Renown REN08002-VP User manual

All Metal Construction • 20" Deck • 19" Pad Driver
• Triple Planetary All Steel Gear Box • Universal Clutch Plate
• Safety Lock-Out Switch • 50' Cord • 66-Frame Motor
• Warranty
175 RPM FLOOR MACHINE
REN08002-VP
www.GoRenown.com
883075
R

R
Specifications:
• Model: REN08002-VP
• Power: 1.75 hp actual (1.5 hp as
CSA-US rated)
• Deck Size: 20" (50.8 cm)
• Voltage: 110 volt
• Speed: 175 rpm
• Power Cable: 50 ft. (15.2 m) safety
yellow
• Weight: 109 lbs (49.4 kg)
• Amp Draw: 12.0 amps
• Warranty: 5 years motor and gear
box. 5 years metal components.
! WARNING !
IMPORTANT SAFETY
INSTRUCTIONS
Carefully read and understand this
manual before operating this
machine.
This machine must be grounded!
This floor/finishing machine shall be
grounded while in use to protect the
operator from electric shock.
Grounding provides a path of least
resistance for electric current. This
machine is equipped with a cord
having an equipment-grounding con-
ductor and grounding plug. The plug
must be plugged into an appropriate
outlet that is properly installed and
grounded in accordance with all local
codes and ordinances. Do not remove
the ground pin under any circum-
stances.
This machine is for use on a nominal
120-volt circuit and has a grounding
plug that resembles the plug illustrated
in Figure 1. Make sure that the
machine is connected to an outlet
having the same configuration as the
plug. No adapter should be used with
this machine.
This machine is intended for commer-
cial use. It is constructed for use in an
indoor environment and is nor intended
for any other use. Use only recom-
mended accessories.
1. Do not operate machine:
– Unless trained and authorized.
– Unless you have read and under-
stand the operators manual.
– In flammable or explosive areas.
– With a damaged cord or plug.
– If not in proper operating condition.
– In outdoor areas.
– In standing water.
– With the use of extension cords.
2. Before operating machine:
– Make sure all safety devices are in
place and operating properly.
3. When using machine:
– Do not run machine over cord.
– Do not pull machine by cord or
plug.
– Do not pull cord around sharp
edges or corners.
– Do not unplug by pulling on the
cord.
– Do not stretch cord.
– Do not handle plug with wet hands.
– Keep cord away from heated
surfaces.
– Report machine damage or faulty
operation immediately.
4. Before leaving or servicing
machine:
– Turn off machine.
– Unplug cord from outlet.
5. When servicing machine:
– Unplug cord from outlet.
– Use manufacturer supplied or
approved replacement parts.
175 RPM FLOOR MACHINE
SAFETY PRECAUTIONS
Grounded
Outlet Box
Grounded
Outlet
Prong or
Grounding Pin
Figure 1
2
www.GoRenown.com
To avoid electric shock,
please replace the power cord
immediately if any damage is detected.
Repairs must be performed only by
authorized and ualified persons.
R
q

175 RPM FLOOR MACHINE
OPERATING INSTRUCTIONS
General Use:
1. Remove any obstructions or other
obstacles in the area which is to be
cleaned.
2. Place the handle in the upright
position and tilt machine back until
handle rests on the floor.
Be sure the machine is not plugged
into an outlet.
3. Attach the pad driver or brush to the
machine by placing the clutch plate
over the gearbox hub and turning
the driver/brush 1/4 turn.
4. Place machine back into its upright
position.
5. Plug power cord into a grounded
outlet.
Never use an extension cord in con-
junction with the standard power cord.
6. The handle height may be adjusted
by lifting up the compression handle
which is located on the right side of
the handle tube about 1 foot above
floor level. Release the compression
handle and adjust handle to safe
operating height, then push back
down on the compression handle
to lock the handle in operating
position.
7. To start the machine, press the
red safety button on the top of the
upper switch housing, and then
squeeze either of the operating
triggers. (the safety button must be
depressed prior to squeezing the
operating triggers).
8. When the machine is in operation,
both hands should be placed on the
switch housing (upper handle).
9. During operation, to make the
machine go right, gently raise the
handle. To make the machine go
left, gently lower the handle.
10. To stop the machine at any time,
simply release the operating trig-
ger(s) and the machine will stop
automatically.
Maintenance:
To keep the machine performing
well for many years, please follow
the following maintenance proce-
dures.
Always confirm that the machine is
unplugged prior to performing any
maintenance or repairs.
1. Unplug machine as soon as you are
done using it.
2. Tilt machine back and remove pad
driver or brush.
Never store a low speed machine
with the pad driver or brush mounted
to the machine.
3. Clean the outside of the machine
with a mild cleaner.
4. Check power cord for any damage.
If damage is detected, replace
power cord immediately.
5. Lubricate wheels with a water
resistant lubricant once a month.
6. Check machine for loose or missing
nuts and bolts, and replace as
necessary.
7. If the machine is used in a dusty
environment, you may remove the
motor cover and blow the motor
clean with compressed air. This will
ensure proper ventilation, and allow
the motor to run cooler.
Storage:
1. Unplug machine from power source
and wrap cord on handle.
2. Tilt machine back and remove pad
driver or brush.
3. Store machine in upright position
and in a dry area.
3
www.GoRenown.com
R

175 RPM FLOOR MACHINE
HANDLE GROUP
4
www.GoRenown.com
R

VF47035AS
AS22004S
AS22005S
AS22012
VF41004AS
AS22010
VF30027
VF50120A
15
14
13
36
12
11
9
8
COVER, HOOK
VF30014
7
175 RPM FLOOR MACHINE
HANDLE GROUP PARTS LIST
5
www.GoRenown.com
R
DIA
NO
PART
NUMBER
NO
REQ'D
1 VF30016 1
2
VF300152 1
3 VF30018 2
4
5
VF30017 1
VF45125 1
1
10
VF13504 1
1
VF13493 1
AS312206B 1
16 1
17 VF48310 2
18 AS22006S 1
19 1
20 VV13661 2
21 VF48309 1
22 VF45119 1
23 AS22009 1
24 GT13009 5
25 GT13008 2
26 1
27 GV40218 1
28 GV40209 1
29 1
30 VF99010C 1
31 VF44203 1
32 VF14212 2
33 1
34 AS312203 1
35 1
VF13604 4
VF14222 4
LEVER,RIGHT,SWITCH
COVER
LABEL,FRONT COVER
TEETH WASHER,M5
SCREW,M5X12
SPRING,SAFETY BUTTON
SAFETY BOTTON
SCREW,M3X25
CLAMP BLOCK
CORD,POWER SUPPLY
STRAIN RELIEF,CORD
SCREW,M5X30
SCREW,M5X20
SERIAL TAG
LEVER,SOLUTION
LEVER,LEFT,SWITCH
SCREW,M4X12
REAR COVER
BREAKER, CIRCUIT, 17A / A-0701HS
SWITCH ASSY
SCREW,M6X10
TUBE
FRONT COVER
HANDLE GRIP
CORD,HANDLE
GROMMET
NUT,LOCK,M10
WASHER,PLAIN
DESCRIPTOIN
HANDLE RELEASE
BOLT HANDLE RELEASE
WASHER,PLAIN
SCREW
VF300141 1
CORD WRAP BLOCK
VF13570
VF40169
1
1
PIN
CONNECTION PLATE
61