Renogy Commander Series User manual

0
Commander Series
RENOGY 60A
Maximum Power Point Tracking Solar Charge Controller
2775 E. Philadelphia St., Ontario, CA 91761
1-800-330-8678
Version 3.0

1
Important Safety Instructions
Please save these instructions.
This manual contains important safety, installation, and operating instructions for the
charge controller. The following symbols are used throughout the manual to indicate
potentially dangerous conditions or important safety information.
WARNING: Indicates a potentially dangerous condition. Use extreme caution when
performing this task.
CAUTION: Indicates a critical procedure for safe and proper operation of the controller
NOTE: Indicates a procedure or function that is important to the safe and proper operation
of the controller.
General Safety Information
•Read all of the instructions and cautions in the manual before beginning the
installation.
•There are no serviceable parts for this controller. Do NOT disassemble or attempt
to repair the controller.
•Do NOT allow water to enter the controller.
•Make sure all connections going into and from the controller are tight.
Charge Controller Safety
•NEVER connect the solar panel array to the controller without a battery. Battery
must be connected first.
•Ensure input voltage does not exceed 150 VDC to prevent permanent damage.
Use the Open Circuit (Voc) to make sure the voltage does not exceed this value
when connecting panels together.
•Do not exceed 60A forthe charge controller The Short Circuit (Isc) of the solar array
should be less than 60A.

2
Battery Safety
•Use only sealed lead-acid, flooded, or gel batteries which must be deep cycle.
•Explosive battery gases may be present while charging. Be certain there isenough
ventilation to release the gases.
•Be careful when working with large lead acid batteries. Wear eye protection and
have fresh water available in case there is contact with the battery acid.
•Carefully read battery manuals before operation.
•Do NOT let the positive (+) and negative (-) terminals of the battery touch each
other.
•Recycle battery when it is replaced.
•Over-charging and excessive gas precipitation may damage the batteryplates and
activate material shedding on them. Too high of an equalizing charge or too long
of one may cause damage. Please carefully review the specific requirements of
the battery used in the system.
•Equalization is carried out only for non-sealed / vented/ flooded / wet cell lead acid
batteries.
•Do NOT equalize VRLA type AGM / Gel cell batteries UNLESS permitted by
battery manufacturer.
WARNING: Connect battery terminals to the charge controller BEFORE connecting
the solar panel(s) to the charge controller. NEVER connect solar panels to charge
controller until the battery is connected.
WARNING: Do NOT connect any inverters or battery charger into the load terminal
of the charge controller.
WARNING: Once equalization is active in the battery charging, it will not exit this
stage unless there is adequate charging current from the solar panel. There should
be NO load on the batteries when in equalization charging stage.

3
Table of Contents
General Information....................................................................................................................................4
Additional Components..............................................................................................................................8
Optional Components.................................................................................................................................8
Identification of Parts .................................................................................................................................9
PV Array Requirements............................................................................................................................10
PV Strings..............................................................................................................................................10
PV Max Power .......................................................................................................................................10
Installation .................................................................................................................................................11
Operation ...................................................................................................................................................16
1. Monitoring .........................................................................................................................................17
2. Log Info..............................................................................................................................................18
3. Clock Set............................................................................................................................................19
4. Local Para Set...................................................................................................................................19
5. Control Para Set................................................................................................................................20
6. Sys Password ...................................................................................................................................22
7. Default Set .........................................................................................................................................22
8. Dev Msg.............................................................................................................................................22
System Status Icons.................................................................................................................................23
LED Indicators...........................................................................................................................................23
Commander Protections ..........................................................................................................................24
System Status Troubleshooting..............................................................................................................25
Maintenance ..............................................................................................................................................26
Fusing.........................................................................................................................................................26
Technical Specifications..........................................................................................................................27
Electrical Parameters ...........................................................................................................................27
Charging Parameters ...........................................................................................................................28
Charging Parameters Glossary...........................................................................................................28
Mechanical Parameters........................................................................................................................30
Environment Parameters .....................................................................................................................30
Conversion Efficiency Curves.............................................................................................................31
PC Software...............................................................................................................................................33
Dimensions................................................................................................................................................36

4
General Information
The RENOGY Commander MPPT controller is suitable for off-grid solar applications. It
protects the battery from being over-charged by the solar modules and over-discharged
by the loads.The controller features a smart tracking algorithm that maximizes the energy
from the solar PV module(s) and charge the battery.
The MPPT Charge Controller charging process has been optimized for long battery life
and improved system performance. The comprehensive self-diagnostics and electronic
protection functions can prevent damage from installation mistakes or system faults. In
addition, the controller is a high-end industrial class product based on multiphase
synchronous rectification technology and has features of high efficiency and reliability.
Key Features
•LCD display with 6 button combination for easy operation.
•12V / 24V / 36V / 48V DC systems. 
•Advanced maximum power point tracking technology with the tracking efficiency
as high as 99.5%
•Multiphase synchronous rectification technology ensuring peak conversion
efficiency up to 98%
•Excellent heat dissipation with integration of the cast aluminum radiator shell. The
controller can be natural cooling.
•Unique dual timer function; enhance the flexibility lighting systems. 
•Deep cycle Sealed, Gel, Flooded or User battery option.
•Adopting temperature compensation and correcting the charging and discharging
parameters automatically, improving battery lifetime. 
•Electronic protection: Overcharging, over-discharging, overload, and short circuit.
•Protection against over-temperature, over-charging, PV short, reverse polarity,
and over current. 
•RS-232, RS-485, and CAN port compatible for extra features.
•Remote Temperature Sensor adaptable and Battery Voltage Sensor adaptable
MPPT Technology
The Commander MPPT Charge Controller utilizes Maximum Power Point Tracking
technology to extract maximum power from the solar module(s). The tracking algorithm
is fully automatic and does not require user adjustment. MPPT technology will track the
array’s maximum power point voltage (Vmp) as it varies with weather conditions, ensuring
that the maximum power is harvested from the array throughout the course of the day.
Current Boost
In many cases, the Commander MPPT charge controller will “boost” up the current
in the solar system. The current does not come out of thin air. Instead, the power

5
generated in the solar panels is the same power that is transmitted into the battery bank.
Power is the product of Voltage (V) x Amperage (A). Therefore, assuming 100%
efficiency:
Power In = Power Out
Volts In * Amps In = Volts out * Amps out
Although MPPT controllers are not 100% efficient, they are very close at about 92-95%
efficient. Therefore, when the user has a solar system whose Vmp is greater than the
battery bank voltage, then that potential difference is proportional to the current boost.
The voltage generated at the solar module needs to be stepped down to a rate that could
charge the battery in a stable fashion by which the amperage is boosted accordingly to
the drop. It is entirely possible to have a solar module generate 8 amps going into the
charge controller and likewise have the charge controller send 10 amps to the battery
bank. This is the essence of the MPPT charge controllers and their advantage over
traditional charge controllers. In traditional charge controllers, that stepped down voltage
amount is wasted because the controller algorithm can only dissipate it as heat. The
following demonstrates a graphical point regarding the output of MPPT technology.
Limiting Effectiveness
Temperature is a huge enemy of solar modules. As the environmental temperature
increases, the operating voltage (Vmp) is reduced and limits the power generation of the
solar module. Despite the effectiveness of MPPT technology, the charging algorithm will
possibly not have much to work with and therefore there is an inevitable decrease in
performance. In this scenario, it would be preferred to have modules with higher nominal
voltage, so that despite the drop in performance of the panel, the battery is still receiving
a current boost because of the proportional drop in module voltage.
Typical Battery
Voltage Range
Maximum
Power Point
Traditional
Controller
Operating
Range
Maximum
Power Point
Current vs. Voltage (12V System)
Output Power (12V System)

6
Four Charging Stages
The Commander MPPT charge controller has a 4-stage battery charging algorithm for a
rapid, efficient, and safe batterycharging. They include: Bulk Charge, Boost Charge, Float
Charge, and Equalization*.
Bulk Charge: This algorithm is used for day to day charging. It uses 100% of available
solar power to recharge the battery and is equivalent to constant current. In this stage the
battery voltage has not yet reached constant voltage (Equalize or Boost), the controller
operates in constant current mode, delivering its maximum current to the batteries (MPPT
Charging)
Constant Charging: When the battery reaches the constant voltage set point, the
controller will start to operate in constant charging mode, where it is no longer MPPT
charging. The current will drop gradually. This has two stages, equalize and boost and
they are not carried out constantly in a full charge process to avoid too much gas
precipitation or overheating of the battery.
➢Boost Charge: Boost stage maintains a charge for 2 hours by default. The user
can adjust the constant time and preset value of boost per their demand.
Float Charge: After the constant voltage stage, the controller will reduce the battery
voltage to a float voltage set point. Once the battery is fully charged, there will be no more

7
chemical reactions and all the charge current would turn into heat or gas. Because of this,
the charge controller will reduce the voltage charge to smaller quantity, while lightly
charging the battery. The purpose for this is to offset the power consumption while
maintaining a full battery storage capacity. In the event that a load drawn from the battery
exceeds the charge current, the controller will no longer be able to maintain the battery
to a Float set point and the controller will end the float charge stage and refer back to bulk
charging.
Equalization: Is carried out every28 days of the month. It is intentional overcharging
of the battery for a controlled period of time. Certain types of batteries benefit from
periodic equalizing charge, which can stir the electrolyte, balance battery voltage and
complete chemical reaction. Equalizing charge increases the battery voltage, higher than
the standard complement voltage, which gasifies the battery electrolyte.
WARNING: Once equalization is active in the battery charging, it will not exit this
stage unless there is adequate charging current from the solar panel. There should
be NO load on the batteries when in equalization charging stage.
WARNING: Over-charging and excessive gas precipitation may damage the battery
plates and activate material shedding on them. Too high of equalizing charge or for
too long may cause damage. Please carefully review the specific requirements of
the battery used in the system.
WARNING: Equalization may increase battery voltage to a level damaging to
sensitive DC loads. Ensure that all load allowable input voltages are greater than
the equalizing charging set point voltage.

8
Additional Components
Remote Temperature Sensor (TS-R): Measures the
temperature at the battery and uses this data for very accurate
temperature compensation. It is not polarity sensitive.
USB to RS-485 Converter: The USB to RS-485 converter is
used to monitor each controller on the network using Solar
Station Monitor PC software and update the firmware. It connects
to the RS-485 port on the controller. Download the PC software
through Renogy’s website under the “Downloads” section
Optional Components
Optional components that require a separate purchase:
External Battery (RTC): Allows for the access to the charge controller’s saved settings,
charge accumulation, and discharge accumulation without connecting to a deep cycle
battery. It keeps track of the date/time (once set) for automatic equalization processes.

9
Identification of Parts
2
3
4
5
6
1
7
10
9
7
8
7
7
7
11
12
13
14
Top View
Front View (Hatch Removed)

10
Key Parts
1. Grounding Bolt
2. LCD Display
3. Battery LED
4. PV LED
5. Fault LED
6. Navigation Buttons
7. RS-485 port—monitor controller through PC and update firmware
8. RTC Battery Slot—model is CR2032
9. Remote Temperature Sensor Port—optional accessory to remotely monitor battery
temperature
10.Remote Battery Voltage Sensor Port—Provides accurate battery voltage
measurement
11.Reserved Port—Reserved port for future development. Special accessory currently
not sold.
12. RS-232 port—monitor controller through PC and update firmware
13. PV Terminal
14. Battery Terminal
PV Array Requirements
PV Strings
The commander is suitable for various types of PV configurations to maximize electrical
energy. Configurations are dependent on the open circuit voltage (Voc) and maximum
power point voltage (Vmp) located in solar panel specifications. The following table is to
serve as a reference only.
System Voltage
36 Cell Module
(Voc < 23V)
60 Cell Module
(Voc < 38V)
72 Cell Module
(Voc < 46V)
Max
Best
Max
Best
Max
Best
12V
4
2
2
1
2
1
24V
6
3
3
2
3
2
48V
6
5
3
3
3
2
Note: The above parameter values are calculated under the STC conditions: Irradiance 1000W/m2,
Temperature 25°C, Air Mass 1.5
PV Max Power
The Commanders have a limiting current function, where the current is limited within a
range, and therefore allows battery charging at the correct value despite oversized input
power. The power operation follows the following conditions:

11
1. PV Actual Power ≤ controller rated charge power, the controller charge battery at
the actual maximum power point.
2. PV Actual Power ≤ controller rated charge power, the controller charges the
battery at the rated power.
WARNING: The Commander will be damaged if the PV array is 3X greater than the
actual operating power of the controller.
WARNING: The Commander’s reverse polarity is no longer warranted if the PV
array size is 1.5X greater than the rated power of the controller.
The following tables serves as the reference guide for the statements above:
Model
Rated Charge
Current
Rated Charge
Power
Max PV Array
Power
Max PV Voc
Input
Commander
60A
800W @ 12V
1600W @ 24V
2400W @ 36V
3200W @ 48V
2400W @ 12V
4800W @ 24V
7200W @ 36V
9600W @ 48V
150V @
minimum
operating
environmental
temperature
OR
138V @ 25°C
environmental
temperature
Installation
Recommended tools to have before installation:
Flathead Screwdriver
Multi-Meter
WARNING: Connect battery terminal wires to the charge controller FIRST then
connect the solar panel(s) to the charge controller. NEVER connect solar panel to
charge controller before the battery.

12
CAUTION: Do not over-torque or over tighten the screw terminals. This could
potentially break the piece that holds the wire to the charge controller.
CAUTION: Refer to the technical specifications for max wire sizes on the controller
and for the maximum amperage going through wires.
You are now ready to begin connecting your battery to your charge controller.
Battery
1
2
3
4

13
Solar Panels
Computer connection
2
2
1
1

14
Temperature sensor (Not Polarity Sensitive)
1
2
3
4

15
Mounting Recommendations
NOTE: The Commander MPPT 60 controller requires at least 6 inches(150mm) of
clearance above and below for proper air flow. Ventilation is highly recommended
if mounted in an enclosure.
WARNING: Never install the controller in a sealed enclosure with flooded batteries.
Gas can accumulate and there is a risk of explosion.
1. Choose Mounting Location—place the controller on a vertical surface protected
from direct sunlight, high temperatures, and water. Make sure there is good
ventilation.
2. Check for Clearance—verify that there is sufficient room to run wires, as well as
clearance above and below the controller for ventilation. The clearance should be
at least 6 inches (150mm).
3. Mark Holes—Mark the four mounting holes locations on the mounting surface.
4. Drill Holes—Remove the controller and drill four sizeable holes at the marked
locations.
5. Secure the charge controller—Place the controller on the surface and align the
mounting holes with the drilled holes in step 4. Secure the controller in place using
the mounting screws.

16
Operation
After connecting the battery to the charge controller, the controller will turn on
automatically. The user will be prompted by an initialization screen, followed by the
charge controller’s rated parameters, and finally the default monitoring screen.
Use the following buttons to maneuver through the menu:
Cycle through the menu
Cycle through the menu
Return to main menu in any monitoring interface
Modify any value and set period of Log to browse
Modify any value and set period of Log to browse
Selecting certain parameters
Select to display the menu screen selection. The user will have 9 interfaces to
choose from.
1. Monitoring
2. Log Info
3. Clock Set
4. Local Para Set
5. Control Para
6. Sys Password
7. Default Set
8. Device Msg
NOTE: You might be prompted to enter a password. Simply put “0” all the way
through by pressing
NOTE: To customize charge parameters, BATT TYPE must be set to USER under
5. Control Param


ESC
+
-
OK
Rated Parameters
Rat.Volt 48.0V
Charg.Cur 60.0A
Disc.Curr 60.0A
ESC
OK

17
NOTE: The values found in your controller are default values and will not
necessarily match the ones listed. The values on this table are to show the user
what the different screens are used for.
NOTE: You do NOT have to program the control. These parameters are for extra
features. Once you connect the battery the settings are automatically synced.
1. Monitoring
Use the keys to maneuver through the screens and to access the
menu
Default monitoring screen displaying charge controller
system status through icons.
Indicates battery voltage and battery current
Indicates the maximum and minimum battery values
since the charge controller has been turned on. When
battery is charging, the values are expected to
change.
Displays the battery state as well as the state of
charge of the battery.
NOTE: The Battery SOC% is an estimation based on
the charging voltage.
Displays the charging state of the battery as well as
the voltage coming from the PV module(s).
NOTE: Make sure PV input is not more than 150 VDC

Charge State
No Charge
PV Volt
0.0 V

Batt State
Normal
Batt SOC
51%

Batt Day’Max
12.8 V
Batt Day’Min
12.6 V

Batt Volt.
12.6 V
Batt Cur.
0.0 A

0.00A 12.65V 0.00A
Jan 12:12: 12
10


ESC

18
Indicates the amount of energy that has been
generated for the day in terms of kilowatt-hours per
day. The PV power indicates how much power the PV
modules have generated.
Indicates the total amount of energy generated and in
kilowatt-hours per day.
Indicates the batteries temperature as well as the
temperature compensation. Temperature fluctuation
can affect performance in the system. The purpose of
temperature compensation is to adjust the
performance of the system to keep the system
functioning normally.
Indicates the local temperature of the charge
controller.
2. Log Info
Use the keys to maneuver through the screens and to access the
menu
Users will be able to see segments of how
Commander is performing when the whole system is
connected through the work log. Any time there is a
change in voltage or amperage it will be logged onto
the Work Log Query. It is recommended that the date
and time be set correctly so that a range of dates can
be selected and analyze solar performance.
Depending on the total amount of Work Logs, users
can cycle through the logs using the (up) and (down)
arrows. Press ESC to go back to the previous log
menu. The logs display battery voltage and battery
current.
Local Temperature
23.4 oC

Batt Temp
25.0 °C
Temp Coefficient
-3mV / °C / 2V

Total Generated
55 kWh/D

Generated Energy
55 kWh/D
PV Power
0.0 W
ESC
No. 1/121
2015-01-23 1:01
Batt Vol 51.6 V
Batt Curr 0.0A

Work Log Query
From 2015-01-23
To 2015-02-01
Total: 121
OK
<1>Work Log
<2> Alarm Log


ESC

19
The Alarm Log will display any kind of faults or
warnings that the charge controller experienced while
having the solar system connected. As in the previous
Log, users can cycle through how many alarm logs
are available and observe the data.
3. Clock Set
Press to highlight the month in the clock set menu and use the keys
to change the parameter. Press to confirm and save the settings.
Users can set the date and time. The clock uses a 24
hour clock.
NOTE: In some models, users might be prompted to
enter a password. Simply put “0” all the way through
and press OK.
4. Local Para Set
Use the keys to maneuver through the screens and to access the
Menu
Press to highlight the parameter and use the keys to change the
parameters. Press to confirm and save the settings.
The Local ID number is the charge controller’s unique
ID when identifying it in a network or utilizing the PC
software to search for the charge controller.
The charge controller’s LCD interface is backlit and
this interface lets you knowthe amount of secondsthe
LCD will be illuminated once the last button is
pressed. The range is from 1-90 seconds and the “–
“symbol indicates the backlight is never off. The
storage log is from 1-30 minutes. It relates to how
often the charge controller collects data and inputs
into the Work Log or Alarm log.
Alarm Log Query
From 2015-01-23
To 2015-02-01
Total: 0
OK
<1>Work Log
<2> Alarm Log
Clock Set
Aug-05-2015
13:16:51
Backlight Time
60 s
Storage Interval
10 min

Local ID
T03-0001
OK
OK
+
-


ESC
OK
+
-
OK