 1" self-tapping screws provided to attach the bracket to the fireplace. Use four
wood screws (not included) to secure the bracket to the framing as shown in Figure 7.
FIGURE 7 ANTI-TIP BRACKET INSTALLATION
OPTION: INSTALL THE ANTI-TIP BRACKETS TO THE FRONT OR
BACK OF FRAMING AS ILLUSTRATED. SEE FIGURE 7.
Anti-Tip Stability Bracket:
•On either side of the
chimney coupling
•On the front side or
the back side of an
horizontal 2"x4"
x4
x4

20
MANDATORY CLEARANCES
MANDATORY CLEARANCES
FIREPLACE CLEARANCES
Clearance to combustibles are critical to the safe operation of this fireplace.
FIGURE 8 FIREPLACE CLEARANCES (SEE TABLE 2)
CEILING HEIGHT REQUIREMENTS
Using the components included with the RUMFORD 1000, the minimum ceiling height
measured from the base of the fireplace to the ceiling is 8'. This requirement applies to ALL
ceilings above the fireplace (room ceiling, enclosure ceiling).
45"
Table 4
12"
Table 3 for
24"
24"